JBJeffrey P. Bons

Jeffrey P. Bons

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jeffrey P. Bons has a total of 52 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • The Effect of Thermal Cycling on Deposition in an Impingement/Effusion Cooling Geometry

    by George J. Gogidze, Jeffrey P. Bons, Ryan Lundgreen

    Experiments were conducted in a high-pressure deposition facility to study the effect of engine cycling on the successive buildup of deposits as aircraft shut down and power up. The test facility simulates the pressure and temperature environment of a combustor liner or turbine vane cooling circuit. The coolant flow temperature reaches 894 K (1150 °F) and discharges into a 17-atm (250-psi) cavity pressure at a nominal pressure ratio of 1.027. AFRL05 test dust with a 0- to 10-µm size distribution is added to the coolant gas stream. The cooling circuit consists of a double-walled impingement/effusion cooling plate with nominal hole sizes on the order of 0.5 mm. To simulate cycling, the facility is brought up to the desired operating conditions where the first batch of dust is delivered (2–8 g). The facility is then ramped down to ambient conditions. Following a “dwell” period of approximately 24 h, another batch of dust is delivered once the facility is brought back up to the desired operating condition. Test data were acquired for one, two, and four cycles with different dust masses delivered. Values such as discharge coefficient, pressure ratio, Reynolds number, and temperature are used to evaluate the effects of dust deposition on the impingement/effusion plate setup. Dust capture efficiency is shown to be insensitive to cycling whereas flow blockage is negatively impacted by an increased number of cycles for the same total mass delivered. The sloughing of deposit structures during cooling circuit cool down is postulated to be responsible for the observed behavior.


  • A Simplified Injection Model for Variable Area Turbine Fluidic Throttling

    by Alexander Spens, Evan J. McFadden, Cole D. Westrick, Jeffrey P. Bons

    Previous studies have demonstrated the effectiveness of using fluidic actuators to throttle the flow through a nozzle guide vane, enabling a variable area turbine (VAT) with no moving parts. A simplified model was developed to assess the driving design factors that influence the blocked flow fraction and throttling effectiveness of the actuators. The model approximates slot injection using a simplified stream tube analysis, neglecting mixing with the primary passage flow. Throttling performance is predicted for fluidic actuators with different widths, orientations, streamwise locations, and pressure ratios. This simplified model evaluates these actuators in a constant width straight duct and a variable width duct. Two-dimensional CFD of injection in the nozzle guide vane passage reported strong agreement with the results of the simple model using the variable width duct. Higher injection pressure ratios result in more injected mass flow but not significantly higher throttling effectiveness. Wider slots retain the effectiveness and block much more primary flow. Upstream oriented injection proves best for both effectiveness and blockage capabilities. Finally, there is an optimal injection location relative to the passage throat, which is extracted by both the model and CFD. This model has potential application for optimizing fluidic VAT throttling designs while saving on the cost of high-fidelity testing and production of these configurations.


  • Mineral Composition Effects on Dust Deposition at Realistic Engine Conditions

    by Nathanael J. Wendel, Noah P. Subasic, Andrew E. Mizer, Jeffrey P. Bons

    In this article, the role of mineral composition was assessed for Air Force Research Laboratory Test Dust (AFRL), for deposition in a realistic gas turbine engine environment. Experiments were performed on an effusion cooling test article with a coolant flow temperature of 894 K and surface temperature of 1144 K. Aerosolized dust with a 0–10 µm particle size distribution was delivered to the test article. The mineral recipe of AFRL was altered such that the presence of each of the five components ranged from 0% to 100%, and capture efficiency, hole capture efficiency, blockage per gram, and normalized deposit height were reported. Results are compared to a previous study of the intermineral synergies in an impingement cooling jet at the same temperature conditions. Despite differences in experimental facility flow geometry, overall agreement was found between the trends in the deposition behavior of the dust blends. The strong deposition effects that were observed were shown to be related to adhesion forces of particles, mechanical properties, and chemical properties of the dust minerals. Supplemental testing was performed in a high-temperature (1425–1650 K) impinging jet (200–260 m/s) to evaluate mineral effects at hot gas path conditions. Capture efficiency and morphology of dust deposits are reported. The capture efficiency in this regime was shown to correlate well with temperature, with chemical effects being secondary. An attempt was made to predict capture efficiency using chemical assessments such as a ratio of bases to acids, Ca:Si ratio, and optical basicity with only modest success.


  • Active Fluidic Control of a Nozzle Guide Vane Throat

    by Alexander Spens, Jeffrey P. Bons

    Experiments were conducted to validate the building blocks of a fluidically controlled variable area turbine concept that uses injected high-pressure air to effectively reduce the choke area of the turbine inlet. Preliminary results from a simple quasi-1D converging-diverging nozzle, with an injection flow slot upstream of the throat, showed a 2.2:1 ratio between throttled mass flowrate and injected mass flowrate at a constant nozzle pressure ratio. The penetration of the injection flow and corresponding reduction in the primary flow streamtube were successfully visualized using a shadowgraph technique. Building on this success, a representative single passage nozzle guide vane transonic flowpath was constructed to demonstrate feasibility beyond the quasi-1D converging-diverging nozzle. Both secondary slot blowing from the vane pressure surface and vane suction surface just upstream of the passage throat again successfully reduced primary flow. In addition, fluidic vortex generators were used on the adjacent suction surface to reduce total pressure loss and further throttle the primary flow. Implications for the application of this active flow control technology to a variable area turbine are considered.


  • Unpacking Intermineral Synergies and Reactions During Dust Deposition in an Impingement Coolant Jet

    by Eric P. Nied, Jeffrey P. Bons, Ryan K. Lundgreen

    This paper seeks to unpack synergies that exist between minerals during deposition of the heterogeneous AFRL02 mixture in gas turbine engines and demonstrate that the contributions of each mineral cannot be considered independently. In each experiment, one gram of mineral dust (0–10 µm particle diameter distribution) was injected into an 894 K, 57 m/s coolant flow impinging normally on a Hastelloy X plate with a surface temperature of 1033 K, 1144 K, or 1255 K. Capture efficiency measurements, deposit morphology analyses, and X-ray diffraction results are reported. Besides AFRL02, single mineral dusts, dual mineral dusts, and AFRL02-like dust blends lacking in one mineral were tested. The results of the experiments elucidate that the deposition behavior of single minerals indeed cannot explain the composite deposition of heterogeneous mixtures. For example, gypsum had the highest capture efficiency of any single mineral in ARFL02, and yet removing gypsum from AFRL02 counterintuitively raised the capture efficiency of that blend when compared to AFRL02. Quartz was found to erode albite deposits but stick to and build upon dolomite and halite deposits, even though quartz did not deposit significantly as a single mineral. Quartz also chemically reacted with gypsum and dolomite to form wollastonite and diopside, respectively. Finally, we found that the capture efficiency of each blend increased with plate temperature, but not according to the same trend. Results are interpreted through the lens of CaO–MgO–Al2O3–SiO2 eutectic chemistry, but the chemical pathways by which these eutectics come into existence is found to be of equal importance.


  • An Improved Particle Impact Model by Accounting for Rate of Strain and Stochastic Rebound

    by Steven M. Whitaker, Jeffrey P. Bons

    A methodology for informing physics-based impact and deposition models through the use of novel experimental and analysis techniques is presented. Coefficient of restitution (CoR) data were obtained for Arizona Road Dust (ARD), AFRL02 dust, and each component of AFRL02 impacting a Hastelloy X plate at a variety of flow temperatures (295–866 K), surface temperatures (295–1255 K), particle velocities (0–100 m/s), and impact angles (0–90 deg). High speed particle shadow velocimetry (PSV) allowed individual impact data to be obtained for more than 8 million particles overall, corresponding to 20 combinations of particle composition, flow temperature, and surface temperature. The experimental data were applied to an existing physics-based particle impact model to assess its ability to accurately capture the physics of particle impact dynamics. Using the experimental data and model predictions, two improvements to the model were proposed. The first defined a velocity-dependent “effective yield strength,” designed to account for the effects of strain hardening and strain rate during impact. The second introduces statistical spread to the model output, accounting for the effect of randomizing variables such as particle shape and rotation. Both improvements were demonstrated to improve the model predictions significantly. Applying the improved model to the experimental data sets, along with known temperature-dependent material properties such as the elastic modulus and particle density, allowed the temperature dependence of the effective yield strength to be determined. It was found that the effective yield strength is not a function of temperature over the range studied, suggesting that changes in other properties are responsible for differences in rebound behavior. The improved model was incorporated into a computational simulation of an impinging flow to assess the effect of the model improvements on deposition predictions, with the improved model obtaining deposition trends that more closely match what has been observed in previous experiments. The work performed serves as a stepping stone towards further improvement of physics-based impact and deposition models through refinement of other modeled physical processes.


  • The Effect of Gas and Surface Temperature on Cold-Side and Hot-Side Turbine Deposition

    by Jeffrey P. Bons, Chihsiu Lo, Eric Nied, Jiaxuan Han

    Deposition studies were conducted using two impingement jet facilities: a 60 m/s cold jet (830–950 K) impinging on a heated Hastelloy-X surface (1033–1255 K) and a 215 m/s hot jet (1450–1625 K) impinging on an uncooled ceramic target or a cooled thermal barrier coated (TBC) surface (1090–1400 K). These can be considered analogs for an internal impingement cooling jet flow and an external nozzle guide vane leading edge flow respectively. Airflows were seeded with 0–10 µm Arizona road dust and deposition accumulated over a period of 5–10 min. Selected tests were completed with other size distributions. Studies were conducted by varying flow temperature at constant surface temperature and vice-versa. For both hot and cold impingement jets, the sensitivity of capture efficiency to fluid (and thus particle) temperature was found to be roughly double the sensitivity to surface temperature. Hot jet tests with three different size distributions of dust (0–5, 0–10, and 5–10 µm) allowed particle size sensitivity to be evaluated. For both target types (ceramic and cooled TBC), the 0–10 µm test dust produced the highest deposition rate of the three size distributions. Possible explanations for the observed behavior are proposed. Companion CFD studies modeling both impinging jets with particle deposition demonstrate that temperature induced variations in particle trajectories alone are not sufficient to explain observed deposition trends with temperature. Implications for the development of a universal sticking model relevant to gas turbine deposition are discussed.


  • Enhancing Turbine Deposition Prediction Capability With Conjugate Mesh Morphing

    by Christopher P. Bowen, Jeffrey P. Bons

    A framework for performing mesh morphing in a conjugate simulation in the commercial computational fluid dynamics (CFD) software ansys fluent is presented and validated. A procedure for morphing both the fluid and solid domains to simulate the protrusion of deposit into the fluid while concurrently altering and adding to the solid regions is detailed. The ability to delineate between the original metal sections of the solid and the morphed regions which represent deposit characteristics is demonstrated. The validity and predictive capability of the process are tested through simulation of a canonical impingement jet. A single oversized impingement jet (6.35 mm) at 894 K and an average flow velocity of 56.5 m/s is used to heat a nickel-alloy target plate. One gram of 0- to 5-µm Arizona road dust (ARD) is delivered to the target and a Particle Shadow Velocimetry (PSV) technique is used to capture the transient growth of the deposit structure on the target. Thermal infrared images are taken on the backside of the target and synchronized with the PSV images. The experiment is modeled computationally using the Fluent Discrete Phase Model (DPM) and the Ohio State University (OSU) Deposition Model for sticking prediction. The target is morphed according to the particulate volume prediction. The deposit regions are assigned an effective conductivity (keff) representative of a porous deposit, and the fluid and thermal computations are reconverged; 10 mesh morphing iterations are performed accounting for the first half of the experiment. The morphed deposit volume and height are compared to those of the experiment and show reasonable agreement. The backside target temperatures are also compared, and the simulations show the ability to predict the reduction in temperature that occurs as the growing deposit insulates the metal surface. It is demonstrated that the assignment of unique thermal conductivities to the deposit and metal cells within the solid is critical. With a more robust and accurate implementation of the deposit keff, this conjugate mesh morphing framework shows potential as a tool for predicting the thermal impact of deposition.


  • Open Access

    Design of Stress Constrained SiC/SiC Ceramic Matrix Composite Turbine Blades

    by Robert Boyle, Pritheesh Gnanaselvam, Ankur H. Parikh, Ali Ameri, Jeffrey Bons, Vinod K. Nagpal

    While SiC/SiC CMC turbine blades have higher temperature capability than conventional Superalloy turbine blades, cooling CMC blades below their upper use temperature results in smaller strength increases than cooling Superalloy turbine blades. This paper explores the effects on aerodynamic efficiency and stresses for a notional engine where the rpm is held constant and maximum