OMO. Mitrofanov

O. Mitrofanov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


O. Mitrofanov has a total of 7 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    BASE NEUTRAL SURFASE SELECTION FOR OPTIMAL DESIGN OF STRUCTURALLY-ANISOTROPIC AIRCRAFT PANELS MADE FROM COMPOSITE MATERIALS WITH REFINED BUCKLING THEORY RESTRICTIONS

    by L. M. Gavva, O. V. Mitrofanov, V. V. Firsanov

    The aim of this study is the approach to the optimal design of structurally-anisotropic aircraft bearing surface panels with the restrictions according to the refined buckling theory for the optimal size-weight design implementation. The panels are subjected to the distributed constant compressive loading applied to the edges in the skin plane in the longitudinal direction. The panel contour boundary conditions are assumed to be the particular case with conformable boundary restrictions for the plane problem and problem of bending. The optimal design problem statement and analytical solution are formulated to determine the geometry parameters of a flat rectangular multilayer panel made from composite materials with the eccentric longitudinal and lateral stiffening set being of minimal mass. The equal-buckling condition is the optimal design base. The general bending mode of buckling and multi-wave torsion mode of buckling must have the same occurrence probability while the buckling margin tends to one. The optimal design problem is reduced to the mathematic conditional extremum investigation of the goal weight function with multiple variables using the analytical and numerical methods. New mathematic model relations for the buckling problem investigation of structurally-anisotropic composite panels are presented. The primary scientific novelty of this research is the further development of the thin-walled elastic rib theory related to the contact problem for the skin and rib with an improved rib model. The analytical solution is reduced to determine the displacements of a base neutral surface that may be select arbitrarily. The schematization of the panel as structurally-anisotropic one has been proposed as a design model when the critical forces of total bending mode of buckling are determined. For a multi-wave torsion buckling study, one should use the generalized function techniques for the discrete stringer stiffness. The solution of the strained surface differential equation of an eighth order is designed by a trigonometric series in the closed form. The results of the optimal design with the refined buckling restrictions based on refined buckling analysis calculations offer opportunities to reduce and optimize the weight characteristics of aircraft elements.

  • Проектирование гладких композитных панелей при обеспечении устойчивости и прочности при закритическом поведении

    by O. Митрофанов, Московский Авиационный Институт (Национальный Исследовательский Университет), Мазен Осман

    Для сжатых несущих панелей кессонов крыла и агрегатов механизации легкого самолета допускается потеря устойчивости тонких обшивок при нагрузках, близких к эксплуатационному уровню. В работе рассмотрена методика определения оптимальных параметров обшивки из композитных материалов при воздействии сжимающими и сдвиговыми потоками. Особенности постановки задачи оптимального проектирования следующие. Во-первых, при проектировании панелей предложено рассматривать два уровня нагружения: на первом не допускается потеря устойчивости панели; на втором при условии допустимости закритического поведения вычисляют толщину панели из условий достижения предельных по прочности напряжений, определенных с учетом геометрически нелинейных соотношений. Во-вторых, в качестве переменных параметров принята толщина и ширина прямоугольной панели. В-третьих, для определения оптимальных параметров панелей учитывается условие реализации минимальных запасов по устойчивости при первом уровне нагружения и по прочности при проектировании по закритическому состоянию при втором уровне нагружения. Запасы по устойчивости и по прочности на соответствующих уровнях нагружения должны быть равны единице. Указанные уровни нагружения в общем случае не обязательно должны совпадать с эксплуатационными и расчетными нагрузками, рассматриваемыми при проектировании авиационных конструкций, но могут назначаться разработчиком воздушного судна из специальных расчетных условий. Отмечено, что при определении параметров по закритическому состоянию должны быть использованы аналитические решения геометрически нелинейных задач. Указанные соотношения соответствуют методологии проектирования по закритическому состоянию. Приведенные в работе соотношения учитывают мембранные напряжения, возникающие при потере устойчивости тонких панелей. Представленная методика может быть применима на ранних этапах проектирования. В работе приведены соотношения для проектирования шарнирно опертых ортотропных панелей при сжатии, сдвиге и комбинированном нагружении.


  • Open Access

    Post-buckling behavior estimation of composite panels of asymmetric structure with all-boundary rigid support with shear flows action

    by O Mitrofanov, M Osman

    Analytical solution of geometrically non-linear problem of post-buckling behavior of thin rectangular plate of asymmetric structure with shear taking rigid support along all sides into account is obtained. Shown solution can be used for post-buckling behavior estimation of surface defect similar to delamination for composite panels.


  • Open Access

    Analysis of post buckling state of composite rectangular panel with asymmetric structure on elastic base caused biaxial compression

    by O Mitrofanov, M Klesareva

    Received analytical solution of geometrically nonlinear problem for investigation of post buckling of composite rectangular panel with asymmetric structure on elastic base. Panel deflection corresponds to conditions of rigidity support. Considered longitudinal compression of panel subject to constraint along the longitudinal edges which corresponds panel loading caused biaxial compression. Results can be used in the analysis of post buckling thin defects such as delaminations in laminated skins.