Wenjuan Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Wenjuan Sun has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
- Stéphane Chrétien
Université Lumière Lyon 2
4 shared publications Stephen Brown
National Physical Laboratory, Hampton Road, Teddington, TW11 0LW, United Kingdom
3 shared publications- Alan Wilson
Manufacturing & Training Department, National Physical Laboratory, Teddington, UNITED KINGDOM OF GREAT BRITAIN AND NORTHERN IRELAND
2 shared publications - Ander Biguri
Department of Applied Mathematics and Theoretical Physics (DAMTP) University of Cambridge Cambridge UK
2 shared publications - Manuchehr Soleimani
University of Bath
2 shared publications - Mark Noel Mavrogordato
University of Southampton, Engineering and the Environment, Highfield Southampton UK
2 shared publications
Latest Publications
- Open Access
- 27 May 2025
- Published by Elsevier in CIRP Annals
- Vol. 74 (1) , 713-717
Investigation of the correlation between radiographic image quality and surface measurement quality of XCT using frequency response analysis
- 27 May 2025
- Published by Elsevier in CIRP Annals
- Vol. 74 (1) , 713-717
Open AccessInvestigation of the correlation between radiographic image quality and surface measurement quality of XCT using frequency response analysis
- 13 April 2023
- Published by Elsevier in NDT & E International
- Vol. 137
The realisation of fast X-ray computed tomography using a limited number of projection images for dimensional metrology
- 13 April 2023
- Published by Elsevier in NDT & E International
- Vol. 137
The realisation of fast X-ray computed tomography using a limited number of projection images for dimensional metrology
- Open Access
- 12 July 2022
- Published by IOP Publishing in Metrologia
- Vol. 59 (4) , 044003
Effects of fast x-ray cone-beam tomographic measurement on dimensional metrology
X-ray computed tomography (XCT) is increasingly used for dimensional metrology, where it can offer accurate measurements of internal features that are not accessible with other techniques. However, XCT scanning can be relatively slow, which often prevents routine uptake for many applications. This paper explores the feasibility of improving the speed of XCT measurements while maintaining the quality of the dimensional measurements derived from reconstructed volumes. In particular, we compare two approaches to fast XCT acquisition, the use of fewer XCT projections as well as the use of shortened x-ray exposure times for each projection. The study shows that the additional Poisson noise produced by reducing the exposure for each projection has significantly less impact on dimensional measurements compared to the artefacts associated with strategies that take fewer projection images, leading to about half the measurement error variability. Advanced reconstruction algorithms such as the conjugate gradient least squares method or total variation constrained approaches, are shown to allow further improvements in measurement speed, though this can come at the cost of increased measurement bias (e.g. 2.8% increase in relative error in one example) and variance (e.g. 25% in the same example).
- 12 July 2022
- Published by IOP Publishing in Metrologia
- Vol. 59 (4) , 044003
Open AccessEffects of fast x-ray cone-beam tomographic measurement on dimensional metrology
X-ray computed tomography (XCT) is increasingly used for dimensional metrology, where it can offer accurate measurements of internal features that are not accessible with other techniques. However, XCT scanning can be relatively slow, which often prevents routine uptake for many applications. This paper explores the feasibility of improving the speed of XCT measurements while maintaining the quality of the dimensional measurements derived from reconstructed volumes. In particular, we compare two approaches to fast XCT acquisition, the use of fewer XCT projections as well as the use of shortened x-ray exposure times for each projection. The study shows that the additional Poisson noise produced by reducing the exposure for each projection has significantly less impact on dimensional measurements compared to the artefacts associated with strategies that take fewer projection images, leading to about half the measurement error variability. Advanced reconstruction algorithms such as the conjugate gradient least squares method or total variation constrained approaches, are shown to allow further improvements in measurement speed, though this can come at the cost of increased measurement bias (e.g. 2.8% increase in relative error in one example) and variance (e.g. 25% in the same example).
- 9 May 2022
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 33 (8) , 084003
3D roughness standard for performance verification of topography instruments for additively-manufactured surface inspection
The unique complex topography of additively-manufactured surfaces—and the recent rapid evolution of instruments and techniques to measure them—limits trust in inspection data, in direct conflict with the requirements of application areas such as aerospace, where failure of a part can have serious safety consequences. Topography instrument manufacturers and end-users require measurement standards with a controlled reproduction of representative additively-manufactured surfaces to calibrate, performance-verify and intercompare instruments for inspection tasks, thereby improving confidence in measurement. The design of such a surface texture measurement standard is reported, optimised for optical areal topography-measuring instruments and compatible with x-ray computed tomography instruments. Machined from an additively-manufactured blank, the standard’s four sides represent increasing levels of post-processing from the as-deposited surface. Datum features on the measurement standard facilitate direct comparison between topography instruments. Integrated step features support the calibration of an instrument’s Z scale. Calibration of a prototype of the standard is reported; the prototype is matched to a typical aerospace Scalmalloy™ additive manufacturing process. The calibration is also a trial application of a large-area chromatic confocal microscope; this instrument appears capable of calibrating relatively rough measurement standards if required to do so. Reference Ra and S -parameter measurements and associated measurement uncertainties are presented, correlation between parameters noted, and choice and consequences of filter settings discussed.
- 9 May 2022
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 33 (8) , 084003
3D roughness standard for performance verification of topography instruments for additively-manufactured surface inspection
The unique complex topography of additively-manufactured surfaces—and the recent rapid evolution of instruments and techniques to measure them—limits trust in inspection data, in direct conflict with the requirements of application areas such as aerospace, where failure of a part can have serious safety consequences. Topography instrument manufacturers and end-users require measurement standards with a controlled reproduction of representative additively-manufactured surfaces to calibrate, performance-verify and intercompare instruments for inspection tasks, thereby improving confidence in measurement. The design of such a surface texture measurement standard is reported, optimised for optical areal topography-measuring instruments and compatible with x-ray computed tomography instruments. Machined from an additively-manufactured blank, the standard’s four sides represent increasing levels of post-processing from the as-deposited surface. Datum features on the measurement standard facilitate direct comparison between topography instruments. Integrated step features support the calibration of an instrument’s Z scale. Calibration of a prototype of the standard is reported; the prototype is matched to a typical aerospace Scalmalloy™ additive manufacturing process. The calibration is also a trial application of a large-area chromatic confocal microscope; this instrument appears capable of calibrating relatively rough measurement standards if required to do so. Reference Ra and S -parameter measurements and associated measurement uncertainties are presented, correlation between parameters noted, and choice and consequences of filter settings discussed.
- 1 January 2022
- Published by IOP Publishing in Reports on Progress in Physics
- Vol. 85 (1) , 016102
Review of high energy x-ray computed tomography for non-destructive dimensional metrology of large metallic advanced manufactured components
Advanced manufacturing technologies, led by additive manufacturing, have undergone significant growth in recent years. These technologies enable engineers to design parts with reduced weight while maintaining structural and functional integrity. In particular, metal additive manufacturing parts are increasingly used in application areas such as aerospace, where a failure of a mission-critical part can have dire safety consequences. Therefore, the quality of these components is extremely important. A critical aspect of quality control is dimensional evaluation, where measurements provide quantitative results that are traceable to the standard unit of length, the metre. Dimensional measurements allow designers, manufacturers and users to check product conformity against engineering drawings and enable the same quality standard to be used across the supply chain nationally and internationally. However, there is a lack of development of measurement techniques that provide non-destructive dimensional measurements beyond common non-destructive evaluation focused on defect detection. X-ray computed tomography (XCT) technology has great potential to be used as a non-destructive dimensional evaluation technology. However, technology development is behind the demand and growth for advanced manufactured parts. Both the size and the value of advanced manufactured parts have grown significantly in recent years, leading to new requirements of dimensional measurement technologies. This paper is a cross-disciplinary review of state-of-the-art non-destructive dimensional measuring techniques relevant to advanced manufacturing of metallic parts at larger length scales, especially the use of high energy XCT with source energy of greater than 400 kV to address the need in measuring large advanced manufactured parts. Technologies considered as potential high energy x-ray generators include both conventional x-ray tubes, linear accelerators, and alternative technologies such as inverse Compton scattering sources, synchrotron sources and laser-driven plasma sources. Their technology advances and challenges are elaborated on. The paper also outlines the development of XCT for dimensional metrology and future needs.
- 1 January 2022
- Published by IOP Publishing in Reports on Progress in Physics
- Vol. 85 (1) , 016102
Review of high energy x-ray computed tomography for non-destructive dimensional metrology of large metallic advanced manufactured components
Advanced manufacturing technologies, led by additive manufacturing, have undergone significant growth in recent years. These technologies enable engineers to design parts with reduced weight while maintaining structural and functional integrity. In particular, metal additive manufacturing parts are increasingly used in application areas such as aerospace, where a failure of a mission-critical part can have dire safety consequences. Therefore, the quality of these components is extremely important. A critical aspect of quality control is dimensional evaluation, where measurements provide quantitative results that are traceable to the standard unit of length, the metre. Dimensional measurements allow designers, manufacturers and users to check product conformity against engineering drawings and enable the same quality standard to be used across the supply chain nationally and internationally. However, there is a lack of development of measurement techniques that provide non-destructive dimensional measurements beyond common non-destructive evaluation focused on defect detection. X-ray computed tomography (XCT) technology has great potential to be used as a non-destructive dimensional evaluation technology. However, technology development is behind the demand and growth for advanced manufactured parts. Both the size and the value of advanced manufactured parts have grown significantly in recent years, leading to new requirements of dimensional measurement technologies. This paper is a cross-disciplinary review of state-of-the-art non-destructive dimensional measuring techniques relevant to advanced manufacturing of metallic parts at larger length scales, especially the use of high energy XCT with source energy of greater than 400 kV to address the need in measuring large advanced manufactured parts. Technologies considered as potential high energy x-ray generators include both conventional x-ray tubes, linear accelerators, and alternative technologies such as inverse Compton scattering sources, synchrotron sources and laser-driven plasma sources. Their technology advances and challenges are elaborated on. The paper also outlines the development of XCT for dimensional metrology and future needs.
- Open Access
- 19 November 2021
- Published by MDPI AG in Mathematics
- Vol. 9 (22) , 2960
Fast Hyperparameter Calibration of Sparsity Enforcing Penalties in Total Generalised Variation Penalised Reconstruction Methods for XCT Using a Planted Virtual Reference Image
The reconstruction problem in X-ray computed tomography (XCT) is notoriously difficult in the case where only a small number of measurements are made. Based on the recently discovered Compressed Sensing paradigm, many methods have been proposed in order to address the reconstruction problem by leveraging inherent sparsity of the object’s decompositions in various appropriate bases or dictionaries. In practice, reconstruction is usually achieved by incorporating weighted sparsity enforcing penalisation functionals into the least-squares objective of the associated optimisation problem. One such penalisation functional is the Total Variation (TV) norm, which has been successfully employed since the early days of Compressed Sensing. Total Generalised Variation (TGV) is a recent improvement of this approach. One of the main advantages of such penalisation based approaches is that the resulting optimisation problem is convex and as such, cannot be affected by the possible existence of spurious solutions. Using the TGV penalisation nevertheless comes with the drawback of having to tune the two hyperparameters governing the TGV semi-norms. In this short note, we provide a simple and efficient recipe for fast hyperparameters tuning, based on the simple idea of virtually planting a mock image into the model. The proposed trick potentially applies to all linear inverse problems under the assumption that relevant prior information is available about the sought for solution, whilst being very different from the Bayesian method.
- 19 November 2021
- Published by MDPI AG in Mathematics
- Vol. 9 (22) , 2960
Open AccessFast Hyperparameter Calibration of Sparsity Enforcing Penalties in Total Generalised Variation Penalised Reconstruction Methods for XCT Using a Planted Virtual Reference Image
The reconstruction problem in X-ray computed tomography (XCT) is notoriously difficult in the case where only a small number of measurements are made. Based on the recently discovered Compressed Sensing paradigm, many methods have been proposed in order to address the reconstruction problem by leveraging inherent sparsity of the object’s decompositions in various appropriate bases or dictionaries. In practice, reconstruction is usually achieved by incorporating weighted sparsity enforcing penalisation functionals into the least-squares objective of the associated optimisation problem. One such penalisation functional is the Total Variation (TV) norm, which has been successfully employed since the early days of Compressed Sensing. Total Generalised Variation (TGV) is a recent improvement of this approach. One of the main advantages of such penalisation based approaches is that the resulting optimisation problem is convex and as such, cannot be affected by the possible existence of spurious solutions. Using the TGV penalisation nevertheless comes with the drawback of having to tune the two hyperparameters governing the TGV semi-norms. In this short note, we provide a simple and efficient recipe for fast hyperparameters tuning, based on the simple idea of virtually planting a mock image into the model. The proposed trick potentially applies to all linear inverse problems under the assumption that relevant prior information is available about the sought for solution, whilst being very different from the Bayesian method.
- Open Access
- 2 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
FVM and XCT Measurement of Surface Texture of Additively Manufactured Parts
Focus variation microscopy (FVM) and X-ray computed tomography (XCT) are two popular technologies employed to measure the surface texture of additively manufactured components. The impacts of various influence factors of these two measurement techniques on surface texture measurement are investigated, respectively. A two-stage surface registration program is developed to allow the accurate comparison of surface topographies measured by two instruments at the same location on the surface. The associated surface texture parameters Sa, Sq, Ssk, and Sku are also compared. The results indicate XCT can capture re-entrant features, while FVM can capture more details. However, XCT measurement is limited in its resolution and FVM measurement is restricted by the line-of-sight constraint. The surface parameters of two measurement techniques are closer in the cases where surface texture of the parts is higher.
- 2 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Open AccessFVM and XCT Measurement of Surface Texture of Additively Manufactured Parts
Focus variation microscopy (FVM) and X-ray computed tomography (XCT) are two popular technologies employed to measure the surface texture of additively manufactured components. The impacts of various influence factors of these two measurement techniques on surface texture measurement are investigated, respectively. A two-stage surface registration program is developed to allow the accurate comparison of surface topographies measured by two instruments at the same location on the surface. The associated surface texture parameters Sa, Sq, Ssk, and Sku are also compared. The results indicate XCT can capture re-entrant features, while FVM can capture more details. However, XCT measurement is limited in its resolution and FVM measurement is restricted by the line-of-sight constraint. The surface parameters of two measurement techniques are closer in the cases where surface texture of the parts is higher.
- Open Access
Ant Colony-Based Hyperparameter Optimisation in Total Variation Reconstruction in X-ray Computed Tomography
In this paper, a computer-aided training method for hyperparameter selection of limited data X-ray computed tomography (XCT) reconstruction was proposed. The proposed method employed the ant colony optimisation (ACO) approach to assist in hyperparameter selection for the adaptive-weighted projection-controlled steepest descent (AwPCSD) algorithm, which is a total-variation (TV) based regularisation algorithm. During the implementation, there was a colony of artificial ants that swarm through the AwPCSD algorithm. Each ant chose a set of hyperparameters required for its iterative CT reconstruction and the correlation coefficient (CC) score was given for reconstructed images compared to the reference image. A colony of ants in one generation left a pheromone through its chosen path representing a choice of hyperparameters. Higher score means stronger pheromones/probabilities to attract more ants in the next generations. At the end of the implementation, the hyperparameter configuration with the highest score was chosen as an optimal set of hyperparameters. In the experimental results section, the reconstruction using hyperparameters from the proposed method was compared with results from three other cases: the conjugate gradient least square (CGLS), the AwPCSD algorithm using the set of arbitrary hyperparameters and the cross-validation method.The experiments showed that the results from the proposed method were superior to those of the CGLS algorithm and the AwPCSD algorithm using the set of arbitrary hyperparameters. Although the results of the ACO algorithm were slightly inferior to those of the cross-validation method as measured by the quantitative metrics, the ACO algorithm was over 10 times faster than cross—Validation. The optimal set of hyperparameters from the proposed method was also robust against an increase of noise in the data and can be applicable to different imaging samples with similar context. The ACO approach in the proposed method was able to identify optimal values of hyperparameters for a dataset and, as a result, produced a good quality reconstructed image from limited number of projection data. The proposed method in this work successfully solves a problem of hyperparameters selection, which is a major challenge in an implementation of TV based reconstruction algorithms.
Open AccessAnt Colony-Based Hyperparameter Optimisation in Total Variation Reconstruction in X-ray Computed Tomography
In this paper, a computer-aided training method for hyperparameter selection of limited data X-ray computed tomography (XCT) reconstruction was proposed. The proposed method employed the ant colony optimisation (ACO) approach to assist in hyperparameter selection for the adaptive-weighted projection-controlled steepest descent (AwPCSD) algorithm, which is a total-variation (TV) based regularisation algorithm. During the implementation, there was a colony of artificial ants that swarm through the AwPCSD algorithm. Each ant chose a set of hyperparameters required for its iterative CT reconstruction and the correlation coefficient (CC) score was given for reconstructed images compared to the reference image. A colony of ants in one generation left a pheromone through its chosen path representing a choice of hyperparameters. Higher score means stronger pheromones/probabilities to attract more ants in the next generations. At the end of the implementation, the hyperparameter configuration with the highest score was chosen as an optimal set of hyperparameters. In the experimental results section, the reconstruction using hyperparameters from the proposed method was compared with results from three other cases: the conjugate gradient least square (CGLS), the AwPCSD algorithm using the set of arbitrary hyperparameters and the cross-validation method.The experiments showed that the results from the proposed method were superior to those of the CGLS algorithm and the AwPCSD algorithm using the set of arbitrary hyperparameters. Although the results of the ACO algorithm were slightly inferior to those of the cross-validation method as measured by the quantitative metrics, the ACO algorithm was over 10 times faster than cross—Validation. The optimal set of hyperparameters from the proposed method was also robust against an increase of noise in the data and can be applicable to different imaging samples with similar context. The ACO approach in the proposed method was able to identify optimal values of hyperparameters for a dataset and, as a result, produced a good quality reconstructed image from limited number of projection data. The proposed method in this work successfully solves a problem of hyperparameters selection, which is a major challenge in an implementation of TV based reconstruction algorithms.
- Open Access
- 14 December 2020
- Published by IOP Publishing in Metrologia
- Vol. 58 (1) , 015015
Establishing waveguide lines as primary standards for scattering parameter measurements at submillimetre wavelengths
This paper presents a detailed assessment of two rectangular metallic waveguide lines in order that they can be used as primary standards to provide metrological traceability for electrical scattering parameter measurements at submillimetre wavelengths. The assessment comprises a series of dimensional measurements to determine the overall quality of the lines in terms of the waveguide aperture size and alignment. This is followed by electrical measurements to confirm the electrical behaviour of the lines. Finally, the lines are employed as standards to calibrate a vector network analyser which is used to measure devices to verify the performance of the lines as calibration standards, in operando. The waveguide size is WM-380, which operates from 500 GHz to 750 GHz.
- 14 December 2020
- Published by IOP Publishing in Metrologia
- Vol. 58 (1) , 015015
Open AccessEstablishing waveguide lines as primary standards for scattering parameter measurements at submillimetre wavelengths
This paper presents a detailed assessment of two rectangular metallic waveguide lines in order that they can be used as primary standards to provide metrological traceability for electrical scattering parameter measurements at submillimetre wavelengths. The assessment comprises a series of dimensional measurements to determine the overall quality of the lines in terms of the waveguide aperture size and alignment. This is followed by electrical measurements to confirm the electrical behaviour of the lines. Finally, the lines are employed as standards to calibrate a vector network analyser which is used to measure devices to verify the performance of the lines as calibration standards, in operando. The waveguide size is WM-380, which operates from 500 GHz to 750 GHz.