Mayra Agustina Pantoja Castro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mayra Agustina Pantoja Castro has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Ebelia Del Angel Meraz
Universidad Juárez Autónoma de Tabasco
8 shared publications - René Sebastián Mora-Ortiz
División Académica de Ingeniería y Arquitectura (DAIA), Universidad Juárez Autónoma de Tabasco, Carretera Cunduacán-Jalpa de Méndez km. 1, Cunduacán 86690, Tabasco, Mexico
5 shared publications - Francisco Magaña-Hernández
División Académica de Ingeniería y Arquitectura (DAIA), Universidad Juárez Autónoma de Tabasco, Carretera Cunduacán-Jalpa de Méndez km. 1, Cunduacán 86690, Mexico
4 shared publications - Sergio Alberto Diaz
División Académica de Ingeniería y Arquitectura (DAIA), Universidad Juárez Autónoma de Tabasco, Carretera Cunduacán-Jalpa de Méndez km. 1, Cunduacán 86690, Tabasco, Mexico
4 shared publications - Emmanuel Munguía-Balvanera
División Académica de Ingeniería y Arquitectura (DAIA), Universidad Juárez Autónoma de Tabasco, Carretera Cunduacán-Jalpa de Méndez km. 1, Cunduacán 86690, Tabasco, Mexico
3 shared publications - Justino Alavez-Ramírez
Universidad Juárez Autónoma de Tabasco
2 shared publications
Latest Publications
- Open Access
Biochar Synthesized from Post-Consumer Coffee Waste Using Molten Salts for Sodium-Ion Battery Applications
Biochars derived from post-consumer coffee residues were synthesized using NaCl and NaHCO3 as impregnation agents, which were pyrolyzed at 500 and 1000 °C. Structural characterization revealed that NaHCO3 treatment at 1000 °C generated a highly interconnected porous network, with a surface area of 1353.22 m2 g−1, pore volume of 0.83 cm3 g−1, and average pore size of 2.6 nm. These features, confirmed by nitrogen physisorption and SEM, favor Na+ accessibility and insertion. XRD and Raman analyses indicated a predominantly amorphous carbon, with graphitic domains and an interplanar distance of ≈0.34 nm, providing both adsorption capacity and electrical conductivity. Electrochemical evaluation showed that BCNaHCO3-1000°C achieved an initial capacity of 34 mAh g−1, stable for more than 15 cycles, outperforming NaCl-treated biochars. However, despite the favorable morphology, the high surface area may also promote side reactions and irreversible capacity loss, limiting overall efficiency. These findings demonstrate the feasibility of valorizing coffee waste into carbonaceous materials for sodium-ion battery anodes, while highlighting the need for further optimization of porosity, graphitization, and compositional modifications to enhance energy storage performance.
Open AccessBiochar Synthesized from Post-Consumer Coffee Waste Using Molten Salts for Sodium-Ion Battery Applications
Biochars derived from post-consumer coffee residues were synthesized using NaCl and NaHCO3 as impregnation agents, which were pyrolyzed at 500 and 1000 °C. Structural characterization revealed that NaHCO3 treatment at 1000 °C generated a highly interconnected porous network, with a surface area of 1353.22 m2 g−1, pore volume of 0.83 cm3 g−1, and average pore size of 2.6 nm. These features, confirmed by nitrogen physisorption and SEM, favor Na+ accessibility and insertion. XRD and Raman analyses indicated a predominantly amorphous carbon, with graphitic domains and an interplanar distance of ≈0.34 nm, providing both adsorption capacity and electrical conductivity. Electrochemical evaluation showed that BCNaHCO3-1000°C achieved an initial capacity of 34 mAh g−1, stable for more than 15 cycles, outperforming NaCl-treated biochars. However, despite the favorable morphology, the high surface area may also promote side reactions and irreversible capacity loss, limiting overall efficiency. These findings demonstrate the feasibility of valorizing coffee waste into carbonaceous materials for sodium-ion battery anodes, while highlighting the need for further optimization of porosity, graphitization, and compositional modifications to enhance energy storage performance.
- Open Access
Hybrid Mortar Composites Incorporating Oyster Shell Filler and Recycled Fibers from Disposable Masks
This study presents the development of hybrid masonry mortars by incorporating two waste materials: recycled plastic strips from disposable face masks (FM) as mechanical reinforcement and calcined oyster shell powder (OSP) as a filler. The objective was to evaluate the combined effect of FM and OSP on the mechanical behavior of mortars. Three types of mixes were prepared: a reference mix, a mix with 5% OSP (by cement weight), and mixes with 5% OSP reinforced with FM strips. FM strips were incorporated at three different lengths, dividing the FM-reinforced group into three subgroups (0.1%, 0.2%, 0.5%, and 0.8%). The results showed an approximately 10% increase in compressive strength with the addition of 5% OSP compared to the control mortar, as well as an improvement in bond strength of about 21%. Furthermore, an optimum content of 0.2% of 6 mm strips allowed for adequate dispersion and maintained indirect tensile strengths similar to the control + OSP. OSP acted as a reactive filler, increasing compressive strength and improving both density and adhesion. However, higher FM contents or longer strips increased porosity and water absorption, while reducing strength. This combination represents an innovative strategy for valorizing post-pandemic and marine waste.
Open AccessHybrid Mortar Composites Incorporating Oyster Shell Filler and Recycled Fibers from Disposable Masks
This study presents the development of hybrid masonry mortars by incorporating two waste materials: recycled plastic strips from disposable face masks (FM) as mechanical reinforcement and calcined oyster shell powder (OSP) as a filler. The objective was to evaluate the combined effect of FM and OSP on the mechanical behavior of mortars. Three types of mixes were prepared: a reference mix, a mix with 5% OSP (by cement weight), and mixes with 5% OSP reinforced with FM strips. FM strips were incorporated at three different lengths, dividing the FM-reinforced group into three subgroups (0.1%, 0.2%, 0.5%, and 0.8%). The results showed an approximately 10% increase in compressive strength with the addition of 5% OSP compared to the control mortar, as well as an improvement in bond strength of about 21%. Furthermore, an optimum content of 0.2% of 6 mm strips allowed for adequate dispersion and maintained indirect tensile strengths similar to the control + OSP. OSP acted as a reactive filler, increasing compressive strength and improving both density and adhesion. However, higher FM contents or longer strips increased porosity and water absorption, while reducing strength. This combination represents an innovative strategy for valorizing post-pandemic and marine waste.
- Open Access
- 1 October 2025
- Published by Elsevier in Measurement: Sensors
- Vol. 42
Parameter to minimize false alarms in Negative Pressure Wave leak detection systems
- 1 October 2025
- Published by Elsevier in Measurement: Sensors
- Vol. 42
Open AccessParameter to minimize false alarms in Negative Pressure Wave leak detection systems
- Open Access
- 20 December 2024
- Published by National Technological of Mexico / Instituto Tecnológico Villahermosa in Huella Científica
- Vol. 1 (1) , 45-74
Destilación flash: modelado de procesos isotérmicos y adiabáticos en ingeniería de procesos
En este trabajo se presenta el desarrollo y programación de una interfaz gráfica para el modelado y simulación del proceso de separación, destilación flash isotérmica y adiabática, utilizando el software abierto GNU Octave, el trabajo tuvo como propósito la programación de todos los elementos para llevar a cabo el modelado y la simulación de este proceso relevante en la Ingeniería Química, se programó una base de datos completa que incluye propiedades termofísicas de 1650 compuestos junto con las ecuaciones que modelan el flash, las relaciones de equilibrio, los modelos y algoritmos para resolver los problemas no lineales que plantean la solución de la destilación flash. Para el flash adiabático se propuso un algoritmo de solución que facilita la convergencia a la solución buscada. Los resultados obtenidos, con la interfaz grafica programada cuando se comparan con los resultados obtenidos con un simulador de procesos comercial, muestran prácticamente los mismos resultados. La replicación exitosa de los resultados utilizando GNU Octave sugiere una alternativa promisoria para la adopción de herramientas de código abierto en la simulación de procesos químicos. La importancia de estos resultados es particularmente relevante para las instituciones académicas de nivel superior donde el acceso a software comercial costoso puede ser limitado.
- 20 December 2024
- Published by National Technological of Mexico / Instituto Tecnológico Villahermosa in Huella Científica
- Vol. 1 (1) , 45-74
Open AccessDestilación flash: modelado de procesos isotérmicos y adiabáticos en ingeniería de procesos
En este trabajo se presenta el desarrollo y programación de una interfaz gráfica para el modelado y simulación del proceso de separación, destilación flash isotérmica y adiabática, utilizando el software abierto GNU Octave, el trabajo tuvo como propósito la programación de todos los elementos para llevar a cabo el modelado y la simulación de este proceso relevante en la Ingeniería Química, se programó una base de datos completa que incluye propiedades termofísicas de 1650 compuestos junto con las ecuaciones que modelan el flash, las relaciones de equilibrio, los modelos y algoritmos para resolver los problemas no lineales que plantean la solución de la destilación flash. Para el flash adiabático se propuso un algoritmo de solución que facilita la convergencia a la solución buscada. Los resultados obtenidos, con la interfaz grafica programada cuando se comparan con los resultados obtenidos con un simulador de procesos comercial, muestran prácticamente los mismos resultados. La replicación exitosa de los resultados utilizando GNU Octave sugiere una alternativa promisoria para la adopción de herramientas de código abierto en la simulación de procesos químicos. La importancia de estos resultados es particularmente relevante para las instituciones académicas de nivel superior donde el acceso a software comercial costoso puede ser limitado.
- Open Access
Mechanical Behavior of Masonry Mortars Reinforced with Disposable Face Mask Strips
This research presents an experimental analysis of the mechanical behavior of masonry mortars incorporating disposable face masks (FMs) cut into two different sizes. The objective is to provide experimental data contributing to the consolidation of recycling FMs in mortar mixtures. To achieve this, two types of mixtures were prepared: one with strips of 3 × 3 mm and another with strips of 3 × 10 mm. These FM strips were added in different proportions by the volume of mortar (0%, 0.2%, 0.5%, 0.8%, 1.0%, and 1.5%). In all mortars, the dry bulk density, volume of permeable voids, and water absorption, as well as compressive, flexural, and tensile strengths, were evaluated after a 28-day water immersion curing period. Additionally, two essential properties in masonry mortars were analyzed: air content and shear bond strength. The results indicated that, for both strip sizes, adding FMs up to 0.2% positively affected the flexural and tensile strengths; concerning control mortar, increases of 6% and 1.4%, were recorded, respectively, for the longer strips. At this percentage, the density, air content, and compressive and shear bond strengths are not significantly affected. The results demonstrated that incorporating FMs into mortar mixtures is a promising avenue for sustainable recycling and helps reduce microplastic environmental contamination.
Open AccessMechanical Behavior of Masonry Mortars Reinforced with Disposable Face Mask Strips
This research presents an experimental analysis of the mechanical behavior of masonry mortars incorporating disposable face masks (FMs) cut into two different sizes. The objective is to provide experimental data contributing to the consolidation of recycling FMs in mortar mixtures. To achieve this, two types of mixtures were prepared: one with strips of 3 × 3 mm and another with strips of 3 × 10 mm. These FM strips were added in different proportions by the volume of mortar (0%, 0.2%, 0.5%, 0.8%, 1.0%, and 1.5%). In all mortars, the dry bulk density, volume of permeable voids, and water absorption, as well as compressive, flexural, and tensile strengths, were evaluated after a 28-day water immersion curing period. Additionally, two essential properties in masonry mortars were analyzed: air content and shear bond strength. The results indicated that, for both strip sizes, adding FMs up to 0.2% positively affected the flexural and tensile strengths; concerning control mortar, increases of 6% and 1.4%, were recorded, respectively, for the longer strips. At this percentage, the density, air content, and compressive and shear bond strengths are not significantly affected. The results demonstrated that incorporating FMs into mortar mixtures is a promising avenue for sustainable recycling and helps reduce microplastic environmental contamination.
- Open Access
- 25 December 2023
- Published by MDPI AG in Sustainability
- Vol. 16 (1) , 199
The Use of Pre-Wetting to Improve the Mechanical Behavior of Masonry Mortar Elaborated with Crushed Oyster Shell
In this research, the use of the pre-wetting technique is proposed as an ecological alternative to reduce water absorption in waste oyster shells used in the production of masonry mortar as a partial substitute for natural sand. An experimental study was conducted to assess the properties in both the fresh and hardened states of masonry mortars. Two mortar groups were prepared based on a control mixture, with natural aggregate replaced by crushed oyster shell (COS) in varying proportions. In one group, the COS was pre-wetted, while in the other group, the COS was used at its natural moisture content. The experimental results demonstrated that the pre-wetting process aided in reducing the water–cement ratio (w/c) in the mortar mixture, thereby improving its properties. In both mortar groups, favorable results were observed with respect to capillary water absorption. Although the compressive strength was affected by the incorporation of COS, pre-wetted mortars with substitutions of up to 30% achieved the reference value established in this research. The pre-wetting process proves to be a straightforward and cost-effective technique; it is environmentally friendly and will contribute to decreasing the accumulation of COS in landfills, thereby safeguarding natural material reserves.
- 25 December 2023
- Published by MDPI AG in Sustainability
- Vol. 16 (1) , 199
Open AccessThe Use of Pre-Wetting to Improve the Mechanical Behavior of Masonry Mortar Elaborated with Crushed Oyster Shell
In this research, the use of the pre-wetting technique is proposed as an ecological alternative to reduce water absorption in waste oyster shells used in the production of masonry mortar as a partial substitute for natural sand. An experimental study was conducted to assess the properties in both the fresh and hardened states of masonry mortars. Two mortar groups were prepared based on a control mixture, with natural aggregate replaced by crushed oyster shell (COS) in varying proportions. In one group, the COS was pre-wetted, while in the other group, the COS was used at its natural moisture content. The experimental results demonstrated that the pre-wetting process aided in reducing the water–cement ratio (w/c) in the mortar mixture, thereby improving its properties. In both mortar groups, favorable results were observed with respect to capillary water absorption. Although the compressive strength was affected by the incorporation of COS, pre-wetted mortars with substitutions of up to 30% achieved the reference value established in this research. The pre-wetting process proves to be a straightforward and cost-effective technique; it is environmentally friendly and will contribute to decreasing the accumulation of COS in landfills, thereby safeguarding natural material reserves.
- 1 January 2022
- Published by Instituto Mexicano de Tecnologia del Agua in Tecnología y ciencias del agua
- Vol. 13 (1) , 144-183
Treatment of domestic wastewater using activated carbon prepared from sugarcane bagasse
- 1 January 2022
- Published by Instituto Mexicano de Tecnologia del Agua in Tecnología y ciencias del agua
- Vol. 13 (1) , 144-183
Treatment of domestic wastewater using activated carbon prepared from sugarcane bagasse
- Open Access
Effect of Pre-Wetting Recycled Mortar Aggregate on the Mechanical Properties of Masonry Mortar
In this research we evaluated the use of recycled fine mortar aggregate (RFMA) as a fine aggregate for new masonry mortar creation. The pre-wetting effect on the aggregate before creating the mixture was analyzed as a method to reduce its absorption potential. A control mixture of conventional mortar and two groups of recycled mortars were designed with a partial replacement of natural sand by RFMA (pre-wetted and not pre-wetted) performed in different proportions. The results established that the pre-wetting process allows a reduction in the amount of water required during the creation of new mixtures, regulating the water/cement (W/C) ratio and improving the properties of recycled mortars such as air content, fresh and hardened densities, and compressive and adhesive strength for all substitution levels. Mortar made with a 20% substitution and pre-wetted until it was at 67% of its absorption capacity displayed adhesive values higher than the ones shown by the reference mortar. The pre-wetting process proves to be an easy performance technique; it is inexpensive, environmentally friendly, and the most valuable fact is that specialized equipment is not necessarily needed. This process is the most profitable option for improving RFMA exploitation and reuse.
Open AccessEffect of Pre-Wetting Recycled Mortar Aggregate on the Mechanical Properties of Masonry Mortar
In this research we evaluated the use of recycled fine mortar aggregate (RFMA) as a fine aggregate for new masonry mortar creation. The pre-wetting effect on the aggregate before creating the mixture was analyzed as a method to reduce its absorption potential. A control mixture of conventional mortar and two groups of recycled mortars were designed with a partial replacement of natural sand by RFMA (pre-wetted and not pre-wetted) performed in different proportions. The results established that the pre-wetting process allows a reduction in the amount of water required during the creation of new mixtures, regulating the water/cement (W/C) ratio and improving the properties of recycled mortars such as air content, fresh and hardened densities, and compressive and adhesive strength for all substitution levels. Mortar made with a 20% substitution and pre-wetted until it was at 67% of its absorption capacity displayed adhesive values higher than the ones shown by the reference mortar. The pre-wetting process proves to be an easy performance technique; it is inexpensive, environmentally friendly, and the most valuable fact is that specialized equipment is not necessarily needed. This process is the most profitable option for improving RFMA exploitation and reuse.
- 30 January 2021
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 32 (4) , 4872-4884
Activated carbons from coconut shell and NiO-based composites for energy storage systems
- 30 January 2021
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 32 (4) , 4872-4884
Activated carbons from coconut shell and NiO-based composites for energy storage systems
- 11 January 2021
- Published by The Electrochemical Society in ECS Transactions
- Vol. 101 (1) , 433-447
Use of Coffee Beans to Obtain Activated Carbon with Potential Applications as Supercapacitors
Activated carbons (AC) from coffee bean waste were prepared by chemical activation using as activating compounds potassium hydroxide (KOH) and potassium carbonate (K2CO3) respectively, impregnation times of 24 and 48 hours, 600°C and 700°C as temperatures calcination. After that coals samples were synthesized. They were doped with nickel oxide (NiO) in order to modify the electrical properties of the AC. Later they were characterized (physical adsorption of using N2, FT-IR, XRD). The AC/NiO composites were prepared by the chemical method and the electrodes were compacted into pellet forms, which were placed in a two-electrode cell using 2M sulfuric acid (H2SO4) as electrolyte. Activity electrochemical was evaluated by cyclic voltammetry and galvanostatic chronopotentiometry. Finally, the specific capacitance of the supercapacitors (SCS) was determined from AC/NiO. Results of AC/NiO-48-700°C-KOH and AC/NiO-48-700°C-K2CO3 materials showed maximum capacitances of 405.40 and 394.73 F/g respectively.
- 11 January 2021
- Published by The Electrochemical Society in ECS Transactions
- Vol. 101 (1) , 433-447
Use of Coffee Beans to Obtain Activated Carbon with Potential Applications as Supercapacitors
Activated carbons (AC) from coffee bean waste were prepared by chemical activation using as activating compounds potassium hydroxide (KOH) and potassium carbonate (K2CO3) respectively, impregnation times of 24 and 48 hours, 600°C and 700°C as temperatures calcination. After that coals samples were synthesized. They were doped with nickel oxide (NiO) in order to modify the electrical properties of the AC. Later they were characterized (physical adsorption of using N2, FT-IR, XRD). The AC/NiO composites were prepared by the chemical method and the electrodes were compacted into pellet forms, which were placed in a two-electrode cell using 2M sulfuric acid (H2SO4) as electrolyte. Activity electrochemical was evaluated by cyclic voltammetry and galvanostatic chronopotentiometry. Finally, the specific capacitance of the supercapacitors (SCS) was determined from AC/NiO. Results of AC/NiO-48-700°C-KOH and AC/NiO-48-700°C-K2CO3 materials showed maximum capacitances of 405.40 and 394.73 F/g respectively.