Ahmet Oğuz Demi̇rİz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ahmet Oğuz Demi̇rİz has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Fatih İrfan Baş
Department of Civil Engineering, Faculty of Engineering and Architecture, Erzincan Binali Yıldırım University, Erzincan 24002, Türkiye
2 shared publications - Muhammed Ali Çolak
Erzincan Binali Yıldırım Univ
2 shared publications - Ömer Faruk Keleş
Department of Civil Engineering, Faculty of Engineering and Architecture, Erzincan Binali Yıldırım University, Erzincan 24002, Türkiye
2 shared publications - Halim Ferit Bayata
Erzincan Binali Yildirim Universitesi
1 shared publication - Osman Ünsal Bayrak
Department of Civil Engineering, Ataturk University, Erzurum 25240, Turkey
1 shared publication
Latest Publications
- Open Access
Assessment of Low-Temperature Fracture Behavior in Bituminous Mixtures Incorporating Sustainable Waste Additives: SCB Testing and Finite Element Analysis
In this study, the combined effect of waste lubricating oil (WLO) and waste pine branch ash (WPBA) was investigated to improve the low-temperature fracture behavior of asphalt mixtures. To investigate the low-temperature fracture behavior of the mixtures containing 2%–6% WLO and 3%–12% WPBA, the semi-circular bending (SCB) test was conducted at −15 °C, and the experimental results were analyzed using a statistical approach. Fracture toughness (K(IC)), total fracture energy (GF) and its pre-peak and post-peak components, crack resistance index (CRI), flexibility index (FI), and toughness index (TI) were determined. The findings indicate that the optimal combination depends on the fracture parameter under consideration. The best fracture toughness results, K(IC) = 24.96 MPa·mm0.5, indicating increased resistance to crack initiation, was obtained at 4% WLO and 12% WPBA content. On the other hand, the best fracture energy results, GF = 1.202 N/mm, reflecting an increase in energy dissipation during crack propagation, was obtained at 4% WLO and 9% WPBA content. The highest FI, CRI, and TI values were obtained with 6% WLO and 9% WPBA, corresponding to increases of approximately 66%, 69%, and 16%, respectively, compared with the reference mixture. This resulted in greater crack-initiation resistance, improved post-peak deformation capacity, and higher energy-dissipation capacity, although the greater WLO content led to a decrease in structural integrity. When the results are evaluated overall, it is understood that the use of WLO in the mixtures increases deformation capacity, while the use of WPBA controls crack propagation through its hardening and filling effects. In mixtures containing 4% WLO and 9%–12% WPBA, a balanced behavior was achieved in terms of crack initiation, crack propagation, and stiffness under low-temperature conditions.
Open AccessAssessment of Low-Temperature Fracture Behavior in Bituminous Mixtures Incorporating Sustainable Waste Additives: SCB Testing and Finite Element Analysis
In this study, the combined effect of waste lubricating oil (WLO) and waste pine branch ash (WPBA) was investigated to improve the low-temperature fracture behavior of asphalt mixtures. To investigate the low-temperature fracture behavior of the mixtures containing 2%–6% WLO and 3%–12% WPBA, the semi-circular bending (SCB) test was conducted at −15 °C, and the experimental results were analyzed using a statistical approach. Fracture toughness (K(IC)), total fracture energy (GF) and its pre-peak and post-peak components, crack resistance index (CRI), flexibility index (FI), and toughness index (TI) were determined. The findings indicate that the optimal combination depends on the fracture parameter under consideration. The best fracture toughness results, K(IC) = 24.96 MPa·mm0.5, indicating increased resistance to crack initiation, was obtained at 4% WLO and 12% WPBA content. On the other hand, the best fracture energy results, GF = 1.202 N/mm, reflecting an increase in energy dissipation during crack propagation, was obtained at 4% WLO and 9% WPBA content. The highest FI, CRI, and TI values were obtained with 6% WLO and 9% WPBA, corresponding to increases of approximately 66%, 69%, and 16%, respectively, compared with the reference mixture. This resulted in greater crack-initiation resistance, improved post-peak deformation capacity, and higher energy-dissipation capacity, although the greater WLO content led to a decrease in structural integrity. When the results are evaluated overall, it is understood that the use of WLO in the mixtures increases deformation capacity, while the use of WPBA controls crack propagation through its hardening and filling effects. In mixtures containing 4% WLO and 9%–12% WPBA, a balanced behavior was achieved in terms of crack initiation, crack propagation, and stiffness under low-temperature conditions.
- 28 February 2026
- Published by Raw Data Library
INVESTIGATION OF THE PERFORMANCE OF BITUMEN AND BITUMINOUS MIXTURES MODIFIED WITH GRAPHENE AND HEMP OIL
Purpose: The aim is to develop advanced modified bitumen and bituminous mixtures by incorporating graphene and hemp oil into bitumen to create next-generation asphalt binders. By optimizing the amount of additives, the objective is to prevent unnecessary or excessive use and design bituminous hot mixtures that enhance performance and reduce crack formation. Method: Using the Taguchi optimization method, an experimental plan consisting of 4 parameters with 4 levels was prepared. In accordance with this plan, the physical, chemical, and mechanical properties of bitumen and bituminous mixtures produced with 16 different combinations were examined. Findings: The average values of the elastic recovery ranged from 5% to 12.50%. The average mass loss values from the RTFOT mass loss test ranged from 27.02‱ to 57.48‱. While the softening point of pure bitumen was 45.50°C, the average values from the tests ranged from 43.90°C to 48.40°C. The penetration value of pure bitumen was 90.8, while the average penetration values from the tests ranged from 79.03 to 140.07. Marshall stability values ranged from 911 kg to 1178 kg. In the SCB tests, fracture toughness values ranged from 16.75 to 29.45 MPa√m. In the SENB tests, fracture toughness values ranged from 22.34 to 31.33 MPa√m. Results: As a result of MRPI optimization, the optimum parameter levels were found to be "A2, B2, C4, D2." In MRPI optimization, the most significant contributions were from graphene nanoplatelets at 42.43% and hemp seed oil at 28.75%. In the confirmation tests based on the MRPI optimum parameter levels, the results showed an increase of 14.4% in penetration, 27.33% in penetration after RTFOT, 4.62% in softening point, 4.53% in softening point after RTFOT, 4.83% in stability, 3.43% in SENB fracture toughness at -20°C, 18.03% in SCB fracture toughness at 0°C, and 50.84% in SCB fracture toughness at -20°C. Keywords: GNP, Hemp Seed Oil, SCB, SENB, Marshall, Taguchi Method
- 28 February 2026
- Published by Raw Data Library
INVESTIGATION OF THE PERFORMANCE OF BITUMEN AND BITUMINOUS MIXTURES MODIFIED WITH GRAPHENE AND HEMP OIL
Purpose: The aim is to develop advanced modified bitumen and bituminous mixtures by incorporating graphene and hemp oil into bitumen to create next-generation asphalt binders. By optimizing the amount of additives, the objective is to prevent unnecessary or excessive use and design bituminous hot mixtures that enhance performance and reduce crack formation. Method: Using the Taguchi optimization method, an experimental plan consisting of 4 parameters with 4 levels was prepared. In accordance with this plan, the physical, chemical, and mechanical properties of bitumen and bituminous mixtures produced with 16 different combinations were examined. Findings: The average values of the elastic recovery ranged from 5% to 12.50%. The average mass loss values from the RTFOT mass loss test ranged from 27.02‱ to 57.48‱. While the softening point of pure bitumen was 45.50°C, the average values from the tests ranged from 43.90°C to 48.40°C. The penetration value of pure bitumen was 90.8, while the average penetration values from the tests ranged from 79.03 to 140.07. Marshall stability values ranged from 911 kg to 1178 kg. In the SCB tests, fracture toughness values ranged from 16.75 to 29.45 MPa√m. In the SENB tests, fracture toughness values ranged from 22.34 to 31.33 MPa√m. Results: As a result of MRPI optimization, the optimum parameter levels were found to be "A2, B2, C4, D2." In MRPI optimization, the most significant contributions were from graphene nanoplatelets at 42.43% and hemp seed oil at 28.75%. In the confirmation tests based on the MRPI optimum parameter levels, the results showed an increase of 14.4% in penetration, 27.33% in penetration after RTFOT, 4.62% in softening point, 4.53% in softening point after RTFOT, 4.83% in stability, 3.43% in SENB fracture toughness at -20°C, 18.03% in SCB fracture toughness at 0°C, and 50.84% in SCB fracture toughness at -20°C. Keywords: GNP, Hemp Seed Oil, SCB, SENB, Marshall, Taguchi Method
- 2 February 2021
- Published by Springer Nature in Sādhanā
- Vol. 46 (1) , 1-12
Corridor capacity analysis with mesoscopic simulation: Erzincan province sample
- 2 February 2021
- Published by Springer Nature in Sādhanā
- Vol. 46 (1) , 1-12
Corridor capacity analysis with mesoscopic simulation: Erzincan province sample