Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ömer Faruk Keleş has a total of 3 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Assessment of Low-Temperature Fracture Behavior in Bituminous Mixtures Incorporating Sustainable Waste Additives: SCB Testing and Finite Element Analysis

    by Ömer Faruk Keleş, Muhammed Ali Çolak, Ahmet Oğuz Demiriz, Fatih İrfan Baş

    In this study, the combined effect of waste lubricating oil (WLO) and waste pine branch ash (WPBA) was investigated to improve the low-temperature fracture behavior of asphalt mixtures. To investigate the low-temperature fracture behavior of the mixtures containing 2%–6% WLO and 3%–12% WPBA, the semi-circular bending (SCB) test was conducted at −15 °C, and the experimental results were analyzed using a statistical approach. Fracture toughness (K(IC)), total fracture energy (GF) and its pre-peak and post-peak components, crack resistance index (CRI), flexibility index (FI), and toughness index (TI) were determined. The findings indicate that the optimal combination depends on the fracture parameter under consideration. The best fracture toughness results, K(IC) = 24.96 MPa·mm0.5, indicating increased resistance to crack initiation, was obtained at 4% WLO and 12% WPBA content. On the other hand, the best fracture energy results, GF = 1.202 N/mm, reflecting an increase in energy dissipation during crack propagation, was obtained at 4% WLO and 9% WPBA content. The highest FI, CRI, and TI values were obtained with 6% WLO and 9% WPBA, corresponding to increases of approximately 66%, 69%, and 16%, respectively, compared with the reference mixture. This resulted in greater crack-initiation resistance, improved post-peak deformation capacity, and higher energy-dissipation capacity, although the greater WLO content led to a decrease in structural integrity. When the results are evaluated overall, it is understood that the use of WLO in the mixtures increases deformation capacity, while the use of WPBA controls crack propagation through its hardening and filling effects. In mixtures containing 4% WLO and 9%–12% WPBA, a balanced behavior was achieved in terms of crack initiation, crack propagation, and stiffness under low-temperature conditions.

  • Open Access

    Effects of maximum aggregate grain size and gradation on roller compacted concrete pavements

    by Ömer Faruk Keleş

    Roller compacted concrete (RCC) pavements, which stand out as an alternative to conventional concrete and asphalt pavements, are increasingly preferred because of their high strength, fast construction, and low cost advantages. The properties of aggregates directly affect the performance in roller compacted concrete mixtures. In particular, the maximum aggregate particle size (Dmax) and gradation play a determining influence on the mixture's density, compressibility, and mechanical strength. This study aimed to investigate the effects of maximum aggregate particle size and gradation on the mechanical performance of roller compacted concrete pavement mixtures. Within this scope, roller compacted concrete pavement mixtures were produced using three Dmax (12.5, 19, and 25 mm) and three different cement dosages (300, 350, and 400 kg). Tests for physical properties on mixtures were conducted using unit weight and ultrasonic pulse velocity (UPV) tests, while tests for mechanical properties were conducted using compressive strength, flexural strength, and splitting tensile strength tests. Increasing the Dmax to 25 mm significantly improved the compressive and flexural strength of the mixtures. However, the splitting tensile strength increased up to 19 mm and showed a slight decrease when reaching 25 mm. The increase in cement content consistently improved all mechanical properties. Overall, the use of well-graded coarse aggregates with Dmax in the range of 19–25 mm was found to improve the mechanical properties and compressibility of roller compacted concrete mixtures.

  • Research of Curing Type and Application Time on Roller Compacted Concrete Pavements

    by Ömer Faruk Keleş

    Due to the very dry consistency of roller compacted concrete (RCC) pavements the curing of RCC compared to conventional concretes, requires much more attention and important. In this thesis, the most suitable type of curing and application time for RCC pavements were researched and strenght properties of RCC were investigated. Within the scope of the study, a mixture with standards of 350 kg cement dosage was prepared according to optimum moisture contents as a result of the modified proctor test. It was applied to this mixture 15, 30, 60 min. and immediately after casting in four different time periods four different cures consisting of chemical curing, burlap, membrane and water were applied for 7 days. On the cured samples, experiments like uniaxial compression test, flexural strength test, ultrasonic pulse velocity test and schmidt rebound hammer test were carried out Based on the results obtained, water cure technique has been determined as the most suitable curing method for RCC. This method followed the membrane cure. For water cure technique the best application time was 60 min. after casting has been determined. The time period for which compressive strength for opening to public traffic was found to be seven hours.

  • Investigation of The Performance of Roller Compacted Concrete (RCC) Pavements Containing Waste Rubber

    by Ömer Faruk Keleş

    Purpose: In this study, in order to produce sustainable roller compacted concrete (RCC) pavements, waste rubber tyres of different sizes, which pollute the environment and cannot be disposed of sufficiently every year, were used as coarse and fine aggregate substitutes to investigate the effects of waste rubber on the mechanical, durability and thermal properties of RCC pavements. Method: Waste rubber in three different sizes (shredded, crumb and powder) was replaced by aggregate at six levels (2.5%, 5%, 7.5%, 10%, 20% and 30%) with a maximum of 30% in SSB mixtures. The compressive, flexural and splitting tensile strengths as well as UPV, unit weight and modulus of elasticity were determined and compared with each other in order to investigate the mechanical properties of the SSB pavement mixtures with waste rubber composition. In order to determine the durability properties of SSB pavement mixtures containing waste rubber, the specimens were subjected to elevated temperature, freeze thaw, acid and sulphate effects. In addition, microstructural analysis was performed using scanning electron microscopy (SEM) to investigate the physical structure of SSB with waste rubber and its effect on concrete properties. In addition, using outdoor temperature data, modeling was performed by finite element analysis using the 3D software package ANSYS. With these models, the effects of waste rubber tires on the stresses caused by temperature changes in SSB pavements were investigated. Findings: In SSB specimens with 30% waste rubber content, 81%, 60% and 74% strength loss occurred in compressive, flexural and splitting tensile strengths, respectively, when compared to control specimens without waste rubber. Although it caused a decrease in strength, a mixture with a flexural strength of 4,96 MPa was obtained with the use of 20% waste rubber, making it possible to use them in pavements. In mixtures with 30% waste rubber content, 62%, 71% and 97% loss occurred in compressive, splitting tensile and flexural strengths after elevated temperature. In mixtures containing 30% waste rubber, a 21% loss in compressive strength occurred after 300 cycles of freeze thawing. After 180 days of acid effect, compressive strength loss was 55% in 30% waste tire-containing specimens, while compressive strength loss was 18% in 30% waste tire-containing specimens after 180 days of sulfate effect. With the partial replacement of coarse and fine aggregate with waste tires, a significant decrease of approximately 90% in the modulus of elasticity was determined. Results: The use of waste rubber in SSB instead of aggregate had a negative effect on the mechanical and durability properties of the mixtures. The increase in the amount of waste rubber resulted in the need for more water for the mixture and resulted in a 15% lighter mixture due to its low specific gravity and hollow structure. From a thermal point of view, the finite element analysis results show that the stresses in the pavement layer due to temperature differences decrease with increasing waste rubber content. Keywords: Roller compacted concrete, waste rubber, mechanical properties, durability properties, thermal analysis, finite element method.