Nishant Tiwari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Nishant Tiwari has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
Indra Kumar Lokhande
5 shared publicationsAbhishek Sharma
B I T Sindri
2 shared publications- Abhishek Sharma
Department of Mechanical Engineering, Government Engineering College Palamu (Department of Higher and Technical Education, Govt. of Jharkhand), Medininagar, India
2 shared publications - Manoj Kumar Moharana
Thermal Systems Laboratory, Department of Mechanical Engineering, National Institute of Technology Rourkela, Rourkela, India
2 shared publications Advait Mishra
School of Mechanical Engineering Vellore Institute of Technology Vellore India
1 shared publication- Anil Singh Yadav
Bakhtiyarpur College of Engineering
1 shared publication
Latest Publications
- 29 November 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 285
Experimental and numerical study of automated hybrid PCM and liquid cooling for high capacity Lithium-Ion pouch cell
- 29 November 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 285
Experimental and numerical study of automated hybrid PCM and liquid cooling for high capacity Lithium-Ion pouch cell
- Open Access
- 26 August 2025
- Published by Elsevier in Results in Engineering
- Vol. 27
Numerical investigation of PCM-filled pin-fin microchannels for thermal management of HCPV cell
- 26 August 2025
- Published by Elsevier in Results in Engineering
- Vol. 27
Open AccessNumerical investigation of PCM-filled pin-fin microchannels for thermal management of HCPV cell
- 7 January 2024
- Published by Springer Nature
- p. 457-469
Numerical Study of Combined Phase Change Material and Natural Air Cooling System for Lithium-Ion Battery Thermal Management
- 7 January 2024
- Published by Springer Nature
- p. 457-469
Numerical Study of Combined Phase Change Material and Natural Air Cooling System for Lithium-Ion Battery Thermal Management
- 15 November 2023
- Published by Springer Nature
- p. 209-233
A Review on Fast Charging/Discharging Effect in Lithium-Ion Batteries for Electric Vehicles
- 15 November 2023
- Published by Springer Nature
- p. 209-233
A Review on Fast Charging/Discharging Effect in Lithium-Ion Batteries for Electric Vehicles
- 2 August 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 239 (4) , 1892-1901
Experimental analysis of a diesel engine run on non-conventional fuel blend at different preheating temperatures
Due to urbanisation, the reuse of scrap tyres in the form of energy has gained attention for the disposal of waste tyres. Among the numerous methods, pyrolysis appears to be possible, appealing and viable for generating products such as pyrolysis oil, which can be combined with petroleum oils and used as a source of energy. In a prior study, a mixture of jatropha methyl ester (JME) and tyre pyrolysis oil (TPO) was used as a diesel engine fuel, and it was discovered that the JMETPO20 (JME80% + TPO20%) blend gave better results among all the test blends but inferior than diesel operation. Also, it was reported that due to higher viscosity of the JMETPO20 blend, engine gave inferior performance than diesel operated engine. In this context, an attempt has been made to utilize the JMETPO20 blend at different preheating temperatures to substitute conventional diesel. The blend was preheated at three different temperatures, that is, 50, 60 and 70°C and experiments were carried out in a single-cylinder diesel engine with a rated output of 4.4 kW. The results of the investigations were analysed and compared with diesel and presented in this study.
- 2 August 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 239 (4) , 1892-1901
Experimental analysis of a diesel engine run on non-conventional fuel blend at different preheating temperatures
Due to urbanisation, the reuse of scrap tyres in the form of energy has gained attention for the disposal of waste tyres. Among the numerous methods, pyrolysis appears to be possible, appealing and viable for generating products such as pyrolysis oil, which can be combined with petroleum oils and used as a source of energy. In a prior study, a mixture of jatropha methyl ester (JME) and tyre pyrolysis oil (TPO) was used as a diesel engine fuel, and it was discovered that the JMETPO20 (JME80% + TPO20%) blend gave better results among all the test blends but inferior than diesel operation. Also, it was reported that due to higher viscosity of the JMETPO20 blend, engine gave inferior performance than diesel operated engine. In this context, an attempt has been made to utilize the JMETPO20 blend at different preheating temperatures to substitute conventional diesel. The blend was preheated at three different temperatures, that is, 50, 60 and 70°C and experiments were carried out in a single-cylinder diesel engine with a rated output of 4.4 kW. The results of the investigations were analysed and compared with diesel and presented in this study.
- 26 May 2023
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 43 (2)
Effect of piston bowl geometry and spray angle on engine performance and emissions in HCCI engine using multi‐stage injection strategy
The homogeneous charge compression ignition (HCCI) and combustion chamber geometry play significant roles in improving the potential of compression ignition engines and their environmental sustainability. However, a major hindrance to the progress of HCCI technology has been the notable decline in brake thermal efficiency and emit high levels of hydrocarbon (HC) and carbon monoxide (CO) which is mainly due to the low temperatures during combustion and low post oxidation of these components. Combustion chambers like hemispherical combustion chamber (TCC) and toroidal combustion chamber (TCC) are known to provide better combustion characteristics due to their increased surface‐to‐volume ratio. Moreover, injection timing and spray position have shown a significant effect on the controlling onset of combustion and emission in HCCI engine. Therefore, the primary objective of this numerical study is to enhance the engine characteristics in HCCI mode using an HCC and TCC piston bowl geometry coupled with multistage injection and compare the results with flat piston bowl geometry. The results show that the toroidal shape piston geometry provides 3%–5% higher brake thermal efficiency compared to the conventional piston geometry. Additionally, the energy balance analysis revealed that the combination of modified piston geometry and multi stage injection improved the combustion process by reducing the energy losses due to incomplete combustion and heat transfer to the engine walls. These findings suggest that the proposed injection strategy combined with modified piston geometry has the potential to enhance the performance of HCCI engines and reduce their environmental impact.
- 26 May 2023
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 43 (2)
Effect of piston bowl geometry and spray angle on engine performance and emissions in HCCI engine using multi‐stage injection strategy
The homogeneous charge compression ignition (HCCI) and combustion chamber geometry play significant roles in improving the potential of compression ignition engines and their environmental sustainability. However, a major hindrance to the progress of HCCI technology has been the notable decline in brake thermal efficiency and emit high levels of hydrocarbon (HC) and carbon monoxide (CO) which is mainly due to the low temperatures during combustion and low post oxidation of these components. Combustion chambers like hemispherical combustion chamber (TCC) and toroidal combustion chamber (TCC) are known to provide better combustion characteristics due to their increased surface‐to‐volume ratio. Moreover, injection timing and spray position have shown a significant effect on the controlling onset of combustion and emission in HCCI engine. Therefore, the primary objective of this numerical study is to enhance the engine characteristics in HCCI mode using an HCC and TCC piston bowl geometry coupled with multistage injection and compare the results with flat piston bowl geometry. The results show that the toroidal shape piston geometry provides 3%–5% higher brake thermal efficiency compared to the conventional piston geometry. Additionally, the energy balance analysis revealed that the combination of modified piston geometry and multi stage injection improved the combustion process by reducing the energy losses due to incomplete combustion and heat transfer to the engine walls. These findings suggest that the proposed injection strategy combined with modified piston geometry has the potential to enhance the performance of HCCI engines and reduce their environmental impact.
- 5 July 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 238 (1) , 124-133
Experimental analysis of latent heat thermal energy storage system using encapsulated multiple phase-change materials
The current study aims to improve the energy storage capability of the thermal energy storage system by utilizing multiple phase-change materials. In this regard, a new thermal energy storage system has been studied when multiple phase-change material with different melting temperatures are employed. In this study, three-set, each having 70 encapsulated phase-change materials, are arranged horizontally in the order of decreasing melting temperature for the charging cycle and increasing melting temperature in the case of discharging cycle. Water is employed as heat transfer fluid, and the SAE 304 spherical capsule with a diameter of 60 cm is used to encapsulate the phase-change material. The arrangement showed an excellent thermal response for input parameters such as inlet temperature, flow rate. Further, it was observed that as the heat transfer fluid flow rate increases from 1 litres per minute (LPM) to 5 LPM, the melting and solidification time decreases from 10% to 30% and 14% to 28%, respectively. It was also noticed that as the flow rate increases, exergy and overall efficiency decreases.
- 5 July 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 238 (1) , 124-133
Experimental analysis of latent heat thermal energy storage system using encapsulated multiple phase-change materials
The current study aims to improve the energy storage capability of the thermal energy storage system by utilizing multiple phase-change materials. In this regard, a new thermal energy storage system has been studied when multiple phase-change material with different melting temperatures are employed. In this study, three-set, each having 70 encapsulated phase-change materials, are arranged horizontally in the order of decreasing melting temperature for the charging cycle and increasing melting temperature in the case of discharging cycle. Water is employed as heat transfer fluid, and the SAE 304 spherical capsule with a diameter of 60 cm is used to encapsulate the phase-change material. The arrangement showed an excellent thermal response for input parameters such as inlet temperature, flow rate. Further, it was observed that as the heat transfer fluid flow rate increases from 1 litres per minute (LPM) to 5 LPM, the melting and solidification time decreases from 10% to 30% and 14% to 28%, respectively. It was also noticed that as the flow rate increases, exergy and overall efficiency decreases.
- 4 February 2021
- Published by Springer Nature in Sādhanā
- Vol. 46 (1) , 1-12
Effect of conjugate heat transfer in single-phase laminar flow through partially heated microtubes
- 4 February 2021
- Published by Springer Nature in Sādhanā
- Vol. 46 (1) , 1-12
Effect of conjugate heat transfer in single-phase laminar flow through partially heated microtubes