Samir Kumar Acharya
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Samir Kumar Acharya has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Smitirupa Pradhan
School of Mechanical Engineering, National Institute of Science and Technology, Odisha, India
3 shared publications - Ved Prakash
Department of Mechanical Engineering, National Institute of Technology Rourkela, Rourkela, India
3 shared publications - Prajapati Naik
Faculty of Engineering and Technology, Jadavpur University, Kolkata, India
2 shared publications - Prasanta Sahoo
Department of Mechanical Engineering, Jadavpur University, Kolkata, India
2 shared publications Subhrajit Pradhan
Department of Mechanical Engineering, National Institute of Technology, Rourkela, India
2 shared publications- Subhrajit Pradhan
Department of Mechanical Engineering National Institute of Technology Rourkela Odisha 769008 India
2 shared publications
Latest Publications
- 29 August 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 237 (3) , 714-723
Evaluation of dry sliding wear behavior of abaca/glass fiber hybrid composite for tribological applications
Abaca is a high-strength natural fiber whose tribological behavior in epoxy polymer composite is unexplored to date. This paper aims to study the mechanical and dry sliding wear behavior of abaca fiber (A) and glass fiber (G) reinforced epoxy laminate composites with various stacking sequences. Symmetrically oriented laminate composites were fabricated in different stacking sequences (AAAA, AGAG, AGGA, and GAAG) using hand lay-up technique. Mechanical characterization is carried out as per ASTM standards. It is found that GAAG hybrid composite possesses maximum tensile strength (101.05 MPa). Meanwhile, AGAG composite shows maximum flexural strength (190.15 MPa) and interlaminar shear strength (5.97 MPa). Abrasive wear behavior of the composites is investigated by performing the test on a pin-on-disc tribo tester as per the ASTM G99 standard under dry sliding conditions. Tribological results indicate that hybridization of abaca and glass fiber into an epoxy matrix enhances the wear properties significantly. Maximum wear resistance is observed with AGGA-layered hybrid composite. The reduction in volumetric wear of AGGA composite is found to be lower than neat epoxy by 86.51%. However, the frictional force of AGGA composite increased by 54.17%. Furthermore, the morphology of fractured and worn-out surfaces is studied using a scanning electron microscope. It is inferred that failure is mainly due to the development of micro-cracks on both fiber and matrix, combined with fiber fragmentation, plowing, and debonding.
- 29 August 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 237 (3) , 714-723
Evaluation of dry sliding wear behavior of abaca/glass fiber hybrid composite for tribological applications
Abaca is a high-strength natural fiber whose tribological behavior in epoxy polymer composite is unexplored to date. This paper aims to study the mechanical and dry sliding wear behavior of abaca fiber (A) and glass fiber (G) reinforced epoxy laminate composites with various stacking sequences. Symmetrically oriented laminate composites were fabricated in different stacking sequences (AAAA, AGAG, AGGA, and GAAG) using hand lay-up technique. Mechanical characterization is carried out as per ASTM standards. It is found that GAAG hybrid composite possesses maximum tensile strength (101.05 MPa). Meanwhile, AGAG composite shows maximum flexural strength (190.15 MPa) and interlaminar shear strength (5.97 MPa). Abrasive wear behavior of the composites is investigated by performing the test on a pin-on-disc tribo tester as per the ASTM G99 standard under dry sliding conditions. Tribological results indicate that hybridization of abaca and glass fiber into an epoxy matrix enhances the wear properties significantly. Maximum wear resistance is observed with AGGA-layered hybrid composite. The reduction in volumetric wear of AGGA composite is found to be lower than neat epoxy by 86.51%. However, the frictional force of AGGA composite increased by 54.17%. Furthermore, the morphology of fractured and worn-out surfaces is studied using a scanning electron microscope. It is inferred that failure is mainly due to the development of micro-cracks on both fiber and matrix, combined with fiber fragmentation, plowing, and debonding.
- 11 May 2022
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 75 (9) , 2355-2365
Dry Sliding Wear Behaviour of Epoxy/Biochar Composites
- 11 May 2022
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 75 (9) , 2355-2365
Dry Sliding Wear Behaviour of Epoxy/Biochar Composites
- 9 October 2021
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 75 (2) , 337-349
Effect of Weathering on Physical and Mechanical Characteristics of Eulaliopsis Binata Fiber/Epoxy Composites
- 9 October 2021
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 75 (2) , 337-349
Effect of Weathering on Physical and Mechanical Characteristics of Eulaliopsis Binata Fiber/Epoxy Composites
- 22 September 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 236 (2) , 334-344
Bio waste (Pistacia vera nut shell) filled polymer composites for tribological applications
The environmental concerns and quest for a sustainable future have encouraged the utilisation of bio-waste in a productive manner. In the present investigation, characterization studies such EDS, XRD and FTIR of pistacia vera (pistachio) nut shell particulates were carried out to have a knowledge of the morphological properties. Further, an attempt was made to utilise the bio-waste i.e. pistacia vera nut shell as a reinforcing phase in epoxy based polymer composites to assess the tribological behaviour of the fabricated composites. The pistachio shell particulate was incorporated with epoxy resin in different weight fractions (0, 10, 20 and 30%) to develop a new class of composite. The effect of filler content, normal load, sliding velocity and sliding distance on the two body abrasive wear behaviour of pistachio shell particulate reinforced epoxy composites was studied. The obtained results showed significant enhancement of abrasion resistance of the fabricated composites as compared to neat epoxy. Further, it was found that the composites with 20 weight percent of filler provide optimum abrasion resistance to the developed composite. The worn out surfaces of the composites were analysed using Scanning Electron Microscope to determine various failure mechanisms leading to deformation of the composite surface.
- 22 September 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 236 (2) , 334-344
Bio waste (Pistacia vera nut shell) filled polymer composites for tribological applications
The environmental concerns and quest for a sustainable future have encouraged the utilisation of bio-waste in a productive manner. In the present investigation, characterization studies such EDS, XRD and FTIR of pistacia vera (pistachio) nut shell particulates were carried out to have a knowledge of the morphological properties. Further, an attempt was made to utilise the bio-waste i.e. pistacia vera nut shell as a reinforcing phase in epoxy based polymer composites to assess the tribological behaviour of the fabricated composites. The pistachio shell particulate was incorporated with epoxy resin in different weight fractions (0, 10, 20 and 30%) to develop a new class of composite. The effect of filler content, normal load, sliding velocity and sliding distance on the two body abrasive wear behaviour of pistachio shell particulate reinforced epoxy composites was studied. The obtained results showed significant enhancement of abrasion resistance of the fabricated composites as compared to neat epoxy. Further, it was found that the composites with 20 weight percent of filler provide optimum abrasion resistance to the developed composite. The worn out surfaces of the composites were analysed using Scanning Electron Microscope to determine various failure mechanisms leading to deformation of the composite surface.
- 24 May 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 236 (2) , 284-291
Erosion wear behaviour of A357/fly ash composites
In this article, a new metal–matrix composite was developed with fly ash (an industrial waste from petroleum industries) as reinforcement and aluminium metal (A357) as a matrix by squeeze casting technique. This study was concentrated on the processing of the composites with different weight percentage ranging from 0 to 10 wt.% in a step of 2.5 each and also reported the erosion wear behaviour. Solid particle erosion of A357/fly ash composites was carried out with four velocities (48, 70, 82 and 109 m/s), at impact angles (30°, 45°, 60° and 90°), with silica as an abrasive particle at ambient temperature. The eroded surfaces were analysed by scanning electron microscopy. The results revealed that the impact velocity and impingement angle both affected the erosion wear behaviour of the composites. The erosion rate rises with an increase in impact velocity, irrespective of the change in impingement angle and weight percentage of the fly ash. The erosion mechanism studied for the composites is microploughing and microcutting.
- 24 May 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 236 (2) , 284-291
Erosion wear behaviour of A357/fly ash composites
In this article, a new metal–matrix composite was developed with fly ash (an industrial waste from petroleum industries) as reinforcement and aluminium metal (A357) as a matrix by squeeze casting technique. This study was concentrated on the processing of the composites with different weight percentage ranging from 0 to 10 wt.% in a step of 2.5 each and also reported the erosion wear behaviour. Solid particle erosion of A357/fly ash composites was carried out with four velocities (48, 70, 82 and 109 m/s), at impact angles (30°, 45°, 60° and 90°), with silica as an abrasive particle at ambient temperature. The eroded surfaces were analysed by scanning electron microscopy. The results revealed that the impact velocity and impingement angle both affected the erosion wear behaviour of the composites. The erosion rate rises with an increase in impact velocity, irrespective of the change in impingement angle and weight percentage of the fly ash. The erosion mechanism studied for the composites is microploughing and microcutting.
- 4 February 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 235 (10) , 2099-2109
Abrasive wear behaviour of orange peel (biowaste) particulate reinforced polymer composites
The development of lightweight materials has drawn more attention in the last decade in the field of household, construction and automobile sectors in place of conventional materials. New environmental policies are forcing researchers to design and develop new lightweight materials that are environmentally friendly. The development of bio-composites in place of synthetic fibre composites is one of the solutions for this. This article deals with an experimental investigation of tribological properties of orange peel particulate (a biowaste) epoxy composites. The hand layup technique is used to fabricate the composite material by varying the filler loading from 0 to 30% with a variation of 10%. The abrasive wear behaviour of the fabricated composite was analysed by using a pin-on-disc set up under dry sliding conditions with varying loads at different sliding velocities. Based on the experiments, it is observed that the wear behaviour of neat epoxy material has enhanced significantly with the addition of the orange peel particulates as filler materials. The characterisation of orange peel particulates was done using energy-dispersive X-ray spectroscopy, X-ray diffraction and Fourier transform infrared spectroscopy. The surface morphology study of the worn surface with respect to wear mechanism indicates plastic deformation and development of cracks at optimum filler concentration (20 wt%). With a higher filler concentration (30 wt%), brittle failure of the composite was noticed.
- 4 February 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 235 (10) , 2099-2109
Abrasive wear behaviour of orange peel (biowaste) particulate reinforced polymer composites
The development of lightweight materials has drawn more attention in the last decade in the field of household, construction and automobile sectors in place of conventional materials. New environmental policies are forcing researchers to design and develop new lightweight materials that are environmentally friendly. The development of bio-composites in place of synthetic fibre composites is one of the solutions for this. This article deals with an experimental investigation of tribological properties of orange peel particulate (a biowaste) epoxy composites. The hand layup technique is used to fabricate the composite material by varying the filler loading from 0 to 30% with a variation of 10%. The abrasive wear behaviour of the fabricated composite was analysed by using a pin-on-disc set up under dry sliding conditions with varying loads at different sliding velocities. Based on the experiments, it is observed that the wear behaviour of neat epoxy material has enhanced significantly with the addition of the orange peel particulates as filler materials. The characterisation of orange peel particulates was done using energy-dispersive X-ray spectroscopy, X-ray diffraction and Fourier transform infrared spectroscopy. The surface morphology study of the worn surface with respect to wear mechanism indicates plastic deformation and development of cracks at optimum filler concentration (20 wt%). With a higher filler concentration (30 wt%), brittle failure of the composite was noticed.
- 26 November 2020
- Published by Springer Nature
- p. 607-615
Wear Behavior of Orange Peel Reinforced Epoxy Composite
- 26 November 2020
- Published by Springer Nature
- p. 607-615
Wear Behavior of Orange Peel Reinforced Epoxy Composite
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 26, 1936-1940
Study of mechanical behaviour of raw and chemical treated bio-filler composites and its effect on moisture absorption
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 26, 1936-1940
Study of mechanical behaviour of raw and chemical treated bio-filler composites and its effect on moisture absorption