Hyo-Chan Kwon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Hyo-Chan Kwon has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Doo-Hyun Cho
Department of Mechanical Engineering, Graduate school, Korea University, Seoul, Republic of Korea
2 shared publications - Kwon-Hee Kim
Department of Mechanical Engineering, Korea University, 145, Anam-Ro, Seongbuk-gu, Seoul 02841, Korea
2 shared publications - Eun-Joo Park
Department of Electrical Engineering, Gyeonggi University of Science and Technology, Siheung 15073, Republic of Korea
1 shared publication - Jinkwang Lee
Department of Mechanical Convergence Engineering, Gyeongsang National University, 54, Charyong-ro 48beon-gil, Uichang-gu, Changwon-si 51391, Republic of Korea
1 shared publication
Latest Publications
- Open Access
- 3 May 2026
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 14 (9) , 858
Start–Stop Cycle-Induced Failure-Mode Transition in SOFC-Powered Northern Sea Route Shipping: A Hierarchical Bayesian Competing-Risk Analysis
Solid oxide fuel cells (SOFCs) are a promising near-zero-emission propulsion source for Northern Sea Route (NSR) vessels, but their yttria-stabilized zirconia (YSZ) electrolyte and Ni-cermet anode are susceptible to thermomechanical degradation under repetitive start–stop thermal cycling. We develop a hierarchical Bayesian competing-risk framework built on a dual degradation model that decomposes area-specific resistance (ASR) growth into cycle-induced fatigue and time-dependent electrochemical aging and apply it across six NSR duty-cycle scenarios spanning f = 1–27 cycles/month. Posterior inference via the No-U-Turn Sampler (NUTS) yields 17 estimated parameters meeting standard convergence criteria (R^ ≤ 1.01, ESSbulk ≥ 479, zero divergent transitions). The analysis identifies a failure-mode transition at f ≈ 3–6 cycles/month: high-frequency routes are crack-dominated (S1a: 10/15 cells fail by crack within the 600-cycle window with 5/15 right-censored), whereas low-frequency routes are ASR-dominated (S3b: 100% ASR). Global sensitivity analysis indicates the time-dependent rate coefficient ktime as the primary remaining-useful-life driver (ST = 0.37–0.46). Cycle-based maintenance thresholds span 160 cycles (S3b) to ≥600 cycles (S2b), bracketed by S1a (270 cycles, 10.0 months, crack-dominant) and S3a (480 cycles, 160 months, transition regime); qualitative consistency with published experimental data supports physical plausibility.
- 3 May 2026
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 14 (9) , 858
Open AccessStart–Stop Cycle-Induced Failure-Mode Transition in SOFC-Powered Northern Sea Route Shipping: A Hierarchical Bayesian Competing-Risk Analysis
Solid oxide fuel cells (SOFCs) are a promising near-zero-emission propulsion source for Northern Sea Route (NSR) vessels, but their yttria-stabilized zirconia (YSZ) electrolyte and Ni-cermet anode are susceptible to thermomechanical degradation under repetitive start–stop thermal cycling. We develop a hierarchical Bayesian competing-risk framework built on a dual degradation model that decomposes area-specific resistance (ASR) growth into cycle-induced fatigue and time-dependent electrochemical aging and apply it across six NSR duty-cycle scenarios spanning f = 1–27 cycles/month. Posterior inference via the No-U-Turn Sampler (NUTS) yields 17 estimated parameters meeting standard convergence criteria (R^ ≤ 1.01, ESSbulk ≥ 479, zero divergent transitions). The analysis identifies a failure-mode transition at f ≈ 3–6 cycles/month: high-frequency routes are crack-dominated (S1a: 10/15 cells fail by crack within the 600-cycle window with 5/15 right-censored), whereas low-frequency routes are ASR-dominated (S3b: 100% ASR). Global sensitivity analysis indicates the time-dependent rate coefficient ktime as the primary remaining-useful-life driver (ST = 0.37–0.46). Cycle-based maintenance thresholds span 160 cycles (S3b) to ≥600 cycles (S2b), bracketed by S1a (270 cycles, 10.0 months, crack-dominant) and S3a (480 cycles, 160 months, transition regime); qualitative consistency with published experimental data supports physical plausibility.
- Open Access
- 10 January 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (2) , 657
Improvement of Position Repeatability of a Linear Stage with Yaw Minimization
Recently, due to the miniaturization of electronic products, printed circuit boards (PCBs) have also become smaller. This trend has led to the need for high-precision electrical test equipment to check PCBs for disconnections and short circuits. The purpose of this study is to improve the position repeatability of the platform unit up to ±2.5 μm in linear stage type test equipment. For this purpose, the causes of the position errors of the platform unit are analyzed. The platform unit holding the PCB is driven by a single-axis linear ball screw drive system offset from its geometric center due to design constraints. The yaw rotation of the platform is found to have a dominant effect on position repeatability. To address this problem, adding balancing weights to the platform unit and adjusting the stiffness of the LM Guides are proposed. These methods reduce the yaw rotation by moving the centers of mass and stiffness closer to the linear ball screw actuator. In the verification tests, the position repeatability was decreased to less than ±1.0 μm.
- 10 January 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (2) , 657
Open AccessImprovement of Position Repeatability of a Linear Stage with Yaw Minimization
Recently, due to the miniaturization of electronic products, printed circuit boards (PCBs) have also become smaller. This trend has led to the need for high-precision electrical test equipment to check PCBs for disconnections and short circuits. The purpose of this study is to improve the position repeatability of the platform unit up to ±2.5 μm in linear stage type test equipment. For this purpose, the causes of the position errors of the platform unit are analyzed. The platform unit holding the PCB is driven by a single-axis linear ball screw drive system offset from its geometric center due to design constraints. The yaw rotation of the platform is found to have a dominant effect on position repeatability. To address this problem, adding balancing weights to the platform unit and adjusting the stiffness of the LM Guides are proposed. These methods reduce the yaw rotation by moving the centers of mass and stiffness closer to the linear ball screw actuator. In the verification tests, the position repeatability was decreased to less than ±1.0 μm.
- 12 February 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 22 (5) , 791-798
Underactuated Three-Finger Robot Hand with Human-Like Flexion
- 12 February 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 22 (5) , 791-798
Underactuated Three-Finger Robot Hand with Human-Like Flexion