Xiaodong Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Xiaodong Wang has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Xuesong Mei
State Key Laboratory for Manufacturing Systems Engineering, Xi’an Jiaotong University, Xi’an, China
7 shared publications - Bin Liu
State Key Laboratory for Manufacturing Systems Engineering, Xi’an Jiaotong University, Xi’an, China
6 shared publications - Xintian Wang
Xi′an Modern Chemistry Research Institute, Xi′an 710065, China
5 shared publications - Renhan Lian
School of Mechanical Engineering, Xian Jiaotong University, Xian, China
2 shared publications - Zheng Sun
School of Mechanical Engineering, Xi’an Jiaotong University, Xi’an 710049, China
2 shared publications - Bin Liu
TCL China Star Optoelectronics Technology Co., Ltd, Shenzhen 518132, People’s Republic of China
1 shared publication
Latest Publications
- 28 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Informatics
- Vol. 20 (3) , 3266-3274
Disturbance Observer-Based Adaptive Neural Control of the Permanent Magnet Linear Motor System With Unknown Backlash-Like Hysteresis
In the large-area multidevice linkage-based laser processing, using the traditional control method cannot guarantee the processing accuracy of a permanent magnet linear motor (PMLM) system for a high-speed subject, due to unknown model uncertainties, backlash-like hysteresis, states constraints, and external disturbance. To address this shortcoming, this article develops a disturbance observe-based adaptive neural control for the PMLM system. First, aiming at the problem of unknown and uncertain system parameters, this study uses a radial basis neural network to estimate unknown functions of the system. Then, an adaptive variable is introduced to compensate for the effect of unknown backlash-like hysteresis, and the barrier Lyapunov function is used to restrict the motor from operating in a specified area. In addition, a nonlinear disturbance observer is constructed to adapt to the actual processing to reduce the influence of the external disturbance and the system load change. The proposed control scheme is verified experimentally, and the results indicate that when the proposed method is used, the PMLM system is consistently bounded by using the Lyapunov theorem. Finally, the simulation and experimental results verify the effectiveness of the proposed control strategy. The proposed method could be applied to laser-processing equipment.
- 28 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Informatics
- Vol. 20 (3) , 3266-3274
Disturbance Observer-Based Adaptive Neural Control of the Permanent Magnet Linear Motor System With Unknown Backlash-Like Hysteresis
In the large-area multidevice linkage-based laser processing, using the traditional control method cannot guarantee the processing accuracy of a permanent magnet linear motor (PMLM) system for a high-speed subject, due to unknown model uncertainties, backlash-like hysteresis, states constraints, and external disturbance. To address this shortcoming, this article develops a disturbance observe-based adaptive neural control for the PMLM system. First, aiming at the problem of unknown and uncertain system parameters, this study uses a radial basis neural network to estimate unknown functions of the system. Then, an adaptive variable is introduced to compensate for the effect of unknown backlash-like hysteresis, and the barrier Lyapunov function is used to restrict the motor from operating in a specified area. In addition, a nonlinear disturbance observer is constructed to adapt to the actual processing to reduce the influence of the external disturbance and the system load change. The proposed control scheme is verified experimentally, and the results indicate that when the proposed method is used, the PMLM system is consistently bounded by using the Lyapunov theorem. Finally, the simulation and experimental results verify the effectiveness of the proposed control strategy. The proposed method could be applied to laser-processing equipment.
- 12 November 2022
- Published by Springer Nature in Journal of Intelligent Manufacturing
- Vol. 35 (1) , 331-341
A quality improvement method for complex component fine manufacturing based on terminal laser beam deflection compensation
- 12 November 2022
- Published by Springer Nature in Journal of Intelligent Manufacturing
- Vol. 35 (1) , 331-341
A quality improvement method for complex component fine manufacturing based on terminal laser beam deflection compensation
- 29 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (10) , 10634-10643
A Novel Method for Measuring, Collimating, and Maintaining the Spatial Pose of Terminal Beam in Laser Processing System Based on 3D and 2D Hybrid Vision
The terminal beam collimation problem of laser processing systems has traditionally been a headache. The deflection of the terminal beam seriously affects the processing accuracy and success. In this article, A novel method for measuring, collimating, and maintaining the spatial pose of the terminal beam in a five-axis laser processing system based on 3-D and 2-D hybrid vision is proposed. The beam pose in the working space of the laser processing system is measured by using a 3D scanner and an alignment sensor. The functional relationship between the galvanometer coordinates and the deflection angles of the terminal beam is established. The coordinates corresponding to the minimum deflection angle are solved to collimate the beam. Moreover, a camera is used to monitor the laser spot and re-collimate the deflected beam. The experimental results show that the method proposed in this article can effectively measure the deflection angle of the terminal beam, collimate the terminal beam and monitor the spot position of the terminal beam. The method can effectively improve the processing accuracy when applied to the laser processing system and has excellent potential application value.
- 29 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 69 (10) , 10634-10643
A Novel Method for Measuring, Collimating, and Maintaining the Spatial Pose of Terminal Beam in Laser Processing System Based on 3D and 2D Hybrid Vision
The terminal beam collimation problem of laser processing systems has traditionally been a headache. The deflection of the terminal beam seriously affects the processing accuracy and success. In this article, A novel method for measuring, collimating, and maintaining the spatial pose of the terminal beam in a five-axis laser processing system based on 3-D and 2-D hybrid vision is proposed. The beam pose in the working space of the laser processing system is measured by using a 3D scanner and an alignment sensor. The functional relationship between the galvanometer coordinates and the deflection angles of the terminal beam is established. The coordinates corresponding to the minimum deflection angle are solved to collimate the beam. Moreover, a camera is used to monitor the laser spot and re-collimate the deflected beam. The experimental results show that the method proposed in this article can effectively measure the deflection angle of the terminal beam, collimate the terminal beam and monitor the spot position of the terminal beam. The method can effectively improve the processing accuracy when applied to the laser processing system and has excellent potential application value.
- 1 March 2022
- Published by Elsevier in Ceramics International
- Vol. 48 (6) , 7593-7604
Picosecond laser trimming of ceramic cores with porous multi-scale particle microstructure
- 1 March 2022
- Published by Elsevier in Ceramics International
- Vol. 48 (6) , 7593-7604
Picosecond laser trimming of ceramic cores with porous multi-scale particle microstructure
- 7 October 2021
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 149, 106834
An adaptive laser focus auto-positioning method for non-datum complex components based on 3D vision
- 7 October 2021
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 149, 106834
An adaptive laser focus auto-positioning method for non-datum complex components based on 3D vision
- 16 February 2021
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 28 (11-12) , 1433-1440
Genetic algorithm for dynamic parameters estimation of the machine tool worktable using the residual vibration signal
In this article, the residual vibration signal of the worktable of the machine tool is used to identify its dynamic parameters. By analyzing the time-domain characteristics of the residual vibration signal, it is found that the signal has the similar attenuation characteristics to the impulse response of the second-order underdamped system, so a new method for identifying the dynamic parameters of the worktable is proposed. In this method, the impulse response model of the second-order underdamped system is used to describe the residual vibration signal, so the parameter identification problem based on the time-domain signal is transformed into the optimization problem of the model parameters. Then, the dynamic parameters can be determined by using the genetic algorithm. The results of the genetic algorithm are compared with the results of the autoregressive moving average method, which is a commonly used parameter identification method based on the time-domain signal. It was found that the results of the model-based method proposed in this article are more accurate than the autoregressive moving average method.
- 16 February 2021
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 28 (11-12) , 1433-1440
Genetic algorithm for dynamic parameters estimation of the machine tool worktable using the residual vibration signal
In this article, the residual vibration signal of the worktable of the machine tool is used to identify its dynamic parameters. By analyzing the time-domain characteristics of the residual vibration signal, it is found that the signal has the similar attenuation characteristics to the impulse response of the second-order underdamped system, so a new method for identifying the dynamic parameters of the worktable is proposed. In this method, the impulse response model of the second-order underdamped system is used to describe the residual vibration signal, so the parameter identification problem based on the time-domain signal is transformed into the optimization problem of the model parameters. Then, the dynamic parameters can be determined by using the genetic algorithm. The results of the genetic algorithm are compared with the results of the autoregressive moving average method, which is a commonly used parameter identification method based on the time-domain signal. It was found that the results of the model-based method proposed in this article are more accurate than the autoregressive moving average method.
- Open Access
- 29 June 2020
- Published by Wiley in Shock and Vibration
- Vol. 2020, 1-15
A Novel Method to Reduce the Laser Drilling Time for Hole Cluster considering the Influence of Residual Vibration of the Sample Stage
In large areas of laser drilling, the residual vibration occurs when the sample stage moves in PTP (Point to Point) movement. It affects the surface quality and processing efficiency of the holes. The common solution for this problem is to set the laser irradiation delay time by the controller to wait for the residual vibration attenuation, but the whole drilling circle will increase. In this paper, a new method is introduced to reduce the laser drilling circle. By setting the allowable threshold of the residual vibration for the subsequent process, the sum of the time in deceleration segment of the trapezoidal moving profile, and the time when the residual vibration attenuates below the amplitude threshold (ST) can be minimized as the optimization goal. The results show that for a given operating speed, there is always an optimum acceleration value for the deceleration segment of the trapezoidal moving profile, which minimizes the ST value. Further, the delay time for laser irradiation can also be estimated according to the optimal acceleration during laser drilling.
- 29 June 2020
- Published by Wiley in Shock and Vibration
- Vol. 2020, 1-15
Open AccessA Novel Method to Reduce the Laser Drilling Time for Hole Cluster considering the Influence of Residual Vibration of the Sample Stage
In large areas of laser drilling, the residual vibration occurs when the sample stage moves in PTP (Point to Point) movement. It affects the surface quality and processing efficiency of the holes. The common solution for this problem is to set the laser irradiation delay time by the controller to wait for the residual vibration attenuation, but the whole drilling circle will increase. In this paper, a new method is introduced to reduce the laser drilling circle. By setting the allowable threshold of the residual vibration for the subsequent process, the sum of the time in deceleration segment of the trapezoidal moving profile, and the time when the residual vibration attenuates below the amplitude threshold (ST) can be minimized as the optimization goal. The results show that for a given operating speed, there is always an optimum acceleration value for the deceleration segment of the trapezoidal moving profile, which minimizes the ST value. Further, the delay time for laser irradiation can also be estimated according to the optimal acceleration during laser drilling.