Larissa Jangidze
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Larissa Jangidze has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Amiran Bibilashvili
Institute of Micro and Nano Electronics, Chavchavadze Ave. 13, Tbilisi 0179, Georgia
3 shared publications - Avto Tavkhelidze
Center of Nanotechnology for Renewable Energy, Ilia State University, Cholokashvili Ave. 3/5, Tbilisi 0162, Georgia
3 shared publications - Nima E. Gorji
Mechatronic Engineering, Technological University Dublin, Dublin 15, Ireland
3 shared publications - Sergo Sikharulidze
Center of Nanotechnology for Renewable Energy, Ilia State University, Cholokashvili Ave. 3/5, Tbilisi 0162, Georgia
2 shared publications - Zaza Taliashvili
Institute of micro and nano electronics, Tbilisi, GEORGIA
2 shared publications - Afshin Bakhtiari
Georgian Technical University Kostava Str. 77 0160 Tbilisi Georgia
1 shared publication
Latest Publications
- Open Access
- 1 November 2026
- Published by Polish Mineral Engineering Society in Inżynieria Mineralna
- Vol. 1 (2)
Ultra-Wide Band Gap Material Gallium Oxide, Technology, Properties, Characterization
Gallium oxide (Ga₂O₃) is a ultra wide-bandgap semiconductor (4.7 ~ 5.3 eV) that has garnered significant attention for its exceptional structural, optical, and electrical properties, which make it suitable for high-power electronics, UV photodetectors, and catalysis. Structurally, Ga₂O₃ exhibits polymorphism, with α-, β-, γ-, δ-, ε-, and κ-phases, among which β-Ga₂O₃ is the most thermodynamically stable under ambient conditions. Synthesis methods, including hydrothermal growth, sol-gel processes, RF/DC sputtering, atomic layer deposition (ALD) and molecular beam epitaxy (MBE) enable precise control over phase formation, crystallinity, and defect density. In the present work is demonstrated the reactive magnetron sputtering (DC) technology for formation β-Ga₂O₃. As substrate is used 2-inch, (0006) orientation and 400μ thickness sapphire wafer. Experiments are made in different condition (power, oxygen partial pressure, time, temperature etc.) for analyzing the best technological rout of growing Ga₂O₃ with good structural, optical and electrical properties. X-ray structural analysis (XRD) was measured and a small peak was identified at the diffraction angle 2θ=20.5°. In terms of optical properties, transmission spectra were measured. The calculated optical band gap was ~ 5 eV. Electrically, Ga₂O₃ behaves predominantly as an n-type semiconductor due to oxygen vacancies. Undoped β-Ga₂O₃ exhibits high resistivity (~10⁶ Ω·cm). Electrical measurements also were performed on an HP 4279A C-V Meter to obtain a C-V profile, and the thicknesses of the deposited films were calculated from the graphs and compared with the values measured on the profilometer.
- 1 November 2026
- Published by Polish Mineral Engineering Society in Inżynieria Mineralna
- Vol. 1 (2)
Open AccessUltra-Wide Band Gap Material Gallium Oxide, Technology, Properties, Characterization
Gallium oxide (Ga₂O₃) is a ultra wide-bandgap semiconductor (4.7 ~ 5.3 eV) that has garnered significant attention for its exceptional structural, optical, and electrical properties, which make it suitable for high-power electronics, UV photodetectors, and catalysis. Structurally, Ga₂O₃ exhibits polymorphism, with α-, β-, γ-, δ-, ε-, and κ-phases, among which β-Ga₂O₃ is the most thermodynamically stable under ambient conditions. Synthesis methods, including hydrothermal growth, sol-gel processes, RF/DC sputtering, atomic layer deposition (ALD) and molecular beam epitaxy (MBE) enable precise control over phase formation, crystallinity, and defect density. In the present work is demonstrated the reactive magnetron sputtering (DC) technology for formation β-Ga₂O₃. As substrate is used 2-inch, (0006) orientation and 400μ thickness sapphire wafer. Experiments are made in different condition (power, oxygen partial pressure, time, temperature etc.) for analyzing the best technological rout of growing Ga₂O₃ with good structural, optical and electrical properties. X-ray structural analysis (XRD) was measured and a small peak was identified at the diffraction angle 2θ=20.5°. In terms of optical properties, transmission spectra were measured. The calculated optical band gap was ~ 5 eV. Electrically, Ga₂O₃ behaves predominantly as an n-type semiconductor due to oxygen vacancies. Undoped β-Ga₂O₃ exhibits high resistivity (~10⁶ Ω·cm). Electrical measurements also were performed on an HP 4279A C-V Meter to obtain a C-V profile, and the thicknesses of the deposited films were calculated from the graphs and compared with the values measured on the profilometer.
- Open Access
- 1 November 2026
- Published by Polish Mineral Engineering Society in Inżynieria Mineralna
- Vol. 1 (2)
Laser-Plasma Technology for Creating Silicon-Graphene Solar Cells
In response to the growing concerns of global warming and the urgent need for sustainable energy solutions, the exploration of alternative energy sources has become increasingly important. Among these, solar energy stands out as a clean, abundant, and renewable option. The efficiency of solar cells depends significantly on the base semiconductor material, with silicon currently dominating global production. However, modern research focuses on enhancing solar cell performance through innovative approaches, such as the deposition of graphene layers using advanced laser-plasma technology. Laser-plasma technology integrates laser ablation and plasma deposition techniques to fabricate high-efficiency thin-film solar cells, including those based on silicon-graphene nanosystems. This approach enables precise structuring, local doping, and film growth at the nanoscale, which enhances optical absorption, electrical conductivity, and carrier collection efficiency. By optimizing the deposition process and exploring various technological conditions, graphene-enhanced solar cells can achieve improved electrical conductivity, better light absorption, and reduced energy losses, paving the way for highly efficient and environmentally friendly solar energy solutions. The presented work discusses the deposition of graphene on a solar cell using laser-plasma deposition technology and the analysis of the results obtained. Experiments were conducted under various technological conditions in order to investigate the optimal conditions for obtaining high-efficiency solar cells. In the experiments used 2-inch diameter, (100) crystallographic orientation and 400 μm thick p-type silicon wafers. Different phosphorus diffusion depths were considered to achieve n-type conductivity. In one case, silicon nitride and graphene were used as the antireflective layer, and in the other case, only graphene was used. The volt-ampere characteristic was measured and the margin action coefficient of the solar cell was estimated in each experiment. The parameters of the solar cell obtained with and without graphene were compared.
- 1 November 2026
- Published by Polish Mineral Engineering Society in Inżynieria Mineralna
- Vol. 1 (2)
Open AccessLaser-Plasma Technology for Creating Silicon-Graphene Solar Cells
In response to the growing concerns of global warming and the urgent need for sustainable energy solutions, the exploration of alternative energy sources has become increasingly important. Among these, solar energy stands out as a clean, abundant, and renewable option. The efficiency of solar cells depends significantly on the base semiconductor material, with silicon currently dominating global production. However, modern research focuses on enhancing solar cell performance through innovative approaches, such as the deposition of graphene layers using advanced laser-plasma technology. Laser-plasma technology integrates laser ablation and plasma deposition techniques to fabricate high-efficiency thin-film solar cells, including those based on silicon-graphene nanosystems. This approach enables precise structuring, local doping, and film growth at the nanoscale, which enhances optical absorption, electrical conductivity, and carrier collection efficiency. By optimizing the deposition process and exploring various technological conditions, graphene-enhanced solar cells can achieve improved electrical conductivity, better light absorption, and reduced energy losses, paving the way for highly efficient and environmentally friendly solar energy solutions. The presented work discusses the deposition of graphene on a solar cell using laser-plasma deposition technology and the analysis of the results obtained. Experiments were conducted under various technological conditions in order to investigate the optimal conditions for obtaining high-efficiency solar cells. In the experiments used 2-inch diameter, (100) crystallographic orientation and 400 μm thick p-type silicon wafers. Different phosphorus diffusion depths were considered to achieve n-type conductivity. In one case, silicon nitride and graphene were used as the antireflective layer, and in the other case, only graphene was used. The volt-ampere characteristic was measured and the margin action coefficient of the solar cell was estimated in each experiment. The parameters of the solar cell obtained with and without graphene were compared.
- Open Access
- 20 September 2023
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 55 (11) , 1-9
Optical properties of periodically and aperiodically nanostructured p-n junctions
Recently, semiconductor nanograting layers have been introduced and their optical properties have been studied. Spectroscopic ellipsometry has shown that nanograting significantly modifies the dielectric function of c-Si layers. Photoluminescence spectroscopy reveals the emergence of an emission band with a remarkable peak structure. It has been observed that nanograting also alters the electronic and magnetic properties. In this study, we investigate the quantum efficiency and spectral response of Si p-n junctions fabricated using subwavelength grating layers and aperiodically nanostructured layers. Our findings indicate that the quantum efficiency and spectral response are enhanced in the case of nanograting p-n junctions compared to plain reference junctions. Aperiodically nanostructured junctions exhibit similar results to nanograting junctions. However, aperiodic nanostructuring is a more straightforward fabrication method and, consequently, more appealing for the solar cell industry.
- 20 September 2023
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 55 (11) , 1-9
Open AccessOptical properties of periodically and aperiodically nanostructured p-n junctions
Recently, semiconductor nanograting layers have been introduced and their optical properties have been studied. Spectroscopic ellipsometry has shown that nanograting significantly modifies the dielectric function of c-Si layers. Photoluminescence spectroscopy reveals the emergence of an emission band with a remarkable peak structure. It has been observed that nanograting also alters the electronic and magnetic properties. In this study, we investigate the quantum efficiency and spectral response of Si p-n junctions fabricated using subwavelength grating layers and aperiodically nanostructured layers. Our findings indicate that the quantum efficiency and spectral response are enhanced in the case of nanograting p-n junctions compared to plain reference junctions. Aperiodically nanostructured junctions exhibit similar results to nanograting junctions. However, aperiodic nanostructuring is a more straightforward fabrication method and, consequently, more appealing for the solar cell industry.
- Open Access
G-Doping-Based Metal-Semiconductor Junction
Geometry-induced doping (G-doping) has been realized in semiconductors nanograting layers. G-doping-based p-p(v) junction has been fabricated and demonstrated with extremely low forward voltage and reduced reverse current. The formation mechanism of p-p(v) junction has been proposed. To obtain G-doping, the surfaces of p-type and p+-type silicon substrates were patterned with nanograting indents of depth d = 30 nm. The Ti/Ag contacts were deposited on top of G-doped layers to form metal-semiconductor junctions. The two-probe method has been used to record the I–V characteristics and the four-probe method has been deployed to exclude the contribution of metal-semiconductor interface. The collected data show a considerably lower reverse current in p-type substrates with nanograting pattern. In the case of p+-type substrate, nanograting reduced the reverse current dramatically (by 1–2 orders of magnitude). However, the forward currents are not affected in both substrates. We explained these unusual I–V characteristics with G-doping theory and p-p(v) junction formation mechanism. The decrease of reverse current is explained by the drop of carrier generation rate which resulted from reduced density of quantum states within the G-doped region. Analysis of energy-band diagrams suggested that the magnitude of reverse current reduction depends on the relationship between G-doping depth and depletion width.
Open AccessG-Doping-Based Metal-Semiconductor Junction
Geometry-induced doping (G-doping) has been realized in semiconductors nanograting layers. G-doping-based p-p(v) junction has been fabricated and demonstrated with extremely low forward voltage and reduced reverse current. The formation mechanism of p-p(v) junction has been proposed. To obtain G-doping, the surfaces of p-type and p+-type silicon substrates were patterned with nanograting indents of depth d = 30 nm. The Ti/Ag contacts were deposited on top of G-doped layers to form metal-semiconductor junctions. The two-probe method has been used to record the I–V characteristics and the four-probe method has been deployed to exclude the contribution of metal-semiconductor interface. The collected data show a considerably lower reverse current in p-type substrates with nanograting pattern. In the case of p+-type substrate, nanograting reduced the reverse current dramatically (by 1–2 orders of magnitude). However, the forward currents are not affected in both substrates. We explained these unusual I–V characteristics with G-doping theory and p-p(v) junction formation mechanism. The decrease of reverse current is explained by the drop of carrier generation rate which resulted from reduced density of quantum states within the G-doped region. Analysis of energy-band diagrams suggested that the magnitude of reverse current reduction depends on the relationship between G-doping depth and depletion width.
- Open Access
- 17 February 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (2) , 505
Fermi-Level Tuning of G-Doped Layers
Recently, geometry-induced quantum effects were observed in periodic nanostructures. Nanograting (NG) geometry significantly affects the electronic, magnetic, and optical properties of semiconductor layers. Silicon NG layers exhibit geometry-induced doping. In this study, G-doped junctions were fabricated and characterized and the Fermi-level tuning of the G-doped layers by changing the NG depth was investigated. Samples with various indent depths were fabricated using laser interference lithography and a consecutive series of reactive ion etching. Four adjacent areas with NG depths of 10, 20, 30, and 40 nm were prepared on the same chip. A Kelvin probe was used to map the work function and determine the Fermi level of the samples. The G-doping-induced Fermi-level increase was recorded for eight sample sets cut separately from p-, n-, p+-, and n+-type silicon substrates. The maximum increase in the Fermi level was observed at a10 nm depth, and this decreased with increasing indent depth in the p- and n-type substrates. Particularly, this reduction was more pronounced in the p-type substrates. However, the Fermi-level increase in the n+- and p+-type substrates was negligible. The obtained results are explained using the G-doping theory and G-doped layer formation mechanism introduced in previous works.
- 17 February 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (2) , 505
Open AccessFermi-Level Tuning of G-Doped Layers
Recently, geometry-induced quantum effects were observed in periodic nanostructures. Nanograting (NG) geometry significantly affects the electronic, magnetic, and optical properties of semiconductor layers. Silicon NG layers exhibit geometry-induced doping. In this study, G-doped junctions were fabricated and characterized and the Fermi-level tuning of the G-doped layers by changing the NG depth was investigated. Samples with various indent depths were fabricated using laser interference lithography and a consecutive series of reactive ion etching. Four adjacent areas with NG depths of 10, 20, 30, and 40 nm were prepared on the same chip. A Kelvin probe was used to map the work function and determine the Fermi level of the samples. The G-doping-induced Fermi-level increase was recorded for eight sample sets cut separately from p-, n-, p+-, and n+-type silicon substrates. The maximum increase in the Fermi level was observed at a10 nm depth, and this decreased with increasing indent depth in the p- and n-type substrates. Particularly, this reduction was more pronounced in the p-type substrates. However, the Fermi-level increase in the n+- and p+-type substrates was negligible. The obtained results are explained using the G-doping theory and G-doped layer formation mechanism introduced in previous works.