NTNikolay Valentinovich Turubanov

Nikolay Valentinovich Turubanov

*This is an algorithmically generated author record based on publicly available information.

Nikolay Valentinovich Turubanov has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    DETERMINING RATIONAL MIXER PARAMETERS BASED ON EXPERIMENTAL RESEARCH RESULTS

    by Nikolay Valentinovich Turubanov, Nikolay Vasilevich Vedenskiy, Fedor Aleksandrovich Kipriyanov

    Feed quality determines the efficiency of animal husbandry. Production of complete mixed feeds under specific farm conditions is promising, but requires the use of highly efficient mixers. The object of this study is a horizontal ribbon mixer with a combined working element with a volume of 0.3 m3, the design of which is protected by a patent of the Russian Federation. Mixing dry loose components of feed mixtures was studied using a multifactorial experiment using the Box-Behnken design. Coarsely ground grain was used as the main component, and peas at a weight concentration of 12.5% were used as the control component. The quality of the finished product was assessed by collecting samples from the material flow using a special sampler in accordance with state standards. The influence of three process factors was experimentally assessed: mixer auger rotation speed from 20 to 30 rpm, mixing chamber filling from 50 to 75%, and material mixing time from 4 to 12 minutes. The obtained data were processed using Statgraphics program. Adequate mathematical models of the process were obtained based on the criteria of mixture homogeneity, specific energy consumption and throughput with a high determination coefficient. Based on a comprehensive analysis of two-dimensional sections of the response surfaces, rational design and process parameters of the mixer were established: chamber filling with material - 67.7%, process cycle time - 12 minutes, working element rotation speed - 20 rpm. These parameters ensure the best balance between process quality and energy efficiency: the finished mixture uniformity coefficient is 94.0% with a specific energy consumption of 2.4 kWh/t and a throughput of 0.57 t/h. The mixer’s maximum throughput reaches 1.2 t/h, while mixing quality decreases to 89.0%.

  • Open Access

    The Effect of Air Pressure on the Technological Process of Grinding in the Grain Hammer Mill

    by Petr A. Savinykh, Nikolay V. Turubanov, Aleksey V. Aleshkin, Vladimir A. Suhlyaev

    Introduction. The main problem of the grain hammer mill is over-grinding of grain caused by untimely removal of the final product from the grinding chamber. A way to effect the air flow arrangement in the grain hammer mill is to change the air pressure around the grinding chamber. Therefore, the study of the effect of air pressure around the grain hammer mill on the quality and energy indicators of its operation is an urgent task today.Aim of the Study. The study is aimed at determining the effect of air pressure around the grinding chamber on the air flow motion pattern in the grain hammer mill and its energy indicators.Materials and Methods. For a theoretical study of the air flow circulation in the grinding chamber, there was constructed a geometric model of the rotor placed in the grinding chamber. The Reynolds averaged equations of a continuous medium motion was the basis for the mathematical model of air motion. The calculation results were used to construct the velocity fields for the air flow. To conduct experimental studies, there was designed a pressure chamber that allows changing the air pressure in the grain hammer mill.Results. Based on the results of theoretical studies, it has been determined that the pressure decrease in the grinding chamber by 10 times reduces the power consumption by 112 watts. Experimental studies have shown that when the pressure in the grinding chamber decreases, the power consumed by the engine for all types of rotors decreases too. Also, an increase in air pressure in the grinding chamber leads to a change in the amount of grinded grain remains on the sieve to 0 mm: for the blade and hammer rotors, the amount of remains decreases, and for the hammer-blade rotor it increases.Discussion and Conclusions. The results of theoretical and experimental studies have shown that decreasing the air pressure around the grinding chamber can decrease the energy costs for the technological process and air flow motion inside the grinding chamber, and reduce the over-grinding of grain. The study results make it possible to design the grinding chambers for grain hammer mills taking into account the air flow motion.


  • Open Access

    Determination of optimal technological parameters of a horizontal mixer of loose compound feeds

    by P. A. Savinyh, N. V. Turubanov, A. Ju. Isupov

    The quality of the compound feeds for animals and poultry directly depends not only on the components included in it but also on the type of mixer used. Horizontal mixers as compared to the vertical ones allow for a shorter period of time to obtain high-quality mixtures due to the intensification of the process of material movement by belt working bodies. The aim of the research is to determine optimal technological parameters of a horizontal mixer with a 0.3 m3 mixing chamber with a belt working body. The mixer is designed to produce mixed compound feeds of high uniformity in production lines, workshops or can be used as an independent machine for mixing loose components. The research was carried through multifactorial experiment. As the result, mathematical models of the mixer working process were obtained, two-dimensional cross sections of the response surfaces were built. The obtained mathematical models make it possible at the design stage to identify the dependence of qualitative and energy indicators on factors at the considered levels of variation. According to the results of the multifactorial experiment, it has been established that the best mixing quality of 94.8 % is achieved when the mixing chamber is loaded by 58 % at a speed of rotation of the mixer shaft of 30 min-1, mixing time of 6 minutes with simultaneous supply of the control and the main components. At the same time, the throughput is 0.78 t/h, and the specific energy consumption is 2.04 kWh/t.


  • Open Access

    Determination of optimal design and technological parameters of a hammer crusher with sieves in end surfaces

    by Petr A. Savinyh, Н. В. Турубанов, А. М. Мошонкин, Timirâzevskaâ Selʹskohozâjstvennaâ Akademiâ

    When preparing compound feeds, the main machines used for grain crushing are hammer crushers. To obtain a better-quality finished product with lower energy costs, it is necessary to determine the optimal design and technological parameters of a hammer crusher. To this end, the laboratory of livestock production mechanization has designed a hammer crusher with sieves in the end surfaces. The hammer crusher has adjustable cross-sections of the sieve holes, so there is no need to replace the sieves. Experimental studies have been carried out at the production facilities of the North-East Federal Agency of Scientific Institutions to determine the impact of changes in structural and technological parameters of the crusher on its main performance indicators. According to the results of experimental studies, mathematical models of the working process of the hammer crusher have been obtained. As a result, the optimal design and technological parameters of the hammer crusher have been determined: the area of the sieve openings 58.6 мм2 ; the height of the material separation ring 40 mm and the size of the air filter area 6 m2 , while the throughput capacity of the crusher is 1.23 t/h, specific energy consumption is 3.44 kWh/(t×units of fineness degree), the average size of crushed particles is 1.45 mm, the share of whole grains in the finished product is 0.17%.


  • Open Access

    The influence of changes in the technological parameters of the feed mixer on its performance

    by P. A. Savinykh, N. V. Turubanov

    To conduct effective animal husbandry and poultry farming, it is necessary to use compound feeds. To prepare them mainly vertical and horizontal mixers are used. With a small consumption of compound feed by the farm, its independent preparation will be the most profitable due to the reduction of time and costs for transportation and storage of finished mixtures. The use of the raw material base of an agricultural enterprise makes it possible to prepare compound feeds that most fully take into account the need of animals for nutrients. It is preferable to use horizontal mixers since they allow to obtain combined feeds with a higher uniformity of component distribution. Experimental studies were conducted in 2021-2022. As the result, there have been obtained mathematical models of the working process of a horizontal mixer, according to which two-dimensional response surfaces were constructed and optimal operating parameters were determined taking into account various design and technological factors. The best mixing quality of 94 % is achieved when the mixing chamber is loaded by 50 %, the rotation speed of the mixer shaft is 13 min-1, the mixing time is 18 minutes. The throughput value reaches the highest value of 2.3 t/h with the amount of material in the mixing chamber of 75 % and the working time of the mixer of 12 minutes, while the rotation speed of the shaft of the combined screw is 17.2 min-1. This allows to reduce labor and energy costs for the development and manufacture of new mixers with belt working bodies and to obtain high-quality feed with minimal costs.


  • Open Access

    Theoretical Studies of the Interaction between Screw Surface and Material in the Mixer

    by Andrzej Marczuk, Vasily Sysuev, Alexey Aleshkin, Petr Savinykh, Nikolay Turubanov, Andrzej Tomporowski

    Mixing is one of the most commonly used processes in food, animal feed, chemical, cosmetic, etc., industries. It is supposed to provide high-quality homogenous, nutritious mixtures. To provide appropriate mixing of materials while maintaining the process high efficiency and low energy consumption it is crucial to explore and describe the material flow caused by the movement of mixing elements and the contact between particles. The process of mixing is also affected by structural features of the machine components and the mixing chamber, speed of mixing, and properties of the mixed materials, such as the size of particles, moisture, friction coefficients. Thus, modeling of the phenomena that accompany the process of mixing using the above-listed parameters is indispensable for appropriate implementation of the process. The paper provides theoretical power calculations that take into account the material speed change, the impact of the material friction coefficient on the screw steel surface and the impact of the friction coefficient on the material, taking into account the loading height of the mixing chamber and the chamber loading value. Dependencies between the mixer power and the product degree of fineness, rotational speed of screw friction coefficients, the number of windings per length unit, and width of the screw tape have been presented on the basis of a developed model. It has been found that power increases along with an increase in the value of these parameters. Verification of the theoretical model indicated consistence of the predicted power demand with the power demand determined in tests performed on a real object for values of the assumed, effective loading, which was 65–75%.


  • Open Access

    Improving efficiency of horizontal ribbon mixer by optimizing its constructional and operational parameters

    by Marczuk Andrzej, Wojciech Misztal, Petr Savinykh, Nikolay Turubanov, Alexey Isupov, Dmitry Zyryanov

    The homogeneity of mixing various feed mixture ingredients and the reliability of mixers directly depend on the constructional features of mixing devices and operational parameters of their work. This article presents a theoretical underpinning for the structural (design) specifications of a horizontal ribbon auger mixer (blender) with regard to the fulfilment of the condition when the material is transported by auger tapes in different directions, ensuring the efficient mixing of the feed mixture ingredients and timely material unloading from the mixer tank (hopper). The performed optimization of the structural and operational specifications as a result of experimental studies has allowed to increase the reliability of the mixer and to determine the homogeneity coefficient of the finished product, which reaches its the highest value of 94.13% with the forward direction of rotation of the mixer movable operating elements, when mixing time is 13 minutes and when the tank load is 52.4% of its volume.