Hiroko Fujii
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hiroko Fujii has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Junko Umeda
Joining and Welding Research Institute, Osaka University
2 shared publications - Katsuyoshi Kondoh
Joining and Welding Research Institute, Osaka University
2 shared publications - Ammarueda Issariyapat
Joining and Welding Research Institute, Osaka University, 11–1 Mihogaoka, Ibaraki, Osaka 567–0047, Japan
1 shared publication - Lei Jia
School of Materials Science and Engineering, Xi’an University of Technology, Xi’an 710048, China
1 shared publication - Nodoka Nishimura
Department of Mechanical Engineering, Osaka University, Suita, Osaka 5670047, Japan
1 shared publication - Ryota Takizawa
Graduate School of Engineering, Osaka University, Suita 565-0871, Japan
1 shared publication
Latest Publications
- Open Access
- 12 October 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (10) , 254
Tribological Behavior of Titanium-Sintered Composites with Ring-Shaped TiN Dispersoids
The wide applicability of titanium (Ti) has prompted the analysis to improve its mechanical strength through the addition of different alloying elements. Among these, Ti materials with pre-mixed pure Ti and titanium nitride (TiN) powders as the starting materials have exhibited improved mechanical properties and tribological performance. In this study, the tribological properties of Ti matrix composites with ring-shaped TiN dispersoids were evaluated. The materials were fabricated from pre-mixed pure Ti powder and core–shell structured Ti–(N) powder, which were prepared by heat treatment at 1273 K under N2 gas. The tribological behavior of the Ti–TiN composites was studied by varying the applied load using a ball-on-disk wear test under oil lubrication conditions. The initial familiarity period of the Ti–TiN composites decreased. Subsequently, compared to the pure Ti specimen employed as a reference material, the friction coefficient was significantly lower and more stable. This is attributed to the ring-shaped, hard TiN dispersoids, which prevented the adhesion phenomenon and improved the oil film formability owing to the increase in microhardness and abrasive wear resistance of the nitrogen solid solution in the core region.
- 12 October 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (10) , 254
Open AccessTribological Behavior of Titanium-Sintered Composites with Ring-Shaped TiN Dispersoids
The wide applicability of titanium (Ti) has prompted the analysis to improve its mechanical strength through the addition of different alloying elements. Among these, Ti materials with pre-mixed pure Ti and titanium nitride (TiN) powders as the starting materials have exhibited improved mechanical properties and tribological performance. In this study, the tribological properties of Ti matrix composites with ring-shaped TiN dispersoids were evaluated. The materials were fabricated from pre-mixed pure Ti powder and core–shell structured Ti–(N) powder, which were prepared by heat treatment at 1273 K under N2 gas. The tribological behavior of the Ti–TiN composites was studied by varying the applied load using a ball-on-disk wear test under oil lubrication conditions. The initial familiarity period of the Ti–TiN composites decreased. Subsequently, compared to the pure Ti specimen employed as a reference material, the friction coefficient was significantly lower and more stable. This is attributed to the ring-shaped, hard TiN dispersoids, which prevented the adhesion phenomenon and improved the oil film formability owing to the increase in microhardness and abrasive wear resistance of the nitrogen solid solution in the core region.
- Open Access
In-Situ Formed Al3Zr Compounds Reinforced Al Composites and Tribological Application
An Al3Zr-reinforced Al matrix composite using metal powders was fabricated via in-situ synthesis in vacuum; these were subjected to a pin-on-disc wear test with a SUS304 disc specimen under oil lubrication. The elemental mixture of Al and ZrH2 particles was sintered in vacuum for the in-situ-formed Al3Zr. ZrH2 particles were thermally decomposed in the reaction with the Al matrix to form hard Al3Zr intermetallic compounds. The friction coefficient and wear volume values of the Al–Al3Zr composites were significantly lower than those of the pure Al specimen. This is attributed to the uniform dispersion of Al3Zr particles in the Al matrix, which prevented the metallurgical bond from falling and blocked the direct contact between the Al matrix and SUS304 disc.
Open AccessIn-Situ Formed Al3Zr Compounds Reinforced Al Composites and Tribological Application
An Al3Zr-reinforced Al matrix composite using metal powders was fabricated via in-situ synthesis in vacuum; these were subjected to a pin-on-disc wear test with a SUS304 disc specimen under oil lubrication. The elemental mixture of Al and ZrH2 particles was sintered in vacuum for the in-situ-formed Al3Zr. ZrH2 particles were thermally decomposed in the reaction with the Al matrix to form hard Al3Zr intermetallic compounds. The friction coefficient and wear volume values of the Al–Al3Zr composites were significantly lower than those of the pure Al specimen. This is attributed to the uniform dispersion of Al3Zr particles in the Al matrix, which prevented the metallurgical bond from falling and blocked the direct contact between the Al matrix and SUS304 disc.