MIMartina Ivanovičová

Martina Ivanovičová

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Martina Ivanovičová has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Ignition of Wood-Based Boards by Radiant Heat

    by Iveta Marková, Martina Ivaničová, Linda Makovická Osvaldová, Jozef Harangózo, Ivana Tureková

    Particleboards (PB) and oriented strand boards (OSB) are commonly used materials in building structures or building interiors. The surface of boards may hence become directly exposed to fire or radiant heat. The aim of this paper is to evaluate the behaviour of uncoated particleboards and OSB exposed to radiant heat. The following ignition parameters were used to observe the process of particleboard and OSB ignition: heat flux intensity (from 43 to 50 kW.m-2) and ignition temperature. The time-to-ignition and mass loss of particleboards and OSB with thicknesses of 12, 15 and 18 mm were monitored and compared. The experiments were conducted on a modified device in accordance with ISO 5657: 1997. Results confirmed thermal degradation of samples. Heat flux had a significant effect on mass loss (burning rate) and time-to-ignition. OSB had higher ignition time than particleboards and the thermal degradation of OSB started later, i.e., at a higher temperature than that of particleboards, but OSB also had higher mass loss than particleboards. The samples yielded the same results above 47 kW.m−2. Thermal analysis also confirmed a higher thermal decomposition temperature of OSB (179 °C) compared to particleboards (146 °C). The difference in mass loss in both stages did not exceed 1%.


  • Open Access

    Experimental Study of the Influence of Selected Factors on the Particle Board Ignition by Radiant Heat Flux

    by Ivana Tureková, Martina Ivanovičová, Jozef Harangózo, Stanislava Gašpercová, Iveta Marková

    Particleboards are used in the manufacturing of furniture and are often part of the interior of buildings. In the event of a fire, particleboards are a substantial part of the fuel in many building fires. The aim of the article is to monitor the effect of radiant heat on the surface of particle board according to the modified procedure ISO 5657: 1997. The significance of the influence of heat flux density and particle board properties on its thermal resistance (time to ignition) was monitored. Experimental samples were used particle board without surface treatment, with thicknesses of 12, 15, and 18 mm. The samples were exposed to a heat flux from 40 to 50 kW·m−2. The experimental results are the initiation characteristics such as of the ignition temperature and the weight loss. The determined factors influencing the time to ignition and weight loss were the thickness and density of the plate material, the density of the radiant heat flux and the distance of the particle board from the radiant source (20, 40, and 60 mm). The obtained results show a significant dependence of the time to ignition on the thickness of the sample and on the heat flux density. The weight loss is significantly dependent on the thickness of the particle board. Monitoring the influence of time to ignition from sample distance confirmed a statistically significant dependence. As the distance of the sample from the source increased, the time to ignition decreased linearly. As the distance of the sample from the source increased, the time to ignition increased.


  • Open Access

    Experimental Study of Oriented Strand Board Ignition by Radiant Heat Fluxes

    by Ivana Tureková, Iveta Marková, Martina Ivanovičová, Jozef Harangózo

    Wood and composite panel materials represent a substantial part of the fuel in many building fires. The ability of materials to ignite when heated at elevated temperatures depends on many factors, such as the thermal properties of materials, the ignition temperature, critical heat flux and the environment. Oriented strand board (OSB) without any surface treatment in thicknesses of 12, 15 and 18 mm were used as experimental samples. The samples were gradually exposed to a heat flux of 43 to 50 kW.m−2, with an increase of 1 kW.m−2. At heat fluxes of 49 kW.m−2 and 50 kW.m−2, the ignition times are similar in all OSB thicknesses, in contrast to the ignition times at lower heat fluxes. The influence of the selected factors (thickness and distance from the heat source) was analysed based on the experimentally obtained data of ignition time and weight loss. The experimentally determined value of the heat flux density was 43 kW.m−2, which represented the critical heat flux. The results show a statistically significant effect of OSB thickness on ignition time.