Euyjin Park
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Euyjin Park has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Hyun-Yong Yu
School of Electrical Engineering, Korea University, Seoul, South Korea
8 shared publications - Seung-Geun Jung
School of Electrical Engineering, Korea University, Seoul, South Korea
4 shared publications Seung-Hwan Kim
Center of Spintronics
4 shared publicationsJong-Hyun Kim
Department of Semiconductor Systems Engineering
3 shared publicationsKyu-Hyun Han
School of Electrical Engineering
3 shared publicationsSeong-Ji Min
School of Electrical Engineering
3 shared publications
Latest Publications
- 15 October 2024
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 18 (43) , 29771-29778
Quasi-Zero-Dimensional Source/Drain Contact for Fermi-Level Unpinning in a Tungsten Diselenide (WSe2) Transistor: Approaching Schottky–Mott Limit
Two-dimensional (2D) transition metal dichalcogenides (TMDCs) known for their exceptional electrical and optical properties have emerged as promising channel materials for next-generation electronics. However, as strong Fermi-level pinning (FLP) between the metal and the 2D TMDC material at the source/drain (S/D) contact decides the Schottky barrier height (SBH), the transistor polarity is fixed to a certain type, which remains a challenge for the 2D TMDC field-effect transistors (FETs). Here, a S/D contact structure with a quasi-zero-dimensional (quasi-0D) contact interface, in which the dimensionality reduction effect alleviates FLP, was developed to gain controllability over the polarity of the 2D TMDC FET. As a result, conventional metal contacts on the WSe2 FET showed n-type characteristics due to strong FLP (pinning factor of 0.06) near the conduction band, and the proposed quasi-0D contact enabled by the Ag conductive filament on the WSe2 FET exhibited p-type characteristics with a SBH very close to the Schottky-Mott rule (pinning factor of 0.95). Furthermore, modeling of Schottky barriers of conventional contacts, one-dimensional (1D) contacts, and quasi-0D contacts revealed that the SBH of the quasi-0D contact is relatively less subject to interface dipoles that induce FLP, owing to more rapid decaying of dipole energy. The proposed contact in this study provided a method that progressed beyond the alleviation of FLP to achieve controllable polarity. Moreover, reducing the contact dimensionality to quasi-0D will enable high compatibility with the further scaled-down nanoscale device contact structure.
- 15 October 2024
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 18 (43) , 29771-29778
Quasi-Zero-Dimensional Source/Drain Contact for Fermi-Level Unpinning in a Tungsten Diselenide (WSe2) Transistor: Approaching Schottky–Mott Limit
Two-dimensional (2D) transition metal dichalcogenides (TMDCs) known for their exceptional electrical and optical properties have emerged as promising channel materials for next-generation electronics. However, as strong Fermi-level pinning (FLP) between the metal and the 2D TMDC material at the source/drain (S/D) contact decides the Schottky barrier height (SBH), the transistor polarity is fixed to a certain type, which remains a challenge for the 2D TMDC field-effect transistors (FETs). Here, a S/D contact structure with a quasi-zero-dimensional (quasi-0D) contact interface, in which the dimensionality reduction effect alleviates FLP, was developed to gain controllability over the polarity of the 2D TMDC FET. As a result, conventional metal contacts on the WSe2 FET showed n-type characteristics due to strong FLP (pinning factor of 0.06) near the conduction band, and the proposed quasi-0D contact enabled by the Ag conductive filament on the WSe2 FET exhibited p-type characteristics with a SBH very close to the Schottky-Mott rule (pinning factor of 0.95). Furthermore, modeling of Schottky barriers of conventional contacts, one-dimensional (1D) contacts, and quasi-0D contacts revealed that the SBH of the quasi-0D contact is relatively less subject to interface dipoles that induce FLP, owing to more rapid decaying of dipole energy. The proposed contact in this study provided a method that progressed beyond the alleviation of FLP to achieve controllable polarity. Moreover, reducing the contact dimensionality to quasi-0D will enable high compatibility with the further scaled-down nanoscale device contact structure.
- 23 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 44 (7) , 1040-1043
Excellent Improvement of Contact Resistivity and Thermal Stability for High Temperature Process After Silicidation of TiSi2 Through Ta Interlayer for Diffusion Barrier
Titanium Silicide (TiSi 2 is a primary contact material with low-resistance contact characteristics used in nanodevices. However, the rapid scaling trend requires further improvement to achieve both high thermal stability and low contact resistivity. Herein, a method for simultaneously improving the contact resistivity and thermal stability of the TiSi 2 /Si interface is proposed by inserting a Ta interlayer into Ti/p-Si. The Ta-interlayered TiSi 2 (Ta IL TiSi 2 ) achieves an improved contact resistivity by approximately 7.9 times compared to that without the Ta interlayer. This remarkable improvement is due to the smooth contact morphology resulting from the suppressed excess diffusion of Ti and Si and dopant segregation at the TiSi 2 /Si interface. Particularly, because additional reaction during post annealing is minimized by the Ta interlayer, Ta IL TiSi 2 shows a low sheet resistance of $3.71~\Omega /\Box $ even after post annealing at 600 °C & 30 min, which is much lower than the conventional TiSi 2 scheme under the same annealing conditions. These results are expected to provide insights into state-of-the-art CMOS-based devices that require both low contact resistivity and better thermal margins.
- 23 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 44 (7) , 1040-1043
Excellent Improvement of Contact Resistivity and Thermal Stability for High Temperature Process After Silicidation of TiSi2 Through Ta Interlayer for Diffusion Barrier
Titanium Silicide (TiSi 2 is a primary contact material with low-resistance contact characteristics used in nanodevices. However, the rapid scaling trend requires further improvement to achieve both high thermal stability and low contact resistivity. Herein, a method for simultaneously improving the contact resistivity and thermal stability of the TiSi 2 /Si interface is proposed by inserting a Ta interlayer into Ti/p-Si. The Ta-interlayered TiSi 2 (Ta IL TiSi 2 ) achieves an improved contact resistivity by approximately 7.9 times compared to that without the Ta interlayer. This remarkable improvement is due to the smooth contact morphology resulting from the suppressed excess diffusion of Ti and Si and dopant segregation at the TiSi 2 /Si interface. Particularly, because additional reaction during post annealing is minimized by the Ta interlayer, Ta IL TiSi 2 shows a low sheet resistance of $3.71~\Omega /\Box $ even after post annealing at 600 °C & 30 min, which is much lower than the conventional TiSi 2 scheme under the same annealing conditions. These results are expected to provide insights into state-of-the-art CMOS-based devices that require both low contact resistivity and better thermal margins.
- Open Access
- 13 April 2023
- Published by Elsevier in Materials Today Advances
- Vol. 18
Effective threshold voltage modulation technique for steep-slope 2D atomic threshold switching field-effect transistor
- 13 April 2023
- Published by Elsevier in Materials Today Advances
- Vol. 18
Open AccessEffective threshold voltage modulation technique for steep-slope 2D atomic threshold switching field-effect transistor
- Open Access
- 12 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 41112-41118
Device Design Guidelines of 3-nm Node Complementary FET (CFET) in Perspective of Electrothermal Characteristics
For the first time, device design guidelines for a 3-nm node complementary field-effect transistor (CFET), which vertically stacks n-type and p-type nanosheet MOSFETs with a shared gate, are investigated using calibrated 3-D technology computer-aided design (TCAD). Here, the optimal device dimensions of the CFETs for better inverter performance and thermal characteristics are studied. The electrothermal performance are investigated for various vertical dimension parameters of CFET, such as the number of stacked channels, vertical distance between nanosheet channels (D nsh ), distance of n/pMOS separation (D n/p ), and channel thicknesses (T nsh ). The results show that, unlike conventional CMOS, the reduction of D nsh and D n/p of CFET can effectively improve inverter performance without severe thermal degradation, although other dimensional parameters trigger a severe trade-off between different electrothermal parameters. The reduction of D nsh and D n/p decreases C eff with a lower metal via the height and gate fringing effect. However, the reduction in D nsh and D n/p does not change R eff ; therefore, both the operation frequency ( $f$ ) and power-product delay (PDP) can be improved. In the case of thermal characteristics, the reduction of D nsh and D n/p slightly increases both T max and R th because of thermal coupling but is negligible. Therefore, the reduction of D nsh and D n/p will be a key technique for the development of sub-3-nm CFET.
- 12 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 41112-41118
Open AccessDevice Design Guidelines of 3-nm Node Complementary FET (CFET) in Perspective of Electrothermal Characteristics
For the first time, device design guidelines for a 3-nm node complementary field-effect transistor (CFET), which vertically stacks n-type and p-type nanosheet MOSFETs with a shared gate, are investigated using calibrated 3-D technology computer-aided design (TCAD). Here, the optimal device dimensions of the CFETs for better inverter performance and thermal characteristics are studied. The electrothermal performance are investigated for various vertical dimension parameters of CFET, such as the number of stacked channels, vertical distance between nanosheet channels (D nsh ), distance of n/pMOS separation (D n/p ), and channel thicknesses (T nsh ). The results show that, unlike conventional CMOS, the reduction of D nsh and D n/p of CFET can effectively improve inverter performance without severe thermal degradation, although other dimensional parameters trigger a severe trade-off between different electrothermal parameters. The reduction of D nsh and D n/p decreases C eff with a lower metal via the height and gate fringing effect. However, the reduction in D nsh and D n/p does not change R eff ; therefore, both the operation frequency ( $f$ ) and power-product delay (PDP) can be improved. In the case of thermal characteristics, the reduction of D nsh and D n/p slightly increases both T max and R th because of thermal coupling but is negligible. Therefore, the reduction of D nsh and D n/p will be a key technique for the development of sub-3-nm CFET.
- Open Access
- 20 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 10, 78-82
Performance Analysis on Complementary FET (CFET) Relative to Standard CMOS With Nanosheet FET
For the first time, by using 3-D TCAD, the advantage of using complementary FET (CFET), which has vertically stacked nanosheet nFET and pFET with shared gate, is compared to standard CMOS with nanosheet FETs in perspective of CMOS inverter performance. The comparative study on CMOS operation was performed between CFET and standard CMOS in 3-nm technology node. The results indicate that, when both devices have identical DC electrical characteristics, using CFET can increase the frequency by ~2.3% in iso-power and decrease power by ~7.3% in iso-frequency compared to the standard CMOS with separate n/pFETs while effectively reducing the area by ~55%. It is also investigated that such results are due to the approximately 4.5% low effective capacitance (C eff ) of the CFET compared to the standard CMOS. This low C eff of CFET arises from the stacked structure, which causes the gate-fringe electric field overlap and short via pitch between nFET and pFET. Furthermore, the performance of CFET by different n/pFET separation distances, channel lengths, and widths are analyzed. This study can provide critical insight into the performance improvement by using CFET for sub 3-nm technology.
- 20 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 10, 78-82
Open AccessPerformance Analysis on Complementary FET (CFET) Relative to Standard CMOS With Nanosheet FET
For the first time, by using 3-D TCAD, the advantage of using complementary FET (CFET), which has vertically stacked nanosheet nFET and pFET with shared gate, is compared to standard CMOS with nanosheet FETs in perspective of CMOS inverter performance. The comparative study on CMOS operation was performed between CFET and standard CMOS in 3-nm technology node. The results indicate that, when both devices have identical DC electrical characteristics, using CFET can increase the frequency by ~2.3% in iso-power and decrease power by ~7.3% in iso-frequency compared to the standard CMOS with separate n/pFETs while effectively reducing the area by ~55%. It is also investigated that such results are due to the approximately 4.5% low effective capacitance (C eff ) of the CFET compared to the standard CMOS. This low C eff of CFET arises from the stacked structure, which causes the gate-fringe electric field overlap and short via pitch between nFET and pFET. Furthermore, the performance of CFET by different n/pFET separation distances, channel lengths, and widths are analyzed. This study can provide critical insight into the performance improvement by using CFET for sub 3-nm technology.
- 15 December 2021
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 3 (12) , 5584-5591
Analysis of the Thermal Degradation Effect on a HfO2-Based Memristor Synapse Caused by Oxygen Affinity of a Top Electrode Metal and on a Neuromorphic System
- 15 December 2021
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 3 (12) , 5584-5591
Analysis of the Thermal Degradation Effect on a HfO2-Based Memristor Synapse Caused by Oxygen Affinity of a Top Electrode Metal and on a Neuromorphic System
- 23 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (5) , 2275-2280
Enhancement of DRAM Performance by Adopting Metal–Interlayer–Semiconductor Source/Drain Contact Structure on DRAM Cell
The effects of a metal-interlayer-semiconductor (MIS) source/drain (S/D) contact structure on a dynamic random access memory (DRAM) cell transistor are investigated using 3-D technology computer-aided design simulation. When the MIS S/D contact structure is used in a DRAM cell, the retention time increases by approximately 16.22 times when compared with that of the device using the metal-semiconductor (MS) S/D contact structure owing to the lowered S/D doping concentration, leading to a decrement of the gate-induced drain leakage. Furthermore, the write time and charge-sharing time, respectively, are approximately 0.74 and 0.69 times shorter when compared with the device using the MS S/D contact structure owing to better ohmic characteristics, which increase the drain current during the write/read operations. Thus, the MIS S/D contact structure can effectively enhance the retention and write/read characteristics of a DRAM cell, and it can be a promising S/D contact alternative for the DRAM cell in the sub-2y-nm technology node.
- 23 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (5) , 2275-2280
Enhancement of DRAM Performance by Adopting Metal–Interlayer–Semiconductor Source/Drain Contact Structure on DRAM Cell
The effects of a metal-interlayer-semiconductor (MIS) source/drain (S/D) contact structure on a dynamic random access memory (DRAM) cell transistor are investigated using 3-D technology computer-aided design simulation. When the MIS S/D contact structure is used in a DRAM cell, the retention time increases by approximately 16.22 times when compared with that of the device using the metal-semiconductor (MS) S/D contact structure owing to the lowered S/D doping concentration, leading to a decrement of the gate-induced drain leakage. Furthermore, the write time and charge-sharing time, respectively, are approximately 0.74 and 0.69 times shorter when compared with the device using the MS S/D contact structure owing to better ohmic characteristics, which increase the drain current during the write/read operations. Thus, the MIS S/D contact structure can effectively enhance the retention and write/read characteristics of a DRAM cell, and it can be a promising S/D contact alternative for the DRAM cell in the sub-2y-nm technology node.
- 20 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (3) , 1340-1345
LER-Induced Random Variation–Immune Effect of Metal-Interlayer–Semiconductor Source/Drain Structure on N-Type Ge Junctionless FinFETs
Herein, the line-edge roughness (LER)-induced random performance variation-immune effect of metal-interlayer-semiconductor (MIS) source/drain (S/D) in 7 nm n-type Ge (n-Ge) junctionless field-effect transistors (JLFETs) were investigated by 3-D TCAD simulations. Compared to the device without MIS S/D, the n-Ge JLFET with MIS S/D could effectively reduce the Ge fin doping concentration while maintaining the performance. It was demonstrated analytically that the reduced Ge fin doping concentration of the device with MIS S/D, compared to the device without MIS S/D, decreased the LER-induced random performance variations of the n-Ge JLFET; the standard deviations were reduced to ~0.0318 V for V th (reduced by ~51.6%), 4.89 × 10 -6 A/μm for Ion (reduced by 92.1%), 1.44 × 10 -9 A/μm for I off (reduced by 93.7%), 1.27 mV/dec for SS (reduced by 23.1%), and 5.40 mV/V for drain-induced barrier lowering (DIBL) (reduced by ~30.8%). In addition, LER-induced random performance variation was investigated in terms of scaling down fin widths. The results provided critical insight into the variability reduction of the 7 nm n-Ge JLFETs.
- 20 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (3) , 1340-1345
LER-Induced Random Variation–Immune Effect of Metal-Interlayer–Semiconductor Source/Drain Structure on N-Type Ge Junctionless FinFETs
Herein, the line-edge roughness (LER)-induced random performance variation-immune effect of metal-interlayer-semiconductor (MIS) source/drain (S/D) in 7 nm n-type Ge (n-Ge) junctionless field-effect transistors (JLFETs) were investigated by 3-D TCAD simulations. Compared to the device without MIS S/D, the n-Ge JLFET with MIS S/D could effectively reduce the Ge fin doping concentration while maintaining the performance. It was demonstrated analytically that the reduced Ge fin doping concentration of the device with MIS S/D, compared to the device without MIS S/D, decreased the LER-induced random performance variations of the n-Ge JLFET; the standard deviations were reduced to ~0.0318 V for V th (reduced by ~51.6%), 4.89 × 10 -6 A/μm for Ion (reduced by 92.1%), 1.44 × 10 -9 A/μm for I off (reduced by 93.7%), 1.27 mV/dec for SS (reduced by 23.1%), and 5.40 mV/V for drain-induced barrier lowering (DIBL) (reduced by ~30.8%). In addition, LER-induced random performance variation was investigated in terms of scaling down fin widths. The results provided critical insight into the variability reduction of the 7 nm n-Ge JLFETs.