PRPavel Razgovorov

Pavel Razgovorov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Pavel Razgovorov has a total of 38 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Strength of gypsum-based building composites by additives of linen fiber

    by P. B. Razgovorov, V. B. Dobrokhotov, M. O. Bakanov, V. A. Kozhukhov, N. I. Orlov

    The strength properties of gypsum composites modified under introducing flax fibers - vegetable raw materials of the Altai Territory are considered. It is shown that linen fiber, under scientifically substantiated conditions of its preparation, can serve as a promising raw material to obtain molding gypsum masses, suitable after their hardening for construction work inside buildings and structures. A difference was found in the physical and mechanical properties of composites based on gypsum of grades G-3 and G-16, characterized by varied structural density. The effect of the degree of grinding of the reinforcing additive on the strength properties of gypsum composites and materials based thereon has been established. Medium or fine grinding of the linen fiber with a length of ≤3 mm on a disk mill, while limiting its addition in a gypsum composition G-3 B II increases its flexural strength up to 20-50%, and its compressive strength - up to 80%. It was revealed that the introduction of >1% of reinforcing fiber into high-strength gypsum of G-16 grade is impractical. Otherwise, the effect of excessive porosity begins to prevail over the effect of environmental friendliness, cheaper and expected reduction in the material consumption of the building composite.

  • Open Access

    Rational enclosing structures of wooden buildings: heat and mass transfer and environmental potential

    by Sergey Fedosov, V. Fedoseev, Pavel Razgovorov, V. Voronov

    The paper discusses the development and improvement of rational types of enclosing structures for wooden buildings, taking into account the coupled heat and mass transfer processes occurring in them and environmental safety. A comparative analysis of typical structures reduced to a unified standard thermal resistance is presented. It has been revealed that timber structures have a negative carbon footprint at the production stage (–116.2 kg CO₂‑equiv.·m⁻²) due to carbon sequestration. To ensure durability and realize their environmental potential, the need for mathematical modeling of unsteady heat and mass transfer based on the classical theory of Academician of the RAACS S.V. Fedosov is substantiated. The developed algorithm, employing the integral Laplace transform and similarity theory, makes it possible to obtain an analytical solution in the form of rapidly convergent series. This solution serves as a reliable basis for the development of numerical methods for experimental studies of the properties of materials and for the creation of algorithms for monitoring the technical condition of timber structures during their service life.

  • Open Access

    The effect of flax fiber additives on the strength of gypsum-based construction composites

    by Pavel Razgovorov, Vladimir Dobrokhotov, Viktor Kozhukhov, Maksim Bakanov, Ilya Davydov

    The paper considers the prospects of using flax fibre additives to improve the physical and mechanical properties of building composites. The authors note that a regulated approach to the preparation of reinforcing additives from plant raw materials contributes to improving the performance characteristics of gypsum-based building materials. It has been established that the addition of 1-3% flax fibre with a moisture content of 18-20% to G3 gypsum significantly (by 83%) increases the flexural tensile strength of samples obtained from hardened gypsum mixtures and more than doubles the compressive strength of finished composites. The authors identified a positive effect of the degree of preliminary grinding of flax fibre (up to 50-70° on the Shopper-Rigler scale), mixed with gypsum (G3 grade) and water, on achieving the strengthening effect of the finished composites. The development of such materials complies with modern regulatory and legislative requirements in the field of sustainable construction and environmental protection.

  • Extraction of Copper(II) Ions with a Sorbent Based on Cellulose and Sodium Alginate Modified with Guanidine

    by A. R. Sofronov, T. E. Nikiforova, V. A. Kozlov, P. B. Razgovorov

    A new composite sorbent has been developed based on microcrystalline cellulose and sodium alginate modified with guanidine hydrochloride. Modification was performed via the stage of oxidation of polysaccharides with sodium metaperiodate, forming dialdehyde cellulose and sodium dialdehyde alginate, followed by the addition of guanidine amino groups to the aldehyde groups. A comparative analysis of the sorption properties of the modified sorbent containing amino groups with those of microcrystalline cellulose showed that the sorption efficiency of copper ions depends on the nature of sorption sites. When studying the sorption kinetics of Cu(II) cations, it was found that the results of the kinetic experiment are most correctly described within the framework of the pseudo-second-order model. The experimental isotherms of sorption of copper(II) ions from aqueous solutions with the modified sorbent and microcrystalline cellulose are well described by the Langmuir equation. As a result of linearization of isotherms, it was found that the modified sorbent surpasses microcrystalline cellulose in terms of the maximum sorption capacity by approximately an order of magnitude. The changes in the sorption capacity of the developed sorbent compared to the original are due to the appearance of new sorption sites in its structure, which is confirmed by scanning electron microscopy and IR spectroscopy data.

  • Comprehensive mathematical modelling in the management of physical and chemical processes during the transportation of concrete mixtures

    by Sergey Fedosov, Maksim Bakanov, Ol'GA Aleksandrova, Pavel Razgovorov, Ilya Kuznetsov

    The paper presents a comprehensive mathematical model and adaptive control system for predicting and maintaining the quality of concrete mix during its transportation in the drums of truck mixers. The purpose of the study is to bridge the gap between detailed physical and mathematical models and operational control tasks in dynamic conditions. The developed software package demonstrated high accuracy in predicting hydration kinetics (RMSD = 1.0%) and moisture content (RMSD = 2.0%). It has been shown that optimising the control action allows the drum rotation speed to be reduced by 86.7% (to 2 min-1). This results in an 85% reduction in the cost function and an estimated 42% reduction in energy consumption without compromising the quality of the mixture. A comprehensive approach makes it possible to move from passive modelling to active control of concrete mix quality during transportation. This is confirmed by the analytical dependencies identified and the results of computational experiments.


  • Open Access

    Design and construction of charging stations in the conditions of street and road network of a megalopolis in Russia

    by Albert Burgonutdinov, Pavel Razgovorov, Artemy Korovka, Igor' Vikulin

    The restructuring of the global market has resulted in a saturation of various sectors of the economy with vehicles with new devices including compact energy storage. In 2021, the ‘Concept for the Development of Production and Use of Electric Road Transport in the Russian Federation for the Period until 2030’ was approved. It requires significant changes in road infrastructure. The construction of charging station networks, due to the lack of formed regulatory documents, poses a number of challenges and new tasks for the development of roads in domestic metropolises. The paper considers aspects concerning the development of public transport infrastructure and the organisation of uninterrupted electric bus traffic in the design of urban roads on the example of the city of Moscow.

  • Open Access

    Concentration of heavy metal ions from aqueous media under dynamic conditions using a composite sorbent based on chitosan and silica

    by V. A. Gabrin, T. E. Nikiforova, V. A. Kozlov, P. B. Razgovorov

    Objectives. The study set out to investigate the sorption, toxicological, and regeneration properties of a composite sorbent based on chitosan hydrogel and unsuspended silicon dioxide (chitosan–colloidal silica), which manifest themselves under dynamic conditions of purification of aqueous solutions, as a means of removing heavy metal ions.Methods. The total dynamic exchange capacity of a chitosan–colloidal silica composite sorbent was evaluated under dynamic sorption conditions by passing solutions containing Zn(II), Cd(II), Cu(II), and Cr(III) ions having a concentration of 240–251 mg/L through a fixed sorption bed. The method for determining acute toxicity using daphnia (Daphnia magna Straus) is based on the direct calculation of the mortality of daphnia exposed to toxic substances contained in the test aqueous extract in comparison with a reference culture in samples that do not contain toxic substances. The regeneration ability of the sorbent was assessed by counting the number of sorption–desorption cycles using 0.1 M NaOH and 0.1 M NaHCO3 eluents, as well as aqueous solutions of H2O2 (1 and 3%).Results. The effectiveness of the chitosan–colloidal silica composite sorbent in the process of dynamic purification of aqueous media to remove Cu(II), Zn(II), Cd(II), and Cr(III) ions was established. After determining the times of ion breakthrough and saturation of the developed sorbent, its dynamic exchange capacity was calculated by processing the kinetic curves of sorption of heavy metal ions under dynamic conditions. The results of regeneration of the sorbent were presented in the context of the possibility of its reuse. It is shown that the sorbent can withstand up to five sorption–desorption cycles while maintaining a level copper cation extraction above 90%.Conclusions. Analysis of the kinetic curves demonstrated that the driving force behind the removal of heavy metals from aqueous media by means of the obtained sorbent is the external diffusion mass transfer of ions from the mobile phase of the solution. Biotesting of samples showed that the developed chitosan-based sorbent does not have acute toxicity.