YCYun Chen

Yun Chen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yun Chen has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Identification of Ocean Thermal Energy Conversion Heat Exchange Model Based on Long Short-Term Memory Network and Heat Exchange Efficiency Improvement Study

    by Yanjun Liu, Xiu You, Mingqian Tian, Tianxu Zhang, Yun Chen, Yanni Yu

    The core of ocean thermal energy conversion (OTEC) is the transfer and conversion of heat energy, and the heat exchanger is a key component of the heat transfer between the surface warm seawater and the lower cold seawater. The working fluid has a significant impact on the efficiency of the entire cycle in the temperature difference cycle. This study aimed to improve heat exchange efficiency. The article studied heat exchangers, used R134a as the circulating medium, and applied ANSYS-FLUENT 2020R2 simulation software to analyze the variation in heat transfer coefficients. We obtained the trend in the heat transfer coefficient of the heat exchanger with the shape of an elliptical tube under the condition of ocean temperature difference cycles. Then we used a long short-term memory network and Adam optimization algorithm to establish the prediction model. The NSGA-II 11 algorithm was used to realize optimization objectives of the highest heat transfer efficiency and the smallest cross-sectional area of heat transfer tubes along the X and Y directions. Finally, the parameters of the evaporator and condenser ultimately resulted in three optimal solutions. The results of this study can provide a certain theoretical basis and reference value for the efficiency analysis, structure optimization, and experimental research of the subsequent ocean differential circulation heat transfer.


  • Open Access

    Experimental Research and Improved Neural Network Optimization Based on the Ocean Thermal Energy Conversion Experimental Platform

    by Yanni Yu, Mingqian Tian, Yanjun Liu, Beichen Lu, Yun Chen

    With the progress of research on ocean thermal energy conversion, the stabI have checked and revised all. le operation of ocean thermal energy conversion experiments has become a problem that cannot be ignored. The control foundation for stable operation is the accurate prediction of operational performance. In order to achieve accurate prediction and optimization of the performance of the ocean thermal energy conversion experimental platform, this article analyzes the experimental parameters of the turbine based on the basic experimental data obtained from the 50 kW OTEC experimental platform. Through the selection and training of experimental data, a GA-BP-OTE (GBO) model that can automatically select the number of hidden layer nodes was established using seven input parameters. Bayesian optimization was used to complete the optimization of hyperparameters, greatly reducing the training time of the surrogate model. Analyzing the prediction results of the GBO model, it is concluded that the GBO model has better prediction accuracy and has a very low prediction error in the prediction of small temperature changes in ocean thermal energy, proving the progressiveness of the model proposed in this article. The dual-objective optimization problem of turbine grid-connected power and isentropic efficiency is solved. The results show that the change in isentropic efficiency of the permeable device is affected by the combined influence of the seven parameters selected in this study, with the mass flow rate of the working fluid having the greatest impact. The MAPE of the GBO model turbine grid-connected power is 0.24547%, the MAPE of the turbine isentropic efficiency is 0.04%, and the MAPE of the turbine speed is 0.33%. The Pareto-optimal solution for the turbine grid-connected power is 40.1792 kW, with an isentropic efficiency of 0.837439.


  • Open Access

    Design and Experimental Study of 50 kW Ocean Thermal Energy Conversion Test Platform Based on Organic Rankine Cycle

    by Beichen Lu, Yanjun Liu, Xiaoyu Zhai, Li Zhang, Yun Chen

    In recent years, clean and renewable energy sources have received much attention to balance the contradiction between resource needs and environmental sustainability. Among them, ocean thermal energy conversion (OTEC), which consists of surface warm seawater and deep cold seawater, can rely on thermal cycling to generate electricity and has great potential in alleviating the energy crisis. In this paper, the design and experiment study of a 50 kW OTEC platform is proposed. Thermodynamic modeling, calculation, optimization, and engineering calibration of the system were carried out, and the thermal efficiency reached 2.63% to meet the power generation demand. Experiments were also carried out by using a heat pump unit to simulate hot and cold seawater environments, and data on the stable operation of the system were obtained, with the grid-connected power reaching 47.5 kW and a thermal efficiency of 2.46%. The accuracy of the design scheme is verified, and the theoretical basis and data support are provided for the practical development and application of ocean thermal energy conversion.


  • Open Access

    Parameter Optimization and Performance Research: Radial Inflow Turbine in Ocean Thermal Energy Conversion

    by Yiming Wang, Yun Chen, Gang Xue, Tianxu Zhang, Yanjun Liu

    Combining one-dimensional parameter optimization and three-dimensional modeling optimization, a 30 kW radial inflow turbine for ocean thermal energy conversion was designed. In this paper, the effects of blade tip clearance, blade number, twist angle, and wheel–diameter ratio on the radial inflow turbine were analyzed. The results show that the model prediction method based on 3D numerical simulation data can effectively complete secondary optimization of the radial turbine rotor. The prediction model can be used to directly obtain the optimal modeling parameter of the rotor. The tip clearance, blade number, twist angle, wheel–diameter ratio, and shaft efficiency were found to be 0.273 mm, 16, 43.378°, 0.241, and 88.467%, respectively. The optimized shaft efficiency of the turbine was found to be 2.239% higher than the one-dimensional design result, which is of great significance in reducing the system’s power generation costs and promoting the application of this approach in engineering power generation using ocean thermal energy.


  • Open Access

    Optimization Design of the Organic Rankine Cycle for an Ocean Thermal Energy Conversion System

    by Xiaowei Yang, Yanjun Liu, Yun Chen, Li Zhang

    This study selects five parameters as decision variables for the optimization design of an ocean thermal energy conversion system, including the evaporating temperature, the condensing temperature, the pinch-point temperature difference between the evaporator and condenser, and the working fluid flow rate. The optimization goal is to maximize the net output power per unit area and the exergy efficiency. The final scheme is comprehensively screened out from the Pareto solution set through some evaluation indexes. Finally, this study also analyzes the effects of four decision variables on the optimization objectives and the evaluation indexes. This study finds that evaporating temperature and condensing temperature have similar effects on the two objective functions. However, the pinch-point temperature difference has different effects on them. The back work ratio is obviously affected by the condensing temperature. A small pinch-point temperature difference is beneficial and improves the performance of an ocean thermal energy conversion system. The effects of evaporating temperature and condensing temperature on the investment cost per unit net output power are roughly similar to those on the net output power per unit heat exchange area. However, the effects of the pinch-point temperature difference on the two performance aspects are inconsistent.


  • Open Access

    Operation Control and Performance Analysis of an Ocean Thermal Energy Conversion System Based on the Organic Rankine Cycle

    by Xiaowei Yang, Yanjun Liu, Yun Chen, Li Zhang

    The development and utilization of marine renewable energy is an important measure for achieving energy conservation, emissions reduction and carbon neutrality. Ocean thermal energy is the most stable energy among all the types of marine renewable energy. This paper built a simulation model of an ocean thermal energy conversion system based on actual device specifications by Aspen and MATLAB and put forward a corresponding control strategy. The opening control signal of the control valve at the turbine inlet was the condenser inlet pressure in this paper, and the frequency control of the working fluid pump depended on the evaporating pressure and flow rate of the working fluid. This paper analyzed the key operating parameter changes of the system under different working conditions. According to the analysis results, the turbogenerator in this system was able to generate 50 kW power for about 8 months per year. The highest net output power of the Organic Rankine Cycle was 47.3 kW; the highest cycle thermal efficiency was 3.2%.


  • Open Access

    The Shape Optimization and Experimental Research of Heave Plate Applied to the New Wave Energy Converter

    by Zhongliang Meng, Yun Chen, Shizhen Li

    The development and utilization of wave energy is inseparable from the wave energy converter, and its stability is an important condition for operation. Heave is the biggest factor affecting the stable power generation of wave energy converters. The key method to solve this problem is to install a suitable heave plate. Therefore, the design of the heave plate is particularly important. Based on a new type of horizontal rotor wave energy converter, this paper proposes three different shapes of heave plate design schemes and completes the calculation and modeling of the engineering prototype. First, the three types of heave plate devices were numerically simulated using hydrodynamic calculation software to compare their stable performances and verify the feasibility of the scheme. Subsequently, an experimental model was made according to the parameters of the engineering prototype, and a tank experiment was carried out under the same working conditions to further study the influence of the heave plate installation distance on the stability of the wave energy generator. The results showed that when the distance was between 10 mm and 20 mm, the average amplitude change was large, and when the distance was between 20 mm and 30 mm, the average amplitude change was small. Therefore, the installation distance should be between 20 mm and 30 mm. In the case of the same heave plate area and installation distance, the average amplitude of the chamfered heave plate device was smaller than the other two types, indicating that its stability was better. The optimization of the shape and installation distance of the heave plate proposed in this study has obvious effects on improving the stability of the device and provides a reference for the design of the wave energy converter device.


  • Open Access

    Mooring Stability Study for Novel Wave Energy Converter Based on Regular Wave

    by Zhongliang Meng, Yun Chen, Yanjun Liu, Yi Ding

    The mooring system not only plays a vital role in keeping wave energy generators floating stably, but also affects the success of engineering design. Combining wave force theory and the hydrological data obtained from the field measurements of a certain sea area in the Bohai Sea, the Stokes second-order wave theory was adopted to design the mooring system of a new type of power-generating device. At the same time, the study uses the Aqwa software to gather the dynamic data of a power-generating device in a real test, and then makes models and carries out regular wave tests so as to verify the viability of the mooring system and the stability of the whole power-generating device. All of this work will provide a theoretical basis for the manufacture of an engineering prototype and its reliable supply of power.


  • Open Access

    Research on Optimization and Verification of the Number of Stator Blades of kW Ammonia Working Medium Radial Flow Turbine in Ocean Thermal Energy Conversion

    by Yun Chen, Yanjun Liu, Wei Yang, Yiming Wang, Li Zhang, Yongpeng Wu

    Ocean Thermal Energy Conversion (OTEC) is one of the emerging industries of ocean energy and an important link in carbon neutrality. Turbine is a key component of ocean thermal energy conversion, which has an important impact on the performance and energy conversion efficiency of the system. This paper fully considers the application characteristics of ocean thermal energy conversion and the state conversion characteristics of ammonia working fluid. Taking the 100 kW radial inflow turbine in the OTEC application system as an example, based on the design, the turbine is optimized for the key parameters of the turbine stator and the influence of different geometric parameters is analyzed. Subsequently, the optimization results are verified by CFD numerical simulation analysis under different conditions. The results show that the number of stator blades has an important influence on the performance of the turbine. Further optimization studies have shown that through optimization, when the number of stator blades is 33, the internal flow field performance is the best, and the working conditions of the inlet and outlet working fluids are in accordance with the design points without obvious shock wave and reverse flow phenomenon, the efficiency is 89.46%, 3.94% higher than the design value.


  • Open Access

    Three-Dimensional Performance Analysis of a Radial-Inflow Turbine for Ocean Thermal Energy Conversion System

    by Yun Chen, Yanjun Liu, Li Zhang, Xiaowei Yang

    Turbine is one of the key components of the ocean thermal energy conversion system (OTEC), and its aerodynamic performance and geometric dimension affect the performance of the system directly. This paper proposes a design method for the radial inflow turbine suitable for the ocean thermal energy conversion based on the parameter optimization of the ocean thermal energy conversion system. Aiming at the application characteristics of marine thermal energy conversion in a small temperature difference environment and the special thermophysical properties of the organic working fluid in this environment, one-dimensional design and three-dimensional CFD analysis of the turbine is separately done, of which the results were compared. At the same time, the performance of the turbine was verified by changing the inlet and outlet conditions of the radial turbine under the design conditions. The conclusion is that the three-dimensional CFD results of the turbine are in good agreement with the one-dimensional design, and the internal flow field of the turbine is stable, without obvious backflow and eddy current, which meets the application requirements of the ocean thermal energy conversion.