SMSerhii Mazurchuk

Serhii Mazurchuk

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Serhii Mazurchuk has a total of 31 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Identifying patterns in the resistance of thermally modified ash wood to weathering

    by Oleksandra Horbachova, Serhii Mazurchuk, Vasyl Lomaha, Nataliia Buiskykh, Andrii Matviichuk, Nataliia Marchenko

    Weathering of thermally modified wood negatively affects both the appearance of structures and their physical-mechanical characteristics, which further determines their service life. Given this, the object of the study was the resistance of ash wood varying degrees modification to abiotic environmental factors. It was found that the color stability of thermally modified wood samples is higher compared to untreated ones. A decrease in the value of the coordinate L from 68.4 to 33.6 indicates a decrease in lightness, that is darkening of the wood. Analysis of dimensional changes revealed increased swelling for untreated wood and amounted to 7.49 %, and for modified at a temperature of 200 °С – 1.75 %. The difference in shrinkage rates is much smaller – 2.09 % for wood of group III, which is 2 times less than untreated wood. The results confirm that thermal modification makes wood cell walls more hydrophobic by eliminating hydrophilic and hydroxyl groups of hemicelluloses. A linear dependence (R2≈1) of change in the physical characteristics of wood depending on its density due to the degree of modification has been established. Analysis of mechanical properties revealed that thermal modification increases the resistance of wood to compressive across the fibers by 2 times. Therefore, a comprehensive approach to analyzing the impact of weathering on the aesthetic, physical, and mechanical properties of thermally modified wood makes it possible to identify the principles of material stability depending on the treatment schedule. The identified mechanisms of transformation of material parameters contribute to the establishment of optimal parameters of thermal modification, which improve its characteristics. This creates the prerequisites for implementing new technological solutions focused on environmental friendliness and energy efficiency in production


  • Open Access

    Establishment of patterns in the thermal modification of dry pine wood

    by Yuriy Tsapko, Oleksandra Horbachova, Ruslan Likhnyovskyi, Serhii Mazurchuk, Аleksii Tsapko, Nataliia Buiskykh, Andrii Matviichuk, Oksana Slutska, Olena Korolova, Dmytro Khromenkov

    One of the methods of ensuring the durability of dry wood during operation is its thermal modification, which inhibits the life processes of the fungus of the Ceratostomaceae family and leads to a change in its structure and properties. Therefore, the object of research was thermally modified dry pine wood affected by a fungus of the Ceratostomaceae family. Physicochemical studies of changes in the structure of thermally modified dry pine wood showed that the samples have absorption spectra that are characterized by fluctuations of the glucopyranose ring of cellulose and are an indicator of the beginning of destructive processes. At the same time, the data of thermogravimetric analysis show the processes of water loss and decomposition of hemicellulose, cellulose, and lignin, and burning of coke residue. Bending and compressive strength of thermally modified dry pine wood shows that as the wood dries, the strength limit decreases depending on the degree of fungus damage. Namely, with an area of biological damage within 10 %, the strength limit is reduced by more than 1.2 times when modified at 200 °С/3 hours, by more than 1.9 times at 200 °С/6 hours. With an increase in the degree of fungal damage to 30÷50 %, the strength limit decreases by more than 1.6 times when modified at 200 °С/3 hours, by more than 2.1 at 200 °С/6 hours. And when affected by a fungus in the range of 80÷100 %, the wood becomes softer, more plastic, while the bending strength is reduced by 1.7 times, and the compressive strength by 1.16 times. Thermal modification of dry pine wood at 200 °С for 3 hours reduces the level of water absorption by more than 1.5 times, and for 6 hours ‒ by more than 1.7 times. The practical importance is that the results of determining changes in the structure and properties of thermally modified dry pine wood make it possible to establish the scope and conditions of its application


  • Open Access

    Functional assignment of technological accessories for woodworking

    by Yu Tsapko, O. Bondarenko, O. Tsapko, A. Gorbachova, S. Mazurchuk, D Zherebchuk

    Forming a heat and sound insulation board from wood using non-combustible binders can increase the fire protection of the material by forming a protective layer of coke. This will make it possible to develop a new type of fireproof roofing products for building structures. It is not always advisable to treat the surface of a heat and sound insulation board with fireproof coatings, since after prolonged thermal exposure, the combustion stage can be transferred to the interior of the material by smoldering. Therefore, the manufacture of fire-resistant heat- and sound-insulating wood materials, the study of fire protection and the impact of their components on this process is an unresolved component of ensuring the fire resistance of building structures. And, accordingly, they determine the need for such research. The paper presents the results of research into the process of protecting wood wool boards with binders based on fire-resistant coatings. Tests on model samples of a wooden board showed that the material based on wood wool and an inorganic binder is characterized by heat absorption and inhibition of oxidation in the gas and condensed phase and the formation of a thermally protective ceramic layer on the surface of the wood. Experimental studies have confirmed that a material based on wood wool and an inorganic binder at a ratio of 1:1 refers to combustible materials, since its smoldering was recorded during exposure to temperature. So, by thermal action for 90 s, the material ignited and the flame spread over the first three zones for 41 s. On the other hand, an increase in the amount of an inorganic-based binder and the use of an organic-mineral binder does not lead to a material fire. In this case, the maximum temperature of the flue gases was about 120 °C, and the flammability index was 0 due to the decomposition of fire retardants under the influence of temperature with the release of incombustible gases, which inhibit the oxidation of the material and significantly increase the formation of a heat-protective layer of coke on the surface of the material. This leads to inhibition of heat transfer of the high-temperature flame to the material. Due to this, it became possible to determine the conditions of fire resistance of the material by forming a barrier for thermal conductivity. The obtained results indicate the possibility of targeted regulation of high temperature transfer processes to organic material by using special binders for wood products.


  • Open Access

    Determining patterns in the formation of a polymer shell by powder paint on wood surface

    by Yuriy Tsapko, Ruslan Likhnyovskyi, Nataliia Buiskykh, Oleksandra Horbachova, Serhii Mazurchuk, Oles Lastivka, Аleksii Tsapko, Kostiantyn Sokolenko, Andrii Matviichuk

    An issue related to using wood and wood products for building structures is to ensure their stability and durability during operation within wide limits. Therefore, the object of this study was a change in the properties of the polymer shell of powder paint on wood during thermal modification. It is proved that in the process of thermal modification of wood, its structure changes, and accordingly, during the polymerization of powder paint, degassing occurs, which affects the polymer shell. Namely, during the thermal polymerization of powder paint at a temperature of 180 °C for untreated wood, shallow bubbles and craters are characteristic of the formed polymer shell. Instead, a smooth surface is marked for a sample of thermally modified wood. Thermogravimetric analysis data show thermogravimetric curves characterized by the loss of mass of the sample of the original wood with increasing temperature due to the processes of dehydration, destruction of hemicellulose and lignin. This is dehydration, accompanied by the destruction of the pyranose cycle, and carbonization to form a carbon residue and a complex mixture of volatile products. Due to this, bubbles and craters are formed in the polymer shell of the coating. Based on the obtained results of adhesion of the polymer shell on wood, which is treated with a mixture of epoxy polyester system with functional additives and a polymerization temperature of 180 °C, the adhesion level is 2.1 MPa. Reducing the polymerization temperature of a mixture of the epoxy polyester system with functional additives to 130 °C increases adhesion by 1.75 times, and the nature of the destruction passes through the polymer shell. For thermally modified wood, the level of adhesion is within 2.1 MPa, and the destruction takes place through the wood. This is due to the increased fragility of the surface after thermal modification of wood


  • Open Access

    MECHANISM STRUCTURE FORMATION OF A FOAMED FOAM LAYER UNDER THE INFLUENCE OF MINERALS

    by National University of Life and Environmental Sciences of Ukraine, Yuriy Tsapko, Ольга Бондаренко, Kyiv National University of construction and architecture, Alexey Tsapko, Alexandra Gorbachova, Sergey Mazurchuk, Юрій Цапко, Олексій Цапко, Олександра Горбачова

    The studies have established the effect of fillers on the performance of the fireproof coating, the parameters of its swelling under the influence of temperature and inhibition, which makes it possible to influence this process. The effect of fillers on the coefficient of swelling of coatings based on inorganic and organic substances during thermal exposure was investigated. It isproved that it consists in the creation of a layer on the surface of the material that prevents heating to a critical temperature and decomposition of the material. Experimental studies have confirmed that the introduction of titanium oxide and aluminum hydroxide in the amount of 5% contributes to the achievement of the highest value of the coefficient of swelling - up to 47, which is 1.11 times higher than the value of the coefficient of swelling when aluminum hydroxide is introduced, titanium oxide and talc in the amount of 3.3%, 1.12 times higher than the value of the coefficient of swelling when titanium oxide and talc in the amount of 5% were added, and 1.08 times higher than the value of the coefficient of swelling when aluminum hydroxide and talc in the amount of 5% were added. The influence of fillers under the action of high-temperature heat flow on the change in the process of swelling of the fireproof coating was established and the mechanism of the kinetics of the fillers' action, characterized by a decrease in speed and mass loss, was determined. Thus, at 700 °C, the introduction of fillers leads to theformation of refractory compositions that prevent the burnout of the resulting foam coke, which increases the efficiency of fire protection of building structures. On the basis of physicochemical research methods, it is shown that the introduction of a mixture of titanium dioxide and aluminum hydroxide in the amount of 5% each into the composition of the organic-inorganic composition leads to an increase in the coefficient of swelling, orderliness of the structure of the foam coke layer, and an increase in its heat resistance due to the dehydration of mixed titanium-aluminum phosphates.


  • Open Access

    Justification of the Wood Polymer Material Application Conditions

    by Oleksandra Horbachova, Yuriy Tsapko, Yelena Tsarenko, Serhii Mazurchuk, Ivan Kasianchuk

    The production of heat-insulating materials based on wood was analyzed in this paper. The expediency and efficiency of using wood waste were established. A study of the operational properties of the sample obtained from wood shavings polymerized with mixtures of polyester and epoxy resins was carried out. It was proven that the process’s primary regulator is the material’s density and porosity. Also, an increase in humidity and wetting reduces heat-insulating indicators. Based on thermophysical dependences, the thermal insulation properties of the samples were calculated. Moreover, it was established that the thermal conductivity does not exceed 0.21·10–6 m2/s, and the thermal conductivity of the sample – 2.85·10–3 W/(m·K). Therefore, these products can be classified as heat-insulating materials. A through-thickness compressive strength study showed that the wood shavings and polyester resin material are more fragile, and the strength limit was reduced by more than 1.2 times compared to the epoxy resin-based material. The moisture absorption results showed that a heat-insulating product made of shavings polymerized with polyester resin. Moisture absorption was 5 % after 90 days of exposure to water. On the other hand, the heat-insulating products made of shavings with epoxy resin of 4.41 % showed their resistance to moisture absorption.


  • Open Access

    Identifying parameters for wood protection against water absorption

    by Yuriy Tsapko, Ruslan Likhnyovskyi, Oleksandra Horbachova, Serhii Mazurchuk, Аleksii Tsapko, Kostiantyn Sokolenko, Andrii Matviichuk, Maryna Sukhanevych

    An issue related to using wood and timber for building structures is to ensure the stability and durability during operation within wide limits. Therefore, the object of research was the inhibition of the process of water absorption of pine and hornbeam wood during a thermal change in its structure. It is proved that in the process of thermal modification of wood, its structure changes, and, accordingly, water absorption. Namely, the maximum increase in mass under the action of water on an untreated sample of wood was more than 40 %, after thermal modification – less than 35 %. The increase in the mass of wood samples thermally modified and treated with a hydrophobic agent was less than 25 %. On the basis of the obtained results of physicochemical studies, discrepancies were found in the IR spectra of wood, both during thermal modification and with additional treatment with a hydrophobic agent, indicating structural changes in the components. In particular, the decrease or absence of the intensities of the absorption bands of some functional groups and the appearance or intensification of others. On the original hornbeam and pine thermogram, thermally modified, and thermally modified with the addition of a hydrophobic coating, thermogravimetric curves are similar to each other and are characterized by a loss of sample mass. This is possible with increasing temperature due to the processes of dehydration, destruction of hemicellulose, lignin, and cellulose with the formation of a non-combustible residue. During heat treatment of cellulose in the region of temperatures of 150÷450 °C, two processes take place in parallel. This is dehydration, accompanied by the destruction of the pyranose cycle and carbonization to form a carbon residue. Also, the process of destruction of glycosidic bonds while maintaining hydroxyl groups, accompanied by regrouping of pyranose cycles.


  • Open Access

    Establishing regularities in the application of dry pine wood

    by Yuriy Tsapko, Nataliia Buiskykh, Ruslan Likhnyovskyi, Oleksandra Horbachova, Аleksii Tsapko, Serhii Mazurchuk, Andrii Matviichuk, Maryna Sukhanevych

    The issue related to using dry wood products for building structures is to ensure their stability and durability during operation while it is necessary to take into consideration changes in their properties and structure. Therefore, the object of this study was pine wood struck by drying out. It is proved that in the process of drying, wood porosity decreases, and, accordingly, the tensile strength, depending on the degree of damage by the fungus. Specifically, with the area of damage in the range of 30‒50 %, the strength limit decreases by more than 1.3 times, and if the fungus affects the area within 80÷100 %, the wood becomes softer, more ductile while the strength limit is reduced by 1.1 times. Based on the results of physicochemical studies, discrepancies in the IR spectra were identified, indicating structural changes in the constituent components of wood. There is a decrease or absence of intensities of absorption bands of some functional groups and the appearance or intensification of others. Wood samples, in determining the highest calorific value, show a difference in values, which is explained by structural changes in wood components caused by biological processes. Thermogravimetric analysis data indicate complete burnout of dry pine wood. However, for wood with tree stands not weakened by drying, the coke residue burns out at a higher temperature. Wood with blue pigmentation affected by microorganisms has significant differences in the heating area of 400÷700 °C. The nature of coke burnout allows us to make assumptions about the different qualitative and quantitative composition of the coke residue, which is formed due to structural changes. The practical significance is the fact that the results of determining the properties and structure of dry wood make it possible to establish the operating conditions for articles and building structures


  • Open Access

    Establishing regularities of temperature conductivity reduction when protecting fabric against fire by intumescent coating

    by Yuriy Tsapko, Аleksii Tsapko, Nataliia Buiskykh, Oleksandra Horbachova, Serhii Mazurchuk, Andrii Matviichuk, Yuriy Sarapin

    This paper has analyzed materials for fire protection of textile products; it was found that there are not enough data to explain and describe the process of fire protection. Neglecting modern coatings leads to the ignition of fabric structures under the action of flame. Devising reliable methods for studying the conditions of fabric fire protection leads to the design of new types of fireproof materials. Therefore, there is a need to determine the conditions that form a barrier to high fabric temperature and to establish a mechanism for inhibiting heat transfer to the material. In this regard, the thermal conductivity process was simulated on the fabric surface using an intumescent coating, which makes it possible to estimate the coefficient of thermal conductivity at high temperatures. Based on the experimental data and theoretical dependences, the thermal conductivity coefficient of the fire-retardant layer of coked foam was calculated, which is 8.9×10-6 m2/s, due to the formation of a heat-insulating layer. The study results proved that the process of thermal insulation of textile material involves not only the decomposition of flame retardants with the formation of inert gases that interact with the flame on the sample surface but also the inhibition of heat transfer to the material treated with an intumescent coating that forms a thermally-insulating layer of coked foam on the fabric surface. The maximum possible penetration of temperature was estimated, namely generating a temperature on the sample's surface that significantly exceeds the ignition temperature of the fabric, and does not exceed 215 °C on the unheated surface. Thus, there is reason to argue about the possibility of targeted adjustment of the processes of fabric fire protection by applying coatings capable of forming a protective layer on the surface of the material, which inhibits the rate of heat transfer