KSKostiantyn Sokolenko

Kostiantyn Sokolenko

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Kostiantyn Sokolenko has a total of 23 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Establishment of the patterns of nitrogen inertization of cyclopentane vapor-air mixtures

    by Yuriy Tsapko, Oksana Berdnyk, Aleksii Tsapko, Ruslan Likhnyovskyi, Anastasiia Kovalova, Kostiantyn Sokolenko, Kostiantyn Kaveryn, Anna Borysova, Oleksandr Dotsenko

    The object of research is the process of phlegmatization of the gaseous medium of vapor-air mixtures of cyclopentane when nitrogen is introduced into this mixture. The problem of using cyclopentane for the production of thermal insulation is to ensure explosion and fire safety, since the technology for creating foamed urethane thermal insulation includes the introduction of a liquid foaming agent, such as cyclopentane, into the reaction mass. It is characterized by a low boiling point and the creation of explosive mixtures with air. In this regard, the coordinates of the points of the phlegmatization curve were experimentally determined, the value of the lower concentration limit of flame propagation was obtained, which is 1.34% vol. of cyclopentane in a mixture with air, the upper concentration limit, which is 8.64% vol., the minimum phlegmatization concentration of nitrogen, which is 48.1% vol. and the value of the combustible substance at point D (1.45% vol.) and E (6.31% vol.). Adding a phlegmatizer to the “cyclopentane – air” system gradually increases the lower branch and lowers the upper branch of the phlegmatization curve, which converge at the point of the minimum phlegmatizing nitrogen concentration. The area intersecting the phlegmatization curve is capable of flame propagation, outside of which the gas mixture is not explosive and fire-hazardous. A method for calculating the minimum safe ratio of phlegmatizer and combustible gas (steam) in technological devices based on analytical dependencies has been developed and tested. Based on the results of determining the smallest ratio of volumetric concentrations of the phlegmatizer and the combustible substance in the gas mixture, at which it is impossible to ignite it in the environment of this oxidant, the coordinates of the contact point L (45.945% vol.; 1.7445% vol.) were established, as well as the numerical value of the coefficient k (k = 26.4). The practical significance lies in the fact that the results obtained were taken into account when creating a fire-safe technology for manufacturing thermal insulation.

  • Open Access

    Determining the patterns of extinguishing polar flammable liquids with a film-forming foaming agent

    by Yuriy Tsapko, Ruslan Likhnyovskyi, Аleksii Tsapko, Vitalii Kovalenko, Oksana Slutska, Pavlo Illiuchenko, Kostiantyn Sokolenko, Yuriy Gulyk

    An issue related to the use of foaming agents to extinguish fires involving flammable liquids is to ensure the efficiency of vapor insulation of flammable liquid and the foam stability during operation. Therefore, the object of research was a change in the insulating properties of the foaming agent film when interacting with a polar combustible substance. It has been proven that the presence of foaming agent on a flammable liquid leads to the formation of an insulating film on the surface resistant to the combustion temperature of the liquid, due to which re-ignition shifts towards longer time. A film of foaming agent was formed on the surface of the flammable liquid by leaking from the screen, which led to the insulation of the surface. The measured contact area of the foaming film with the electrode was more than 6.2·10-3 m2, which indicates the formation of a barrier for temperature, which collapses over time. According to experimental data on changes in electrical resistance, the critical contact area of the foaming film with the electrode was calculated, at which the film is destroyed. Based on the derived dependences, the change in the process of mass transfer of the foaming film to a flammable liquid was calculated, equal to about 800 s. The maximum possible mass transfer of the foaming agent into the flammable liquid and the reduction of insulation capacity were evaluated. The peculiarities of foam supply to the surface of alcohol through the screen are that the quenching time was about 156 s while the critical intensity of the supply of the working solution of the foaming agent was 0.054 dm3/(m2·s). And the time interval before re-ignition was about 470 s, which is enough to cool the fire site. Thus, there is reason to assert the possibility of targeted control over the processes of extinguishing polar flammable liquids with a foaming agent


  • Open Access

    Determining patterns in the formation of a polymer shell by powder paint on wood surface

    by Yuriy Tsapko, Ruslan Likhnyovskyi, Nataliia Buiskykh, Oleksandra Horbachova, Serhii Mazurchuk, Oles Lastivka, Аleksii Tsapko, Kostiantyn Sokolenko, Andrii Matviichuk

    An issue related to using wood and wood products for building structures is to ensure their stability and durability during operation within wide limits. Therefore, the object of this study was a change in the properties of the polymer shell of powder paint on wood during thermal modification. It is proved that in the process of thermal modification of wood, its structure changes, and accordingly, during the polymerization of powder paint, degassing occurs, which affects the polymer shell. Namely, during the thermal polymerization of powder paint at a temperature of 180 °C for untreated wood, shallow bubbles and craters are characteristic of the formed polymer shell. Instead, a smooth surface is marked for a sample of thermally modified wood. Thermogravimetric analysis data show thermogravimetric curves characterized by the loss of mass of the sample of the original wood with increasing temperature due to the processes of dehydration, destruction of hemicellulose and lignin. This is dehydration, accompanied by the destruction of the pyranose cycle, and carbonization to form a carbon residue and a complex mixture of volatile products. Due to this, bubbles and craters are formed in the polymer shell of the coating. Based on the obtained results of adhesion of the polymer shell on wood, which is treated with a mixture of epoxy polyester system with functional additives and a polymerization temperature of 180 °C, the adhesion level is 2.1 MPa. Reducing the polymerization temperature of a mixture of the epoxy polyester system with functional additives to 130 °C increases adhesion by 1.75 times, and the nature of the destruction passes through the polymer shell. For thermally modified wood, the level of adhesion is within 2.1 MPa, and the destruction takes place through the wood. This is due to the increased fragility of the surface after thermal modification of wood


  • Open Access

    Identifying parameters for wood protection against water absorption

    by Yuriy Tsapko, Ruslan Likhnyovskyi, Oleksandra Horbachova, Serhii Mazurchuk, Аleksii Tsapko, Kostiantyn Sokolenko, Andrii Matviichuk, Maryna Sukhanevych

    An issue related to using wood and timber for building structures is to ensure the stability and durability during operation within wide limits. Therefore, the object of research was the inhibition of the process of water absorption of pine and hornbeam wood during a thermal change in its structure. It is proved that in the process of thermal modification of wood, its structure changes, and, accordingly, water absorption. Namely, the maximum increase in mass under the action of water on an untreated sample of wood was more than 40 %, after thermal modification – less than 35 %. The increase in the mass of wood samples thermally modified and treated with a hydrophobic agent was less than 25 %. On the basis of the obtained results of physicochemical studies, discrepancies were found in the IR spectra of wood, both during thermal modification and with additional treatment with a hydrophobic agent, indicating structural changes in the components. In particular, the decrease or absence of the intensities of the absorption bands of some functional groups and the appearance or intensification of others. On the original hornbeam and pine thermogram, thermally modified, and thermally modified with the addition of a hydrophobic coating, thermogravimetric curves are similar to each other and are characterized by a loss of sample mass. This is possible with increasing temperature due to the processes of dehydration, destruction of hemicellulose, lignin, and cellulose with the formation of a non-combustible residue. During heat treatment of cellulose in the region of temperatures of 150÷450 °C, two processes take place in parallel. This is dehydration, accompanied by the destruction of the pyranose cycle and carbonization to form a carbon residue. Also, the process of destruction of glycosidic bonds while maintaining hydroxyl groups, accompanied by regrouping of pyranose cycles.


  • Open Access

    Establishing patterns of nitrogen application for fire safety of sunflower grain storage facilities

    by Yuriy Tsapko, Kostiantyn Sokolenko, Roman Vasylyshyn, Oleksandr Melnyk, Аleksii Tsapko, Olga Bondarenko, Anatolii Karpuk

    The issue of using nitrogen to eliminate fires in granaries is related to ventilating the grain mass with nitrogen while it is necessary to take into consideration the change in gas concentration. Therefore, the object of this research was the value of the minimum concentration of nitrogen to eliminate the combustion of sunflower grain. It has been proven that in the process of thermal destruction of sunflower grain, the composition of gaseous products of thermal destruction of sunflower grain contains more than 70 % of combustible gases. Namely: carbon monoxide, over 51 %; hydrogen, about 5.7 %; and hydrocarbons with a total concentration of 13.72 %, which provide fire hazardous properties of organic material. Therefore, it should be noted that the release of the amount of combustible gases during pyrolysis requires a reduction in the amount of oxygen in the gas-air environment to eliminate fire sites. Obviously, such a mechanism for the decomposition of sunflower grain during pyrolysis is a factor in regulating the extinguishing process, due to which the amount of nitrogen to eliminate combustion increases. Comparison of experimental studies on the composition of gaseous products of thermal destruction of sunflower grain and studies to determine the minimum fire extinguishing concentration of nitrogen, at which combustion was stopped, made it possible to justify the use of nitrogen. Based on the study's results on the elimination with nitrogen of fire sites of sunflower grain, the values of the minimum fire extinguishing concentration were revealed at extinguishing, about 33.7 % by volume. At the same time, terminating the combustion of sunflower grain occurs with a decrease in the concentration of oxygen in the gas-air environment of about 14 %. The practical significance is the fact that the results obtained for determining the minimum fire extinguishing concentration of nitrogen make it possible to establish operating conditions for granaries when eliminating fire sites


  • Open Access

    Establishing regularities of wood protection against water absorption using a polymer shell

    by Yuriy Tsapko, Oleksandra Horbachova, Serhii Mazurchuk, Аleksii Tsapko, Kostiantyn Sokolenko, Andrii Matviichuk

    This paper has analyzed protective materials for timber building structures and established the need to devise reliable methods for studying the process of water absorption by the surface of the construction structure necessary for designing new types of fire-retardant materials. Therefore, it becomes necessary to determine the conditions for the formation of a barrier for water absorption and to elucidate a mechanism for inhibiting the transfer of moisture to the material. In this regard, a mathematical model of the intensity of water mass transfer when using a polymer shell made of organic material as a coating has been built, which makes it possible to assess the effectiveness of the polymer shell by the amount of water absorbed. Based on the experimental data and theoretical dependences, the intensity of absorption of water by wood was calculated; and it has been established that the protective coating reduces the amount of water absorbed by more than 20 times. The results of determining the weight gain by a sample during water exposure indicate an ambiguous impact of the nature of protection on water absorption. In particular, this implies the presence of data sufficient for the qualitative process of inhibition of moisture diffusion; and detecting, on its basis, the point in time when the drop in the coating's efficiency begins. Analysis of the results of experiments reveals that the maximum increase in mass in the case of water absorption by a non-treated sample of wood was 40 % while the increase in the mass of wood samples treated with mixtures of oil and paraffin was less than 28 %. At the same time, the best protection is shown by a mixture of oil with paraffin within 90÷95 %. Thus, there are grounds to assert the possibility of directed regulation of wood protection processes through the use of polymer coatings that can form a protective layer on the surface of the material, which inhibits the rate of absorption of water.


  • Open Access

    Determining patterns in reducing the level of bio-destruction of thermally modified timber after applying protective coatings

    by Yuriy Tsapko, Oleksandra Horbachova, Serhii Mazurchuk, Аleksii Tsapko, Kostiantyn Sokolenko, Andrii Matviichuk

    This paper reports the analysis of the biological destruction of timber and the use of protective materials, which established that the scarcity of data to explain and describe the process of bioprotection, neglect of environmentally friendly agents lead to the biodegradation of timber structures under the action of microorganisms. Devising reliable methods for studying the conditions of timber protection leads to designing new types of protective materials and application technologies. Therefore, it becomes necessary to determine the conditions for the formation of a barrier for bacteria permeability and to establish a mechanism for inhibiting material biodegradation. Given this, the dependence has been derived to determine the proportion of destroyed material under the effect of microorganisms when using an antiseptic-hydrophobicizer, which makes it possible to evaluate biopenetration. Based on the experimental data and theoretical dependences, the share of destroyed timber was determined under the effect of microorganisms, which is equal to 1 for natural timber. At the same time, this value for thermally modified timber is 0.033, and, when it is protected with oil ‒ 0.009, respectively, exposed to the action of microorganisms for 60 days. It should be noted that the presence of oil, wax, and azure leads to blocking the timber surface from penetration. Such a mechanism underlying the effect of protective coating is likely the factor in the process adjustment, due to which the integrity of the object is preserved. Thus, a polymer shell was created on the surface of the sample, significantly reducing the penetration of microorganisms inside the timber, while the loss of timber mass during biodestruction did not exceed 2.5 %. Therefore, there are grounds to assert the possibility of targeted control over the processes of timber bio-penetration by using coatings capable of forming a protective film on the surface of the material