Xu Huang
Xu Huang has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Guangquan Yue
College of Textiles, Donghua University, Shanghai, PR China
1 shared publication - Guoqiang Zu
State Grid Tianjin Electric Power Research Institute, Tianjin, China
1 shared publication Hao Huang
AECC Beijing Institute of Aeronautical Materials 100095 Beijing China
1 shared publicationHu Li
AECC Beijing Institute of Aeronautical Materials 100095 Beijing China
1 shared publication- J. Z. Liu
Beijing Institute of Aeronautical MaterialsBeijing 100095, China
1 shared publication J. Zhang
Beijing Civil Aircraft Technology Research Center of China Commercial Aircraft, Shanghai, China
1 shared publication
Latest Publications
- 15 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 999-1009
Measurement Data Complement of Power Distribution System Based on Clustering-BayesLSTM Combined Model
To address the problems of missing measurement data and low efficiency of large-scale measurement data complement in power distribution system, a measurement data complement method based on Clustering-BayesLSTM combined model is proposed. Firstly, K-mediods clustering is utilized to categorize all the quantity measurements, select the main/standby crucial measurements in each category, and calculate their average deviation from other measurements in order to effectively reduce the solution size of the long short-term memory (LSTM) neural network model. Then, through the LSTM prediction model based on Bayesian optimization, the missing main/standby crucial measurements are complemented. In addition, the average deviations from the primary/backup crucial quantity measurements are used to supplement the other missing measurements. Finally, the effectiveness of the proposed method is verified based on the real measurement data of a local power distribution system.
- 15 September 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 999-1009
Measurement Data Complement of Power Distribution System Based on Clustering-BayesLSTM Combined Model
To address the problems of missing measurement data and low efficiency of large-scale measurement data complement in power distribution system, a measurement data complement method based on Clustering-BayesLSTM combined model is proposed. Firstly, K-mediods clustering is utilized to categorize all the quantity measurements, select the main/standby crucial measurements in each category, and calculate their average deviation from other measurements in order to effectively reduce the solution size of the long short-term memory (LSTM) neural network model. Then, through the LSTM prediction model based on Bayesian optimization, the missing main/standby crucial measurements are complemented. In addition, the average deviations from the primary/backup crucial quantity measurements are used to supplement the other missing measurements. Finally, the effectiveness of the proposed method is verified based on the real measurement data of a local power distribution system.
- 9 March 2021
- Published by Wiley in Rare Metals
- Vol. 40 (12) , 3676-3684
Microstructure inheritance of matrixes of SiC f /Ti6242 composites from precursor wire coatings by α+β phase field consolidation
SiC f /Ti composite owns the attractive advantages of lightweight and excellent high‐temperature performance, which make it have great significance to the development of aerospace industry. However, the complicated fabrication route and novel architecture of SiC f /Ti composite bring about more difficulties for controlling its microstructure. In this work, the method of regulating the structure and performance of the composite matrix by adjusting the characteristics of the precursor wire was explored. The physical vapor deposition (PVD) method was applied to fabricate precursor wires. Ti6242 coatings with bamboo leaf‐shaped grains and chrysanthemum‐shaped grains were deposited on SiC fibers by changing the PVD condition. It is found that the original structure of the Ti6242 coating of precursor wire has significant impact on the microstructure of the composite matrix after hot isostatic pressing (HIP). The matrix transformed from the Ti6242 coating with bamboo leaf‐shaped grains exhibits equiaxed grain structure. While the other matrix has a columnar crystal structure, and the inside of the columnar crystal inherits the original chrysanthemum‐shaped structure. The columnar crystal matrix has lower hardness and modulus than the equiaxed grain matrix.
- 9 March 2021
- Published by Wiley in Rare Metals
- Vol. 40 (12) , 3676-3684
Microstructure inheritance of matrixes of SiC f /Ti6242 composites from precursor wire coatings by α+β phase field consolidation
SiC f /Ti composite owns the attractive advantages of lightweight and excellent high‐temperature performance, which make it have great significance to the development of aerospace industry. However, the complicated fabrication route and novel architecture of SiC f /Ti composite bring about more difficulties for controlling its microstructure. In this work, the method of regulating the structure and performance of the composite matrix by adjusting the characteristics of the precursor wire was explored. The physical vapor deposition (PVD) method was applied to fabricate precursor wires. Ti6242 coatings with bamboo leaf‐shaped grains and chrysanthemum‐shaped grains were deposited on SiC fibers by changing the PVD condition. It is found that the original structure of the Ti6242 coating of precursor wire has significant impact on the microstructure of the composite matrix after hot isostatic pressing (HIP). The matrix transformed from the Ti6242 coating with bamboo leaf‐shaped grains exhibits equiaxed grain structure. While the other matrix has a columnar crystal structure, and the inside of the columnar crystal inherits the original chrysanthemum‐shaped structure. The columnar crystal matrix has lower hardness and modulus than the equiaxed grain matrix.
- 18 November 2015
- Published by Taylor & Francis in Materials Research Innovations
- Vol. 19 (sup8) , S8-685
Crack growth and delamination behaviour in advanced Al–Li alloy laminate under constant amplitude fatigue loading
Al–Li alloy laminate, as an advanced fibre metal laminate, has not been researched in fatigue crack growth and delamination behaviour. This paper investigates the crack growth, delamination shape and size of Al–Li alloy laminate under constant amplitude fatigue loading. The results indicate that the crack growth rate of Al–Li alloy laminate is almost constant like other fibre metal laminates. More connected bridging fibres would result in slower crack growth and crack growth rate would accelerate at the high stress level. The delamination shape becomes larger and transforms from triangle to a semi-elliptical shape with crack length increasing.
- 18 November 2015
- Published by Taylor & Francis in Materials Research Innovations
- Vol. 19 (sup8) , S8-685
Crack growth and delamination behaviour in advanced Al–Li alloy laminate under constant amplitude fatigue loading
Al–Li alloy laminate, as an advanced fibre metal laminate, has not been researched in fatigue crack growth and delamination behaviour. This paper investigates the crack growth, delamination shape and size of Al–Li alloy laminate under constant amplitude fatigue loading. The results indicate that the crack growth rate of Al–Li alloy laminate is almost constant like other fibre metal laminates. More connected bridging fibres would result in slower crack growth and crack growth rate would accelerate at the high stress level. The delamination shape becomes larger and transforms from triangle to a semi-elliptical shape with crack length increasing.