Guangquan Yue
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Guangquan Yue has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
Weiping Liu
COMAC Shanghai Aircraft Manufacturing Co., Ltd., Shanghai, PR China
7 shared publications- Baozhong Sun
Shanghai Frontiers Science Center of Advanced Textiles, College of Textiles, Donghua University, Shanghai 201620, China
3 shared publications - Zhefu Li
College of Textiles, Donghua University, Shanghai, 201620, People’s Republic of China
3 shared publications - Dacheng Zhao
Composites Center of COMAC, Shanghai Aircraft Manufacturing Co., Ltd, Shanghai, P. R. China
2 shared publications - Haoxuan Zhang
Shanghai Collaborative Innovation Center of High Performance Fibers Composites (Province-Ministry Joint), Center for Civil Aviation Composites, Donghua University, Shanghai 201620, China
2 shared publications - Hongfu Li
School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China
2 shared publications
Latest Publications
- 16 November 2026
- Published by SAGE Publications in Textile Research Journal
Theoretical model and finite-element analysis of in-plane shear behavior of unidirectional prepreg
Unidirectional carbon fiber prepreg has been widely used in the manufacture of large-scale structural components in civil aircraft. However, the prediction and suppression of wrinkle defects and fiber deflection remain critical challenges that directly compromise the high-quality preforming of such components. To predict and suppress defects during preforming, this study systematically investigates the in-plane shear behavior of unidirectional carbon fiber prepreg. Based on the in-plane shear behavior of unidirectional prepreg characterized by off-axis tensile testing, the correlation between shear angle and in-plane shear force was obtained using normalization theory, and the theoretical model for its shear behavior was established with a power-law model. Finally, the theoretical model of in-plane shear behavior was embedded into the finite-element solver via “VFABRIC” user subroutine to complete the finite-element expression of in-plane shear behavior of unidirectional prepreg. The results showed that the theoretical model, which combines normalization theory with a power-law function, accurately captured the shear angle and the shear force relationship of the unidirectional prepreg, with a fitting coefficient of 0.99328. Comparison between the finite-element simulation and experimental results further validated the theoretical and finite-element models, providing a theoretical foundation and a finite element approach for the analysis of the in-plane shear behavior of prepreg under complex actual loading conditions.
- 16 November 2026
- Published by SAGE Publications in Textile Research Journal
Theoretical model and finite-element analysis of in-plane shear behavior of unidirectional prepreg
Unidirectional carbon fiber prepreg has been widely used in the manufacture of large-scale structural components in civil aircraft. However, the prediction and suppression of wrinkle defects and fiber deflection remain critical challenges that directly compromise the high-quality preforming of such components. To predict and suppress defects during preforming, this study systematically investigates the in-plane shear behavior of unidirectional carbon fiber prepreg. Based on the in-plane shear behavior of unidirectional prepreg characterized by off-axis tensile testing, the correlation between shear angle and in-plane shear force was obtained using normalization theory, and the theoretical model for its shear behavior was established with a power-law model. Finally, the theoretical model of in-plane shear behavior was embedded into the finite-element solver via “VFABRIC” user subroutine to complete the finite-element expression of in-plane shear behavior of unidirectional prepreg. The results showed that the theoretical model, which combines normalization theory with a power-law function, accurately captured the shear angle and the shear force relationship of the unidirectional prepreg, with a fitting coefficient of 0.99328. Comparison between the finite-element simulation and experimental results further validated the theoretical and finite-element models, providing a theoretical foundation and a finite element approach for the analysis of the in-plane shear behavior of prepreg under complex actual loading conditions.
- 27 May 2026
- Published by SAGE Publications in Textile Research Journal
Exploration of the crystallization shrinkage behaviors of polyphenylene sulfide for residual stress prediction
The crystallization characteristics of semicrystalline polymer matrices in thermoplastic composites significantly influence dimensional stability through additional resin shrinkage, subsequently generating residual stresses that critically affect material performance. It is necessary to analyze the influence of resin crystallization behavior on residual stress. In this paper, a novel test method for the shrinkage strain of polyphenylene sulfide resin was developed based on digital image correlation technology. The shrinkage process of polyphenylene sulfide was divided into heat loss-induced shrinkage and crystallization-induced shrinkage. It was demonstrated that the crystallization behaviors lead to the shrinkage of the resin, with the proportion of crystallization shrinkage reaching up to 86% of the whole shrinkage. The cooling rate can affect the crystallization behaviors of the resin, thereby influencing the crystallization shrinkage. The correlation between the cooling rate and the crystallinity of polyphenylene sulfide was established. In addition, the relationship between the crystallinity of polyphenylene sulfide and its overall shrinkage rate was further explored. The temperature range of crystallization shrinkage of polyphenylene sulfide was determined using the crystallization kinetic equation. The study on the crystallization shrinkage of polyphenylene sulfide provides a method for controlling the shrinkage rate of polyphenylene sulfide, and further refines the prediction of residual stress.
- 27 May 2026
- Published by SAGE Publications in Textile Research Journal
Exploration of the crystallization shrinkage behaviors of polyphenylene sulfide for residual stress prediction
The crystallization characteristics of semicrystalline polymer matrices in thermoplastic composites significantly influence dimensional stability through additional resin shrinkage, subsequently generating residual stresses that critically affect material performance. It is necessary to analyze the influence of resin crystallization behavior on residual stress. In this paper, a novel test method for the shrinkage strain of polyphenylene sulfide resin was developed based on digital image correlation technology. The shrinkage process of polyphenylene sulfide was divided into heat loss-induced shrinkage and crystallization-induced shrinkage. It was demonstrated that the crystallization behaviors lead to the shrinkage of the resin, with the proportion of crystallization shrinkage reaching up to 86% of the whole shrinkage. The cooling rate can affect the crystallization behaviors of the resin, thereby influencing the crystallization shrinkage. The correlation between the cooling rate and the crystallinity of polyphenylene sulfide was established. In addition, the relationship between the crystallinity of polyphenylene sulfide and its overall shrinkage rate was further explored. The temperature range of crystallization shrinkage of polyphenylene sulfide was determined using the crystallization kinetic equation. The study on the crystallization shrinkage of polyphenylene sulfide provides a method for controlling the shrinkage rate of polyphenylene sulfide, and further refines the prediction of residual stress.
- 27 May 2026
- Published by SAGE Publications in Textile Research Journal
Numerical simulation and influence factors of curing deformation of thermosetting resin matrix unidirectional composite stiffened panels
In the process of autoclave molding, the response and evolution of uncured skin prepreg, cured stringer, and adhesive films under the action of thermal, chemical, and mechanical fields are different. In this paper, the simulation technology of residual stress and curing deformation are employed to address the curing deformation problem of civil aircraft composite stiffener plate. The analysis of the evolution mechanism of residual stress and curing deformation of T-type stiffened panels in the co-curing, co-bonding and secondary-bonding process, as well as the co-bonding process of I-type and hat-type stiffened panels are completed. The simulation results are compared with the results through the process experiments. The simulated maximum warping deformation value and the experimental results have an error margin of no more than 10% and the deformation tendency is almost the same. An experimental test method for model parameters and a simulation and prediction model for curing deformation of composite stiffened panels are developed. An analysis is conducted on the effects of varying molding processes and stringer configurations on the deformation of stiffened panels. The findings revealed that the deformation of the secondary-bonding process is the least significant, while the deformation of the hat-type stringer stiffened panels is the most substantial. It is further determined that the resin state and the R-corner region in the prepreg would influence the deformation outcomes.
- 27 May 2026
- Published by SAGE Publications in Textile Research Journal
Numerical simulation and influence factors of curing deformation of thermosetting resin matrix unidirectional composite stiffened panels
In the process of autoclave molding, the response and evolution of uncured skin prepreg, cured stringer, and adhesive films under the action of thermal, chemical, and mechanical fields are different. In this paper, the simulation technology of residual stress and curing deformation are employed to address the curing deformation problem of civil aircraft composite stiffener plate. The analysis of the evolution mechanism of residual stress and curing deformation of T-type stiffened panels in the co-curing, co-bonding and secondary-bonding process, as well as the co-bonding process of I-type and hat-type stiffened panels are completed. The simulation results are compared with the results through the process experiments. The simulated maximum warping deformation value and the experimental results have an error margin of no more than 10% and the deformation tendency is almost the same. An experimental test method for model parameters and a simulation and prediction model for curing deformation of composite stiffened panels are developed. An analysis is conducted on the effects of varying molding processes and stringer configurations on the deformation of stiffened panels. The findings revealed that the deformation of the secondary-bonding process is the least significant, while the deformation of the hat-type stringer stiffened panels is the most substantial. It is further determined that the resin state and the R-corner region in the prepreg would influence the deformation outcomes.
- Open Access
Modeling of Preforming Process for Unidirectional Prepreg Composites Using Simplified Linear Friction Model and Fiber-Tracking Method
Hot press preforming of unidirectional prepreg composites plays a key role in the manufacturing of aerospace components. However, defect prevention remains challenging due to complex fiber reorientation and inter-ply friction phenomena that occur during the forming process. To address these challenges, this study proposes an integrated modeling approach comprising three key components: (1) a simplified linear friction model for characterization of inter-ply slip behavior, (2) a fiber-tracking algorithm that accounts for anisotropic deformation characteristics, and (3) a coupled linear shell–membrane formulation for simultaneous modeling of in-plane and out-of-plane deformation behaviors. The proposed approach is validated through comprehensive material characterization, finite element simulation, and experimental comparisons based on a 2 m Ω-stringer geometry. Simulation results align well with experiments, showing the model’s ability to predict defects. Parametric analysis also identifies temperature as a key factor in controlling interfacial friction and improving formability, with optimal results at 75 °C. This integrated modeling approach provides an effective approach for defect prediction and process optimization, contributing to reduced material waste and improved efficiency in aerospace composite manufacturing.
Open AccessModeling of Preforming Process for Unidirectional Prepreg Composites Using Simplified Linear Friction Model and Fiber-Tracking Method
Hot press preforming of unidirectional prepreg composites plays a key role in the manufacturing of aerospace components. However, defect prevention remains challenging due to complex fiber reorientation and inter-ply friction phenomena that occur during the forming process. To address these challenges, this study proposes an integrated modeling approach comprising three key components: (1) a simplified linear friction model for characterization of inter-ply slip behavior, (2) a fiber-tracking algorithm that accounts for anisotropic deformation characteristics, and (3) a coupled linear shell–membrane formulation for simultaneous modeling of in-plane and out-of-plane deformation behaviors. The proposed approach is validated through comprehensive material characterization, finite element simulation, and experimental comparisons based on a 2 m Ω-stringer geometry. Simulation results align well with experiments, showing the model’s ability to predict defects. Parametric analysis also identifies temperature as a key factor in controlling interfacial friction and improving formability, with optimal results at 75 °C. This integrated modeling approach provides an effective approach for defect prediction and process optimization, contributing to reduced material waste and improved efficiency in aerospace composite manufacturing.
- Open Access
Inter-Ply Slipping Behaviors and Kinetic Equation of Carbon Fiber-Reinforced Epoxy Prepregs for Hot Diaphragm Preforming
Wrinkles are urgent problems to be solved in the process of hot diaphragm preforming. Inter-ply slipping resistance is one of the causes of wrinkles. In this paper, based on the vertical inter-ply slipping test system, the inter-ply slipping behaviors of carbon fiber-reinforced epoxy resin composite prepregs were characterized. The mechanism of wrinkles caused by inter-ply slipping resistance was analyzed. According to the different characteristics expressed by the fiber and resin during the slip process, the inter-ply slipping behaviors of the prepregs were divided into three stages. The effect of temperature on the inter-ply slipping stresses was shown. The temperature will affect the viscosity of the prepregs. When the viscosity of the prepregs is low, the inter-ply slipping resistance will decrease. Based on the Coulomb friction law and the hydrodynamic equation, the inter-ply slipping kinetic equation of the prepregs was established. The inter-ply slipping kinetic equation was introduced into the ABAQUS main program by the ‘vfriction’ subroutine. The introduction of inter-ply slipping dynamics improved the accuracy of predicting the shape and position of wrinkles.
Open AccessInter-Ply Slipping Behaviors and Kinetic Equation of Carbon Fiber-Reinforced Epoxy Prepregs for Hot Diaphragm Preforming
Wrinkles are urgent problems to be solved in the process of hot diaphragm preforming. Inter-ply slipping resistance is one of the causes of wrinkles. In this paper, based on the vertical inter-ply slipping test system, the inter-ply slipping behaviors of carbon fiber-reinforced epoxy resin composite prepregs were characterized. The mechanism of wrinkles caused by inter-ply slipping resistance was analyzed. According to the different characteristics expressed by the fiber and resin during the slip process, the inter-ply slipping behaviors of the prepregs were divided into three stages. The effect of temperature on the inter-ply slipping stresses was shown. The temperature will affect the viscosity of the prepregs. When the viscosity of the prepregs is low, the inter-ply slipping resistance will decrease. Based on the Coulomb friction law and the hydrodynamic equation, the inter-ply slipping kinetic equation of the prepregs was established. The inter-ply slipping kinetic equation was introduced into the ABAQUS main program by the ‘vfriction’ subroutine. The introduction of inter-ply slipping dynamics improved the accuracy of predicting the shape and position of wrinkles.
- 31 May 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 58 (18) , 2079-2092
Simulation and on-line monitoring using optical fiber Bragg grating sensors of temperature history during laser-assisted automated fiber placement
Automated fiber placement (AFP) in situ consolidation (ISC) of thermoplastic composite possess the potential to reduce manufacturing costs and improve manufacturing efficiency. The properties of composite manufactured by the ISC are affected by several mechanisms including polymer degradation, crystallization, intimate contact, polymer healing and void dynamics. All these mechanisms are directly affected by the temperature history. Consequently, the control and accurate measurement of temperature history during ISC are particularly important for improving the properties of composite. In this study, a simplified three-dimensional transient heat transfer model was established. The effect of tool temperature and placement speed on the temperature history and peak temperature were predicted. Simultaneously, an online temperature monitoring system was built and the optical Fiber Bragg Grating sensors (FBGS) was used to measure the temperature history. The results indicated that the predicted results of the model were consistent with the measured results, the error was below 8%. In addition, the temperature history of layers was significantly affected by the tool temperature and placement speed. The temperature of the layers decreased to near the tool temperature after cooling, and a higher tool temperature increasing its peak temperature because of the reduce of the cooling rate. On the contrary, an increase in placement speed will reduce the peak temperature of the layers.
- 31 May 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 58 (18) , 2079-2092
Simulation and on-line monitoring using optical fiber Bragg grating sensors of temperature history during laser-assisted automated fiber placement
Automated fiber placement (AFP) in situ consolidation (ISC) of thermoplastic composite possess the potential to reduce manufacturing costs and improve manufacturing efficiency. The properties of composite manufactured by the ISC are affected by several mechanisms including polymer degradation, crystallization, intimate contact, polymer healing and void dynamics. All these mechanisms are directly affected by the temperature history. Consequently, the control and accurate measurement of temperature history during ISC are particularly important for improving the properties of composite. In this study, a simplified three-dimensional transient heat transfer model was established. The effect of tool temperature and placement speed on the temperature history and peak temperature were predicted. Simultaneously, an online temperature monitoring system was built and the optical Fiber Bragg Grating sensors (FBGS) was used to measure the temperature history. The results indicated that the predicted results of the model were consistent with the measured results, the error was below 8%. In addition, the temperature history of layers was significantly affected by the tool temperature and placement speed. The temperature of the layers decreased to near the tool temperature after cooling, and a higher tool temperature increasing its peak temperature because of the reduce of the cooling rate. On the contrary, an increase in placement speed will reduce the peak temperature of the layers.
- Open Access
- 1 May 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (5) , 055306
Determination of lubricating behavior of resin during the sliding process of unidirectional prepreg
In this paper, the lubrication behavior of resin during the molding process of unidirectional prepreg materials was scrutinized using a custom-made device. The thickness of the resin between prepregs under various conditions was calculated using Inverse Hydrodynamic Lubrication (IHL) theory to elucidate the lubrication mechanism. This calculation was confirmed by examining the surface morphologies of the prepreg and employing Digital Image Correlation (DIC) techniques for validation. Furthermore, the effect of unidirectional fiber orientation on the process of inter-ply sliding was quantitatively analyzed through the combined roughness. The study showed that factors such as sliding velocity, normal pressure, and fiber orientation play a key role in the lubrication mechanism. The lubrication behavior of unidirectional prepreg transformed to mixed lubrication under specific conditions. The results in our study of the lubrication mechanism have significant implications for the refinement of molding process and the enhancement of numerical simulations of unidirectional prepregs.
- 1 May 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (5) , 055306
Open AccessDetermination of lubricating behavior of resin during the sliding process of unidirectional prepreg
In this paper, the lubrication behavior of resin during the molding process of unidirectional prepreg materials was scrutinized using a custom-made device. The thickness of the resin between prepregs under various conditions was calculated using Inverse Hydrodynamic Lubrication (IHL) theory to elucidate the lubrication mechanism. This calculation was confirmed by examining the surface morphologies of the prepreg and employing Digital Image Correlation (DIC) techniques for validation. Furthermore, the effect of unidirectional fiber orientation on the process of inter-ply sliding was quantitatively analyzed through the combined roughness. The study showed that factors such as sliding velocity, normal pressure, and fiber orientation play a key role in the lubrication mechanism. The lubrication behavior of unidirectional prepreg transformed to mixed lubrication under specific conditions. The results in our study of the lubrication mechanism have significant implications for the refinement of molding process and the enhancement of numerical simulations of unidirectional prepregs.
- Open Access
- 5 April 2024
- Published by MDPI AG in Journal of Composites Science
- Vol. 8 (4) , 133
Determination of the In-Plane Shear Behavior of and Process Influence on Uncured Unidirectional CF/Epoxy Prepreg Using Digital Image Correlation Analysis
The investigation of the in-plane shear behavior of prepreg is crucial for understanding the generation of wrinkles of preforms in advanced composite manufacturing processes, such as automated fiber placement and thermoforming. Despite this significance, there is currently no standardized test method for characterizing uncured unidirectional (UD) prepreg. This paper introduces a ±45° off-axis tensile test designed to assess the in-plane shear behavior of UD carbon fiber-reinforced epoxy prepreg (CF/epoxy). Digital image correlation (DIC) was employed to quantitatively track the strains in three dimensions and the shear angle evolution during the stretching process. The influences of the temperature and stretching rate on the in-plane shear behavior of the prepreg were further investigated. The results reveal that four shear characteristic zones and wrinkling behaviors are clearly distinguished. The actual in-plane shear angle is significantly lower than the theoretical value due to fiber constraints from both the in-plane and out-of-plane aspects. When the off-axis tensile displacement (d) is less than 15.6 mm, the ±45° specimens primarily exhibit macroscale in-plane shear behavior, induced by interlaminar interface shear between the +45° ply and −45° ply at the mesoscale. The shear angle increases linearly with the d. However, when d > 15.6 mm, fiber squeezing and wrinkling begin to occur. When d > 29 mm, the in-plane shear disappears in the completely sheared zone (A). The reduction in the resin viscosity of the CF/epoxy prepreg caused by increased temperature is identified as the primary factor in lowering the in-plane shear force resistance, followed by the effect of the increasing resin curing degree. Higher shear rates can lead to a substantial increase in shear forces, eventually causing cracking failure in the prepreg. The findings demonstrate the feasibility of the test method for predicting and extracting uncured prepreg in-plane shear behaviors and the strain-rate and temperature dependency of the material response.
- 5 April 2024
- Published by MDPI AG in Journal of Composites Science
- Vol. 8 (4) , 133
Open AccessDetermination of the In-Plane Shear Behavior of and Process Influence on Uncured Unidirectional CF/Epoxy Prepreg Using Digital Image Correlation Analysis
The investigation of the in-plane shear behavior of prepreg is crucial for understanding the generation of wrinkles of preforms in advanced composite manufacturing processes, such as automated fiber placement and thermoforming. Despite this significance, there is currently no standardized test method for characterizing uncured unidirectional (UD) prepreg. This paper introduces a ±45° off-axis tensile test designed to assess the in-plane shear behavior of UD carbon fiber-reinforced epoxy prepreg (CF/epoxy). Digital image correlation (DIC) was employed to quantitatively track the strains in three dimensions and the shear angle evolution during the stretching process. The influences of the temperature and stretching rate on the in-plane shear behavior of the prepreg were further investigated. The results reveal that four shear characteristic zones and wrinkling behaviors are clearly distinguished. The actual in-plane shear angle is significantly lower than the theoretical value due to fiber constraints from both the in-plane and out-of-plane aspects. When the off-axis tensile displacement (d) is less than 15.6 mm, the ±45° specimens primarily exhibit macroscale in-plane shear behavior, induced by interlaminar interface shear between the +45° ply and −45° ply at the mesoscale. The shear angle increases linearly with the d. However, when d > 15.6 mm, fiber squeezing and wrinkling begin to occur. When d > 29 mm, the in-plane shear disappears in the completely sheared zone (A). The reduction in the resin viscosity of the CF/epoxy prepreg caused by increased temperature is identified as the primary factor in lowering the in-plane shear force resistance, followed by the effect of the increasing resin curing degree. Higher shear rates can lead to a substantial increase in shear forces, eventually causing cracking failure in the prepreg. The findings demonstrate the feasibility of the test method for predicting and extracting uncured prepreg in-plane shear behaviors and the strain-rate and temperature dependency of the material response.
- Open Access
- 1 March 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (3) , 035308
Characterizing the stress relaxation behavior of unidirectional prepreg through a parallel fractional-order viscoelastic model
In the hot-stamp molding and hot diaphragm forming processes of composites, pressure significantly influences shaping quality. This study establishes a novel parallel fractional-order viscoelastic (PFOV) model with two Scott-Blair elements, achieving remarkable accuracy (R2 = 0.99) with fewer parameters. Unlike traditional models, it incorporates the force history of prepreg, providing a more precise representation of its mechanical response. Comparative analysis against established models underscores its superior ability to capture intricate stress relaxation behaviors. Notably, the model’s reduced parameters enhance its physical interpretability, offering a significant advantage in simulating and predicting prepreg material compression behavior for diverse manufacturing processes.
- 1 March 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (3) , 035308
Open AccessCharacterizing the stress relaxation behavior of unidirectional prepreg through a parallel fractional-order viscoelastic model
In the hot-stamp molding and hot diaphragm forming processes of composites, pressure significantly influences shaping quality. This study establishes a novel parallel fractional-order viscoelastic (PFOV) model with two Scott-Blair elements, achieving remarkable accuracy (R2 = 0.99) with fewer parameters. Unlike traditional models, it incorporates the force history of prepreg, providing a more precise representation of its mechanical response. Comparative analysis against established models underscores its superior ability to capture intricate stress relaxation behaviors. Notably, the model’s reduced parameters enhance its physical interpretability, offering a significant advantage in simulating and predicting prepreg material compression behavior for diverse manufacturing processes.
- Open Access
- 1 January 2024
- Published by SAGE Publications in Journal of Engineered Fibers and Fabrics
- Vol. 19
Processing and characterization of high-performance thermoplastic composites manufactured by laser-assisted automated fiber placement in-situ consolidation and hot-press
Due to the short dwell time of processing temperature and pressure, the quality of the composite manufactured by AFP was not equal to the traditional processing method like autoclave or hot-press. Deeply understanding the mechanism of differences was conducive to improving the performance of the composite manufactured by AFP. In this study, the properties of high-performance carbon fiber reinforced polyphenylene sulfide (CF/PPS) thermoplastic composites manufactured by laser-assisted automated fiber placement (LAFP) in-situ consolidation and hot-press was characterized and compared. The temperature history of LAFP in situ consolidation indicated that the heating and cooling process occurred during a few seconds. And the crystallinity was only 21.6% for the laminate from LATP, while the void content was 2.75%. Due to the low crystallinity, high void content and low interlaminar bonding, the ILSS of the laminate from LAFP in situ consolidation was 34.9% lower than that of hot-press. However, the mode Ⅰ fracture toughness was 103.7% higher than hot-press.
- 1 January 2024
- Published by SAGE Publications in Journal of Engineered Fibers and Fabrics
- Vol. 19
Open AccessProcessing and characterization of high-performance thermoplastic composites manufactured by laser-assisted automated fiber placement in-situ consolidation and hot-press
Due to the short dwell time of processing temperature and pressure, the quality of the composite manufactured by AFP was not equal to the traditional processing method like autoclave or hot-press. Deeply understanding the mechanism of differences was conducive to improving the performance of the composite manufactured by AFP. In this study, the properties of high-performance carbon fiber reinforced polyphenylene sulfide (CF/PPS) thermoplastic composites manufactured by laser-assisted automated fiber placement (LAFP) in-situ consolidation and hot-press was characterized and compared. The temperature history of LAFP in situ consolidation indicated that the heating and cooling process occurred during a few seconds. And the crystallinity was only 21.6% for the laminate from LATP, while the void content was 2.75%. Due to the low crystallinity, high void content and low interlaminar bonding, the ILSS of the laminate from LAFP in situ consolidation was 34.9% lower than that of hot-press. However, the mode Ⅰ fracture toughness was 103.7% higher than hot-press.