Yong Chan Jung
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Yong Chan Jung has a total of 113 co-authors. Here are the top co-authors by number of shared publications:
- Jiyoung Kim
The University of Texas at Dallas
16 shared publications - Si Joon Kim
Kangwon National University
12 shared publications In-Sung Park
10 shared publications- Jinho Ahn
Hanyang University, Division of Materials Science and Engineering, Seoul, Republic of Korea
10 shared publications - Harrison Sejoon Kim
Department of Materials Science and Engineering, The University of Texas at Dallas 3 , 800 West Campbell Road, Richardson, Texas 75080, USA
9 shared publications Jinho Ahn
9 shared publications
Latest Publications
- 1 March 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (10)
Thermal budget study to simultaneously achieve low-temperature (<400 °C) process and high endurance of ferroelectric Hf0.5Zr0.5O2 thin films
This work comprehensively investigates the thermal budget required to simultaneously achieve low-temperature process conditions and high endurance in atomic layer deposited ferroelectric Hf0.5Zr0.5O2 (HZO) thin films. Because a certain level of thermal budget is required to achieve ferroelectricity in 10 nm HZO thin films, the crystallization temperature can be lowered below 400 °C by simply increasing the annealing time. In addition, the analysis of the crystallization behavior of HZO thin films based on the Johnson–Mehl–Avrami–Kolmogorov model revealed that longer annealing times are required to lower the annealing temperature for HZO crystallization due to the limitation of the crystallization rate. Consequently, low-temperature (<400 °C) ferroelectric HZO thin films with large remanent polarization along with improved leakage behavior and endurance were realized. These results not only facilitate the back-end-of-line integration of HZO thin films but also demonstrate the feasibility of in situ HZO crystallization by thermal budget for subsequent interconnect formation, simplifying the overall process and saving costs by eliminating a dedicated annealing process.
- 1 March 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (10)
Thermal budget study to simultaneously achieve low-temperature (<400 °C) process and high endurance of ferroelectric Hf0.5Zr0.5O2 thin films
This work comprehensively investigates the thermal budget required to simultaneously achieve low-temperature process conditions and high endurance in atomic layer deposited ferroelectric Hf0.5Zr0.5O2 (HZO) thin films. Because a certain level of thermal budget is required to achieve ferroelectricity in 10 nm HZO thin films, the crystallization temperature can be lowered below 400 °C by simply increasing the annealing time. In addition, the analysis of the crystallization behavior of HZO thin films based on the Johnson–Mehl–Avrami–Kolmogorov model revealed that longer annealing times are required to lower the annealing temperature for HZO crystallization due to the limitation of the crystallization rate. Consequently, low-temperature (<400 °C) ferroelectric HZO thin films with large remanent polarization along with improved leakage behavior and endurance were realized. These results not only facilitate the back-end-of-line integration of HZO thin films but also demonstrate the feasibility of in situ HZO crystallization by thermal budget for subsequent interconnect formation, simplifying the overall process and saving costs by eliminating a dedicated annealing process.
- 23 January 2025
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 25 (5) , 1831-1837
Cross-Point Ferroelectric Hf0.5Zr0.5O2 Capacitors for Remanent Polarization-Driven In-Memory Computing
Ferroelectric Hf0.5Zr0.5O2 (HZO) capacitors have been extensively explored for in-memory computing (IMC) applications due to their nonvolatility and back-end-of-line (BEOL) compatible process. Several IMC approaches using resistance and capacitance states in ferroelectric HZO have been proposed for vector-matrix multiplication (VMM), but previous approaches suffer from limited accuracy and reliability. In this work, we propose a promising approach centered on the remanent polarization (P-r) switching of binary ferroelectric HZO capacitor synapses. We experimentally demonstrate a simple pattern recognition task showing that the voltage readout of P-r switching provides excellent accuracy due to its high on/off ratio and consequent reliability. We also performed large-scale simulations on a complex inference task, achieving high accuracy and immunity to device variations. We therefore believe that our proposed paradigm is promising for near-term neuromorphic IMC.
- 23 January 2025
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 25 (5) , 1831-1837
Cross-Point Ferroelectric Hf0.5Zr0.5O2 Capacitors for Remanent Polarization-Driven In-Memory Computing
Ferroelectric Hf0.5Zr0.5O2 (HZO) capacitors have been extensively explored for in-memory computing (IMC) applications due to their nonvolatility and back-end-of-line (BEOL) compatible process. Several IMC approaches using resistance and capacitance states in ferroelectric HZO have been proposed for vector-matrix multiplication (VMM), but previous approaches suffer from limited accuracy and reliability. In this work, we propose a promising approach centered on the remanent polarization (P-r) switching of binary ferroelectric HZO capacitor synapses. We experimentally demonstrate a simple pattern recognition task showing that the voltage readout of P-r switching provides excellent accuracy due to its high on/off ratio and consequent reliability. We also performed large-scale simulations on a complex inference task, achieving high accuracy and immunity to device variations. We therefore believe that our proposed paradigm is promising for near-term neuromorphic IMC.
- 7 September 2023
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 5 (9) , 4726-4745
Toward Low-Thermal-Budget Hafnia-Based Ferroelectrics via Atomic Layer Deposition
- 7 September 2023
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 5 (9) , 4726-4745
Toward Low-Thermal-Budget Hafnia-Based Ferroelectrics via Atomic Layer Deposition
- 28 November 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 121 (22) , 222901
Robust low-temperature (350 °C) ferroelectric Hf0.5Zr0.5O2 fabricated using anhydrous H2O2 as the ALD oxidant
In this Letter, the robust ferroelectric properties of low-temperature (350 °C) Hf0.5Zr0.5O2 (HZO) films are investigated. We demonstrate that the lower crystallization temperature of HZO films originates from a densified film deposition with an anhydrous H2O2 oxidant in the atomic layer deposition process. As a consequence of this densification, H2O2-based HZO films showed completely crystallinity with fewer defects at a lower annealing temperature of 350 °C. This reduction in the crystallization temperature additionally suppresses the oxidation of TiN electrodes, thereby improving device reliability. The low-temperature crystallization process produces an H2O2-based HZO capacitor with a high remanent polarization (Pr), reduced leakage current, high breakdown voltage, and better endurance. Furthermore, while an O3-based HZO capacitor requires wake-up cycling to achieve stable Pr, the H2O2-based HZO capacitor demonstrates a significantly reduced wake-up nature. Anhydrous H2O2 oxidant enables the fabrication of a more reliable ferroelectric HZO device using a low process thermal budget (350 °C).
- 28 November 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 121 (22) , 222901
Robust low-temperature (350 °C) ferroelectric Hf0.5Zr0.5O2 fabricated using anhydrous H2O2 as the ALD oxidant
In this Letter, the robust ferroelectric properties of low-temperature (350 °C) Hf0.5Zr0.5O2 (HZO) films are investigated. We demonstrate that the lower crystallization temperature of HZO films originates from a densified film deposition with an anhydrous H2O2 oxidant in the atomic layer deposition process. As a consequence of this densification, H2O2-based HZO films showed completely crystallinity with fewer defects at a lower annealing temperature of 350 °C. This reduction in the crystallization temperature additionally suppresses the oxidation of TiN electrodes, thereby improving device reliability. The low-temperature crystallization process produces an H2O2-based HZO capacitor with a high remanent polarization (Pr), reduced leakage current, high breakdown voltage, and better endurance. Furthermore, while an O3-based HZO capacitor requires wake-up cycling to achieve stable Pr, the H2O2-based HZO capacitor demonstrates a significantly reduced wake-up nature. Anhydrous H2O2 oxidant enables the fabrication of a more reliable ferroelectric HZO device using a low process thermal budget (350 °C).
- 14 February 2022
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 4 (4) , 1405-1414
Relaxation Induced by Imprint Phenomena in Low-Temperature (400 °C) Processed Hf0.5Zr0.5O2-Based Metal-Ferroelectric-Metal Capacitors
- 14 February 2022
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 4 (4) , 1405-1414
Relaxation Induced by Imprint Phenomena in Low-Temperature (400 °C) Processed Hf0.5Zr0.5O2-Based Metal-Ferroelectric-Metal Capacitors
- 11 February 2022
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 40 (2) , 022406
High wet-etch resistance SiO2 films deposited by plasma-enhanced atomic layer deposition with 1,1,1-tris(dimethylamino)disilane
A novel precursor, 1,1,1-tris(dimethylamino)disilane {TADS, [(H3C)2N]3Si2H3}, is used to deposit silicon dioxide (SiO2) films in a temperature range of 115–480 °C by thermal atomic layer deposition (tALD) and plasma-enhanced atomic layer deposition (PEALD) techniques. Compared to tris(dimethylamino)silane (TDMAS), the additional Si-Si bond in TADS is expected to enhance the reactivity of the molecule due to the polarization of the bond. In the tALD process, TADS gives a growth rate of 0.06 nm/cycle, which is approximately 20% higher than that of TDMAS, and an excellent conformality (>95% step coverage) in high aspect ratio nanotrenches (6:1). In the case of the PEALD process, TADS leads to not only a higher or at least comparable growth rates (0.11 nm/cycle), but also a higher bulk film density (∼2.38 g/cm3). As a result, the PEALD SiO2 films of TADS show a wet-etch rate down to 1.6 nm/min in 200:1 HF, which is comparable to that of the thermal oxide. Analyzed with Fourier-Transform Infrared (FTIR), the SiO2 films contain predominant Si−O bonds and a low level of Si−H and O−H bonds, consistent with the observed high wet-etch resistance. Furthermore, the PEALD SiO2 films deposited at 310 °C have at least 75% step coverage in high aspect ratio nanotrenches, suggesting that TADS is applicable for forming high-quality SiO2 films on both planar and patterned surfaces.
- 11 February 2022
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 40 (2) , 022406
High wet-etch resistance SiO2 films deposited by plasma-enhanced atomic layer deposition with 1,1,1-tris(dimethylamino)disilane
A novel precursor, 1,1,1-tris(dimethylamino)disilane {TADS, [(H3C)2N]3Si2H3}, is used to deposit silicon dioxide (SiO2) films in a temperature range of 115–480 °C by thermal atomic layer deposition (tALD) and plasma-enhanced atomic layer deposition (PEALD) techniques. Compared to tris(dimethylamino)silane (TDMAS), the additional Si-Si bond in TADS is expected to enhance the reactivity of the molecule due to the polarization of the bond. In the tALD process, TADS gives a growth rate of 0.06 nm/cycle, which is approximately 20% higher than that of TDMAS, and an excellent conformality (>95% step coverage) in high aspect ratio nanotrenches (6:1). In the case of the PEALD process, TADS leads to not only a higher or at least comparable growth rates (0.11 nm/cycle), but also a higher bulk film density (∼2.38 g/cm3). As a result, the PEALD SiO2 films of TADS show a wet-etch rate down to 1.6 nm/min in 200:1 HF, which is comparable to that of the thermal oxide. Analyzed with Fourier-Transform Infrared (FTIR), the SiO2 films contain predominant Si−O bonds and a low level of Si−H and O−H bonds, consistent with the observed high wet-etch resistance. Furthermore, the PEALD SiO2 films deposited at 310 °C have at least 75% step coverage in high aspect ratio nanotrenches, suggesting that TADS is applicable for forming high-quality SiO2 films on both planar and patterned surfaces.
- 13 December 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (24) , 242901
Low-thermal-budget (300 °C) ferroelectric TiN/Hf0.5Zr0.5O2/TiN capacitors realized using high-pressure annealing
In this Letter, a high-pressure annealing (HPA) process is proposed as a way to reduce the thermal budget of Hf0.5Zr0.5O2 (HZO) thin films with ferroelectric behaviors. The low-thermal-budget process is essential for integrating ferroelectric devices in the back-end-of-line to provide more functionalities and effective memory area. For the HZO film annealed at 300 °C using the HPA process, an orthorhombic phase responsible for ferroelectric behavior was formed with a decrease in film thickness, resulting in a remanent polarization (Pr) of ∼13 μC/cm2 (i.e., 2Pr of ∼26 μC/cm2). Meanwhile, when only the annealing time was increased at 300 °C without applying pressure, the HZO film did not crystallize and exhibited linear dielectric properties. Consequently, the HZO films (<10 nm) can be crystallized by applying pressure (15 atm) even at low temperatures of 300 °C, thereby obtaining ferroelectric properties.
- 13 December 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (24) , 242901
Low-thermal-budget (300 °C) ferroelectric TiN/Hf0.5Zr0.5O2/TiN capacitors realized using high-pressure annealing
In this Letter, a high-pressure annealing (HPA) process is proposed as a way to reduce the thermal budget of Hf0.5Zr0.5O2 (HZO) thin films with ferroelectric behaviors. The low-thermal-budget process is essential for integrating ferroelectric devices in the back-end-of-line to provide more functionalities and effective memory area. For the HZO film annealed at 300 °C using the HPA process, an orthorhombic phase responsible for ferroelectric behavior was formed with a decrease in film thickness, resulting in a remanent polarization (Pr) of ∼13 μC/cm2 (i.e., 2Pr of ∼26 μC/cm2). Meanwhile, when only the annealing time was increased at 300 °C without applying pressure, the HZO film did not crystallize and exhibited linear dielectric properties. Consequently, the HZO films (<10 nm) can be crystallized by applying pressure (15 atm) even at low temperatures of 300 °C, thereby obtaining ferroelectric properties.
- Open Access
Microstructures of HfOx Films Prepared via Atomic Layer Deposition Using La(NO3)3·6H2O Oxidants
Hafnium oxide (HfOx) films have a wide range of applications in solid-state devices, including metal–oxide–semiconductor field-effect transistors (MOSFETs). The growth of HfOx films from the metal precursor tetrakis(ethylmethylamino) hafnium with La(NO3)3·6H2O solution (LNS) as an oxidant was investigated. The atomic layer deposition (ALD) conditions were optimized, and the chemical state, surface morphology, and microstructure of the prepared films were characterized. Furthermore, to better understand the effects of LNS on the deposition process, HfOx films deposited using a conventional oxidant (H2O) were also prepared. The ALD process using LNS was observed to be self-limiting, with an ALD temperature window of 200–350 °C and a growth rate of 1.6 Å per cycle, two times faster than that with H2O. HfOx films deposited using the LNS oxidant had smaller crystallites than those deposited using H2O, as well as more suboxides or defects because of the higher number of grain boundaries. In addition, there was a difference in the preferred orientations of the HfOx films deposited using LNS and H2O, and consequently, a difference in surface energy. Finally, a film growth model based on the surface energy difference was proposed to explain the observed growth rate and crystallite size trends.
Open AccessMicrostructures of HfOx Films Prepared via Atomic Layer Deposition Using La(NO3)3·6H2O Oxidants
Hafnium oxide (HfOx) films have a wide range of applications in solid-state devices, including metal–oxide–semiconductor field-effect transistors (MOSFETs). The growth of HfOx films from the metal precursor tetrakis(ethylmethylamino) hafnium with La(NO3)3·6H2O solution (LNS) as an oxidant was investigated. The atomic layer deposition (ALD) conditions were optimized, and the chemical state, surface morphology, and microstructure of the prepared films were characterized. Furthermore, to better understand the effects of LNS on the deposition process, HfOx films deposited using a conventional oxidant (H2O) were also prepared. The ALD process using LNS was observed to be self-limiting, with an ALD temperature window of 200–350 °C and a growth rate of 1.6 Å per cycle, two times faster than that with H2O. HfOx films deposited using the LNS oxidant had smaller crystallites than those deposited using H2O, as well as more suboxides or defects because of the higher number of grain boundaries. In addition, there was a difference in the preferred orientations of the HfOx films deposited using LNS and H2O, and consequently, a difference in surface energy. Finally, a film growth model based on the surface energy difference was proposed to explain the observed growth rate and crystallite size trends.
- 25 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (1) , 21-24
Highly Reliable Selection Behavior With Controlled Ag Doping of Nano-Polycrystalline ZnO Layer for 3D X-Point Framework
In this letter, a threshold switching (TS) selector with Ag doping-based nano-polycrystalline ZnO switching layer (SL) having (002) preferred orientation has been manifested, without incorporating an active Ag metal layer, using a facile co-sputtering deposition technique. The TS selectors with extremely controlled doping of ~0.14 at. % Ag concentration showed remarkable electroforming (EF)-free selection behavior such as gigantic selectivity (~10 11 ), extreme-low off -current (~10 fA), high on -current density (~1.6 MA/cm 2 ), ultra-steep switching slope (~0.8 mV/decade), satisfactory endurance (>10 6 ), fast switch- on speed (~38 ns) and relaxation speed (~64 ns), and high device yield (~90%). Furthermore, selector devices showed reproducible selection behavior with stable threshold voltage (V th ) having merely ~8% variances.
- 25 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (1) , 21-24
Highly Reliable Selection Behavior With Controlled Ag Doping of Nano-Polycrystalline ZnO Layer for 3D X-Point Framework
In this letter, a threshold switching (TS) selector with Ag doping-based nano-polycrystalline ZnO switching layer (SL) having (002) preferred orientation has been manifested, without incorporating an active Ag metal layer, using a facile co-sputtering deposition technique. The TS selectors with extremely controlled doping of ~0.14 at. % Ag concentration showed remarkable electroforming (EF)-free selection behavior such as gigantic selectivity (~10 11 ), extreme-low off -current (~10 fA), high on -current density (~1.6 MA/cm 2 ), ultra-steep switching slope (~0.8 mV/decade), satisfactory endurance (>10 6 ), fast switch- on speed (~38 ns) and relaxation speed (~64 ns), and high device yield (~90%). Furthermore, selector devices showed reproducible selection behavior with stable threshold voltage (V th ) having merely ~8% variances.
- Open Access
- 1 November 2021
- Published by AIP Publishing in AIP Advances
- Vol. 11 (11) , 115213
Nano-polycrystalline Ag-doped ZnO layer for steep-slope threshold switching selectors
In this work, a nano-polycrystalline Ag-doped ZnO-based threshold switching (TS) selector via a facile co-sputtering technique is investigated without using an Ag active metal layer. The effects of the Ag concentration with respect to OFF-state leakage current (Ioff) were studied, and the results demonstrate that by regulating the Ag doping concentration in the switching layer (SL), an electroforming-free switching with an Ion/Ioff ratio of ∼108 could be achieved, having an extremely low Ioff value of ∼10−13 A. Furthermore, cycling endurance can also be improved as the formation of a laterally thick and stable filament does not happen promptly with consequent measurements when there is a limited amount of Ag in the SL. The selector device performance enhancement is attributed to the doping-based polycrystalline structure that facilitates enhanced control on filament formation due to the restricted availability and anisotropic diffusion of Ag ions in the polycrystalline ZnO SL, thereby trimming down the overall stochasticity during metallic filament growth. The present study demonstrates that a doping-based polycrystalline SL structure can be implemented in a selector device to augment TS characteristics, i.e., device variances and cycling endurance for adoption in ultra-high density memory applications.
- 1 November 2021
- Published by AIP Publishing in AIP Advances
- Vol. 11 (11) , 115213
Open AccessNano-polycrystalline Ag-doped ZnO layer for steep-slope threshold switching selectors
In this work, a nano-polycrystalline Ag-doped ZnO-based threshold switching (TS) selector via a facile co-sputtering technique is investigated without using an Ag active metal layer. The effects of the Ag concentration with respect to OFF-state leakage current (Ioff) were studied, and the results demonstrate that by regulating the Ag doping concentration in the switching layer (SL), an electroforming-free switching with an Ion/Ioff ratio of ∼108 could be achieved, having an extremely low Ioff value of ∼10−13 A. Furthermore, cycling endurance can also be improved as the formation of a laterally thick and stable filament does not happen promptly with consequent measurements when there is a limited amount of Ag in the SL. The selector device performance enhancement is attributed to the doping-based polycrystalline structure that facilitates enhanced control on filament formation due to the restricted availability and anisotropic diffusion of Ag ions in the polycrystalline ZnO SL, thereby trimming down the overall stochasticity during metallic filament growth. The present study demonstrates that a doping-based polycrystalline SL structure can be implemented in a selector device to augment TS characteristics, i.e., device variances and cycling endurance for adoption in ultra-high density memory applications.