Dragan Adamovic
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dragan Adamovic has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Fatima Zivic
Faculty of Engineering, University of Kragujevac, Sestre Janjić 6, 34000 Kragujevac, Serbia
8 shared publications - Dušan Arsić
Faculty of Engineering, University of Kragujevac, Sestre Janjić 6, 34000 Kragujevac, Serbia
5 shared publications - Djordje Ivković
Faculty of Engineering, University of Kragujevac, 34000 Kragujevac, Serbia
4 shared publications - Marko Delić
Faculty of Engineering, University of Kragujevac, 34000 Kragujevac, Serbia
4 shared publications - Vesna Mandić
Faculty of Engineering, University of Kragujevac, 34000 Kragujevac, Serbia
4 shared publications Nenad Grujovic
University of Kragujevac
3 shared publications
Latest Publications
- 25 February 2026
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 337
A new artificial neural network model for prediction of fatigue strength and yield strength of various steel grades
- 25 February 2026
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 337
A new artificial neural network model for prediction of fatigue strength and yield strength of various steel grades
- Open Access
- 11 January 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (1) , 30
An Experimental–Numerical Framework for Springback Prediction and Angle Compensation in Air Bending with Additively Manufactured Polymer Tools
Additive manufacturing of polymer tools represents a promising alternative to conventional steel tooling for low-force and low-volume sheet metal air bending. However, accurate prediction of sheet springback and the resulting deviation of the bending angle after elastic unloading remains a major challenge. This study presents an integrated experimental–numerical framework for the analysis of air bending with additively manufactured polymer tools, with emphasis on material characterization, springback prediction, and tool angle compensation. The methodology combines uniaxial tensile testing, controlled air-bending experiments, finite element modelling with rigid and deformable tools, and optical 3D scanning for angle measurement. Low-carbon steel DC04 sheets were modeled using an elastoplastic constitutive law, while additively manufactured ABS tools were described by experimentally calibrated material models. Numerical simulations were performed over a range of forming forces to evaluate springback behavior and elastic tool deformation. The results show very good agreement between experiments and simulations. Deviations in bending angle were below 1.5% for metallic tools and below 0.5% for springback compensation, with the smallest discrepancy obtained using a two-dimensional model with deformable tools. Experimental validation with ABS tools confirmed bending accuracy within ±1°. The proposed framework provides a reliable basis for springback prediction and rational design of additively manufactured polymer tools for air-bending applications.
- 11 January 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (1) , 30
Open AccessAn Experimental–Numerical Framework for Springback Prediction and Angle Compensation in Air Bending with Additively Manufactured Polymer Tools
Additive manufacturing of polymer tools represents a promising alternative to conventional steel tooling for low-force and low-volume sheet metal air bending. However, accurate prediction of sheet springback and the resulting deviation of the bending angle after elastic unloading remains a major challenge. This study presents an integrated experimental–numerical framework for the analysis of air bending with additively manufactured polymer tools, with emphasis on material characterization, springback prediction, and tool angle compensation. The methodology combines uniaxial tensile testing, controlled air-bending experiments, finite element modelling with rigid and deformable tools, and optical 3D scanning for angle measurement. Low-carbon steel DC04 sheets were modeled using an elastoplastic constitutive law, while additively manufactured ABS tools were described by experimentally calibrated material models. Numerical simulations were performed over a range of forming forces to evaluate springback behavior and elastic tool deformation. The results show very good agreement between experiments and simulations. Deviations in bending angle were below 1.5% for metallic tools and below 0.5% for springback compensation, with the smallest discrepancy obtained using a two-dimensional model with deformable tools. Experimental validation with ABS tools confirmed bending accuracy within ±1°. The proposed framework provides a reliable basis for springback prediction and rational design of additively manufactured polymer tools for air-bending applications.
- Open Access
- 23 December 2025
- Published by MDPI AG in Preprints.org
An Experimental–Numerical Framework for Springback Prediction and Angle Compensation in Air Bending with Additively Manufactured Polymer Tools
Additive manufacturing of polymer tools represents a promising alternative to conventional steel tooling for low-force and low-volume sheet metal air bending. However, accurate prediction of sheet springback and the resulting deviation of the bending angle after elastic unloading remains a major challenge. This study presents an integrated experimental–numerical framework for the analysis of air bending with additively manufactured polymer tools, with emphasis on material characterization, springback prediction, and tool angle compensation. The methodology combines uniaxial tensile testing, controlled air-bending experiments, finite element modelling with rigid and deformable tools, and optical 3D scanning for angle measurement. Low-carbon steel DC04 sheets were modeled using an elastoplastic constitutive law, while FDM-printed ABS tools were described by experimentally calibrated material models. Numerical simulations were performed over a range of forming forces to evaluate springback behavior and elastic tool deformation. The results show very good agreement between experiments and simulations. Deviations in bending angle were below 1.5% for metallic tools and below 0.5% for springback compensation, with the smallest discrepancy obtained using a two-dimensional model with deformable tools. Experimental validation with ABS tools confirmed bending accuracy within ±1°. The proposed framework provides a reliable basis for springback prediction and rational design of additively manufactured polymer tools for air-bending applications.
- 23 December 2025
- Published by MDPI AG in Preprints.org
Open AccessAn Experimental–Numerical Framework for Springback Prediction and Angle Compensation in Air Bending with Additively Manufactured Polymer Tools
Additive manufacturing of polymer tools represents a promising alternative to conventional steel tooling for low-force and low-volume sheet metal air bending. However, accurate prediction of sheet springback and the resulting deviation of the bending angle after elastic unloading remains a major challenge. This study presents an integrated experimental–numerical framework for the analysis of air bending with additively manufactured polymer tools, with emphasis on material characterization, springback prediction, and tool angle compensation. The methodology combines uniaxial tensile testing, controlled air-bending experiments, finite element modelling with rigid and deformable tools, and optical 3D scanning for angle measurement. Low-carbon steel DC04 sheets were modeled using an elastoplastic constitutive law, while FDM-printed ABS tools were described by experimentally calibrated material models. Numerical simulations were performed over a range of forming forces to evaluate springback behavior and elastic tool deformation. The results show very good agreement between experiments and simulations. Deviations in bending angle were below 1.5% for metallic tools and below 0.5% for springback compensation, with the smallest discrepancy obtained using a two-dimensional model with deformable tools. Experimental validation with ABS tools confirmed bending accuracy within ±1°. The proposed framework provides a reliable basis for springback prediction and rational design of additively manufactured polymer tools for air-bending applications.
- Open Access
Material Extrusion 3D Printing of Micro-Porous Copper-Based Structure for Water Filters
This paper presents 3D-printed micro-porous structures made of a Cu/PLA composite by using material extrusion 3D printing technology. A metallic filament made of 80% copper and 20% polylactic acid (PLA) was used for the 3D printing of the porous samples. We varied printing parameters, aiming to obtain a micro-range porosity that can serve as a water-filtering structure. The produced samples were analyzed from the aspects of dimensional accuracy, level of porosity, and capacity for water flow. Several samples were fabricated, and the water flow was exhibited for the samples with an approximate 100 µm size of the interconnected open porosity. The application of material extrusion 3D printing, as a cost-effective, widely available technology for producing micro-range porous structures, is still challenging, especially for interconnected predefined porosity with metal-based filaments. Our research showed that the optimization of 3D printing parameters can enable the fabrication of copper-based micro-porous structures, but further research is still needed.
Open AccessMaterial Extrusion 3D Printing of Micro-Porous Copper-Based Structure for Water Filters
This paper presents 3D-printed micro-porous structures made of a Cu/PLA composite by using material extrusion 3D printing technology. A metallic filament made of 80% copper and 20% polylactic acid (PLA) was used for the 3D printing of the porous samples. We varied printing parameters, aiming to obtain a micro-range porosity that can serve as a water-filtering structure. The produced samples were analyzed from the aspects of dimensional accuracy, level of porosity, and capacity for water flow. Several samples were fabricated, and the water flow was exhibited for the samples with an approximate 100 µm size of the interconnected open porosity. The application of material extrusion 3D printing, as a cost-effective, widely available technology for producing micro-range porous structures, is still challenging, especially for interconnected predefined porosity with metal-based filaments. Our research showed that the optimization of 3D printing parameters can enable the fabrication of copper-based micro-porous structures, but further research is still needed.
- Open Access
- 26 May 2024
- Published by Stowarzyszenie Menedzerow Jakosci i Produkcji in Production Engineering Archives
- Vol. 30 (2) , 225-232
Predicting the mechanical properties of stainless steels using Artificial Neural Networks
Knowing the material properties is of a crucial importance when planning to manufacture some structure. That is true for the steel structures, as well. Thus, for the proper planning of a certain steel part or a structure production, one must be aware of the properties of the material, to be able to make a qualified decision, which material should be used. Considering that the manufacturing of steel products is constantly growing in various branches of industry and engineering, the problem of predicting the material properties, needed to satisfy the requirements for the certain part efficient and reliable functioning, becomes an imperative in the design process. A method of predicting four material properties of the two stainless steels, by use of the artificial neural network (ANN) is presented in this article. Those properties were predicted based on the particular steels’ known chemical compositions and the corresponding material properties available in the Cambridge Educational System EDU PACK 2010 software, using neural network module of MathWorks Matlab. The method was verified by comparing the values of the material properties predicted by this method to known values of properties for the two stainless steels, X5CrNi18-10 (AISI 304), X5CrNiMo17-12-2 (AISI 316). The difference between the two sets of values was below 5% and, in some cases, even negligible.
- 26 May 2024
- Published by Stowarzyszenie Menedzerow Jakosci i Produkcji in Production Engineering Archives
- Vol. 30 (2) , 225-232
Open AccessPredicting the mechanical properties of stainless steels using Artificial Neural Networks
Knowing the material properties is of a crucial importance when planning to manufacture some structure. That is true for the steel structures, as well. Thus, for the proper planning of a certain steel part or a structure production, one must be aware of the properties of the material, to be able to make a qualified decision, which material should be used. Considering that the manufacturing of steel products is constantly growing in various branches of industry and engineering, the problem of predicting the material properties, needed to satisfy the requirements for the certain part efficient and reliable functioning, becomes an imperative in the design process. A method of predicting four material properties of the two stainless steels, by use of the artificial neural network (ANN) is presented in this article. Those properties were predicted based on the particular steels’ known chemical compositions and the corresponding material properties available in the Cambridge Educational System EDU PACK 2010 software, using neural network module of MathWorks Matlab. The method was verified by comparing the values of the material properties predicted by this method to known values of properties for the two stainless steels, X5CrNi18-10 (AISI 304), X5CrNiMo17-12-2 (AISI 316). The difference between the two sets of values was below 5% and, in some cases, even negligible.
- Open Access
- 15 April 2024
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 31 (2) , 579-586
Experimental and Numerical Analyses of the Temperature Field in the Ironing Process
The purpose of this paper is to determine the temperature fields in the workpiece and the tool in the ironing process using an integrated approach that includes laboratory experiments and numerical modelling. An originally developed model device for...
- 15 April 2024
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 31 (2) , 579-586
Open AccessExperimental and Numerical Analyses of the Temperature Field in the Ironing Process
The purpose of this paper is to determine the temperature fields in the workpiece and the tool in the ironing process using an integrated approach that includes laboratory experiments and numerical modelling. An originally developed model device for...
- Open Access
- 1 January 2024
- Published by Centre for Evaluation in Education and Science (CEON/CEES)
- No. Materials ,p. 452-456
Influence of tempering temperature on mechanical properties of G42CrMo4 cast steel
This paper explores the effects of tempering temperatures on the mechanical properties of G42CrMo4 cast steel, a versatile alloy commonly used in automotive and construction industries. Tempering, a critical step in the heat treatment process, aims to reduce residual stresses and enhance material reliability. The study investigates the influence of tempering temperatures (450°C and 600°C) on the steel's strength, ductility, and hardness through a series of experimental investigations, including heat treatment, machining, and tensile testing. Results indicate that while normalization treatment offers moderate strength and good ductility, quenching and tempering at 450°C significantly increase strength at the expense of ductility. Conversely, tempering at 600°C strikes a balance between strength and ductility.
- 1 January 2024
- Published by Centre for Evaluation in Education and Science (CEON/CEES)
- No. Materials ,p. 452-456
Open AccessInfluence of tempering temperature on mechanical properties of G42CrMo4 cast steel
This paper explores the effects of tempering temperatures on the mechanical properties of G42CrMo4 cast steel, a versatile alloy commonly used in automotive and construction industries. Tempering, a critical step in the heat treatment process, aims to reduce residual stresses and enhance material reliability. The study investigates the influence of tempering temperatures (450°C and 600°C) on the steel's strength, ductility, and hardness through a series of experimental investigations, including heat treatment, machining, and tensile testing. Results indicate that while normalization treatment offers moderate strength and good ductility, quenching and tempering at 450°C significantly increase strength at the expense of ductility. Conversely, tempering at 600°C strikes a balance between strength and ductility.
- Open Access
Multi-Criteria Decision Making Methods for Selection of Lightweight Material for Railway Vehicles
This paper deals with the selection of the optimal material for railway wagons, from among three different steel and three aluminium based materials, by using four different Multicriteria Decision Making Methods (MCDM) and comparing their ranking of the materials. We analysed: Dual-Phase 600 steel, Transformation-Induced Plasticity (TRIP) 700 steel, Twinning-Induced Plasticity (TWIP) steel, Aluminium (Al) alloys, Al 6005-T6, and Al 6082-T6, and porous Al structure with closed cells. Four different MCDM methods were used: VIKOR, TOPSIS, PROMETTHEE and the Weighted aggregated sum product assessment method (WASPAS). Key material properties that were used in the MCDM analysis were: density, yield strength (Y.S.), tensile strength (T.S.), Y.S./T.S. ratio, Youngs modulus (Y.M.), cost and corrosion resistance (C.R.). Research results indicate that aluminium and its alloys prove to be the most suitable material, based on setup criteria. Advanced steels also achieved good ranking, making them a valid option, immediately behind lightweight aluminium alloys. Porous aluminium did not perform well, according to the used MDCM methods, mainly due to the significantly lower strength exhibited by the porous structures in general.
Open AccessMulti-Criteria Decision Making Methods for Selection of Lightweight Material for Railway Vehicles
This paper deals with the selection of the optimal material for railway wagons, from among three different steel and three aluminium based materials, by using four different Multicriteria Decision Making Methods (MCDM) and comparing their ranking of the materials. We analysed: Dual-Phase 600 steel, Transformation-Induced Plasticity (TRIP) 700 steel, Twinning-Induced Plasticity (TWIP) steel, Aluminium (Al) alloys, Al 6005-T6, and Al 6082-T6, and porous Al structure with closed cells. Four different MCDM methods were used: VIKOR, TOPSIS, PROMETTHEE and the Weighted aggregated sum product assessment method (WASPAS). Key material properties that were used in the MCDM analysis were: density, yield strength (Y.S.), tensile strength (T.S.), Y.S./T.S. ratio, Youngs modulus (Y.M.), cost and corrosion resistance (C.R.). Research results indicate that aluminium and its alloys prove to be the most suitable material, based on setup criteria. Advanced steels also achieved good ranking, making them a valid option, immediately behind lightweight aluminium alloys. Porous aluminium did not perform well, according to the used MDCM methods, mainly due to the significantly lower strength exhibited by the porous structures in general.
- 5 November 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 236 (10) , 2004-2012
Influence of different environments on the sliding friction of Ultra-high-molecular-weight polyethylene (UHMWPE)
Dynamic friction coefficient (COF) of the reciprocating sliding contact of the conventional UHMWPE, was investigated in four different environments (dry contact; distilled water; pure Ringer's solution and with PMMA particles), at five values of low normal load (0.1–1 N) and three values of sliding speed (4 - 12 mm/s). Significant differences of COF values occurred at the lowest load (0.1 N), whereas sliding speed did not influence COF values. Addition of PMMA particles in Ringer's solution produced significant increase of COF values, especially at the lowest load of 0.1 N. For the dry contact and the highest load (1 N), steady state was reached shortly after the beginning of the test and friction coefficient had uniform behaviour. In the case of wet environment and the lowest load, steady state was not reached and the friction coefficient exhibited non-reproducible random behaviour. According to the Hertz theory, 0.5 N load corresponded to the elastic stress of 48.7 MPa, thus surpassing the values of the elastic limits, hardness and true yield stress of the UHMWPE, and the behaviour of the friction coefficient was drastically different below and above this load value. It can be assumed that below the 0.5 N load, viscoelastic response, accompanied with plastic deformation is dominant, with transition to mainly plastic deformation for the higher loads.
- 5 November 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 236 (10) , 2004-2012
Influence of different environments on the sliding friction of Ultra-high-molecular-weight polyethylene (UHMWPE)
Dynamic friction coefficient (COF) of the reciprocating sliding contact of the conventional UHMWPE, was investigated in four different environments (dry contact; distilled water; pure Ringer's solution and with PMMA particles), at five values of low normal load (0.1–1 N) and three values of sliding speed (4 - 12 mm/s). Significant differences of COF values occurred at the lowest load (0.1 N), whereas sliding speed did not influence COF values. Addition of PMMA particles in Ringer's solution produced significant increase of COF values, especially at the lowest load of 0.1 N. For the dry contact and the highest load (1 N), steady state was reached shortly after the beginning of the test and friction coefficient had uniform behaviour. In the case of wet environment and the lowest load, steady state was not reached and the friction coefficient exhibited non-reproducible random behaviour. According to the Hertz theory, 0.5 N load corresponded to the elastic stress of 48.7 MPa, thus surpassing the values of the elastic limits, hardness and true yield stress of the UHMWPE, and the behaviour of the friction coefficient was drastically different below and above this load value. It can be assumed that below the 0.5 N load, viscoelastic response, accompanied with plastic deformation is dominant, with transition to mainly plastic deformation for the higher loads.
- 21 October 2017
- Published by Springer Nature
- p. 225-280
Biodegradable Metals as Biomaterials for Clinical Practice: Iron-Based Materials
- 21 October 2017
- Published by Springer Nature
- p. 225-280
Biodegradable Metals as Biomaterials for Clinical Practice: Iron-Based Materials