GCGuodong Cao

Guodong Cao

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Guodong Cao has a total of 27 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Investigation of vibration on rheological behavior of fresh concrete using CFD-DEM coupling method

    by Guodong Cao, Yalong Bai, Yihao Shi, Zhuguo Li, Daiqiang Deng, Shengqiang Jiang, Sheng Xie, Hui Wang


  • Open Access

    Numerical Study on Effect of Aggregate Moisture on Mixing Process

    by Guodong Cao, Sheng Xie, Daiqiang Deng, Shengqiang Jiang

    During the concrete mixing process, the transition of aggregates from a dry to a moist state introduces a crucial dynamic that significantly influences particle interaction, consequently impacting mixing homogeneity. In this paper, based on the discrete element method, the effect of aggregate moisture on the mixing process of sand and stone was investigated. The interaction between dry particles was described by the Hertz–Mindlin model, while the interaction between wet particles was calculated by the linear cohesion model considering the liquid bridge force. Additionally, a functional relationship between the moisture content and the parameters of the linear cohesive contact model was established. The results show that the numerical method can be employed to simulate the mixing process. Notably, when the moisture content of pebbles ranges from 0% to 0.75% and that of sand ranges from 0% to 10.9%, the linear cohesion model is deemed suitable. The standard deviation of the mixing homogeneity of wet particles is lower than that of dry particles for short mixing time, indicating that a small amount of liquid enhances mixing homogeneity. However, moisture has no obvious effect on mixing homogeneity for a long mixing time. This nuanced understanding of the interplay between moisture, particle interactions, and mixing duration contributes valuable insights to optimize concrete mixing processes.


  • Open Access

    Study on Solidification Characteristics of Granular Coal Gangue: Fine Sand Paste-Cemented Filling Materials

    by Daiqiang Deng, Runze Wang, Guodong Cao, Yihua Liang, Jinkuan Fan, Yunfan Ma, Yu Gao

    Three groups of filling materials with different mix proportions were prepared. PO42.5 grade cement was selected as the binding material, mechanized granular coal gangue and fine sand were used as the filling aggregate, and then the specimens were curing at room temperature and 95% moisture. Through the uniaxial compression test, the influence of gangue–sand ratio, the mass fraction, and curing age on the mechanical properties of filling materials was analyzed. The microstructure analysis of SEM was conducted to explore the internal mechanism of the strength difference of filling materials. The results show that the gangue–sand ratio dramatically influences the uniaxial compressive strength. The strength increases first and then decreases with the gangue–sand ratio increase. The mass fraction of filling paste is positively correlated with specimen strength. When the sand–cement ratio, gangue–sand ratio, and the mass fraction remain unchanged, the longer the curing age, the greater the uniaxial compressive strength of specimens. The specimens with a sand–cement ratio of 3.5 : 1, a gangue–sand ratio of 5 : 5, and a mass fraction of 86% reach the maximum value of 11.03 MPa at a curing age of 10 days. It can be seen that when the gangue–sand ratio is 5 : 5, the filling material has the best mechanical properties, so it can be recommended as the optimal mix proportion for goaf filling. Thus, it provides a solid technical guarantee for the treatment of mine surface collapse disasters and the utilization of bulk coal gangue resources.


  • Open Access

    Study on Sound Propagation Performance of Mechanized Coal Gangue-Fine Sand Filling Body

    by Daiqiang Deng, Jinkuan Fan, Guodong Cao, Yihua Liang, Runze Wang, Yu Gao, Yunfan Ma

    In the process of continuous and high-intensity mining in soft rock coal mines, high-quality filling treatment is required for the goaf. A nondestructive acoustic velocimetry method is an excellent way to measure the quality of filling body to effectively maintain the rock stability of the mining area and decrease industrial solid waste. In this study, the gangue and fine sand are used as the filling aggregates, and the uniaxial compression test and acoustic wave test are conducted in the cementitious gangue-sand filling body with different gangue-sand ratio. The results show that the longitudinal wave velocity of the filling body is basically between 1.556 km/s and 2.413 km/s. When the gangue-sand ratio is small, and the slurry concentration is high, the early strength of the cementitious gangue-sand filling body is low, but the later strength has a good growth trend. For specimens with higher strength-filled bodies, the propagation speed of sound waves inside them is also faster, indicating a certain positive correlation between the strength of the filled body and the speed of sound waves. A mathematical equation using longitudinal wave velocity to predict the strength of filling body is established. This equation can be used to predict and judge the quality of the filling body in the mining area.


  • Open Access

    Analysis and Improvement of Oversize Goaf Backfill Engineering Based on Fuzzy Theory

    by Daiqiang Deng, Guodong Cao, Yihua Liang, Jinkuan Fan, Runze Wang, Yunfan Ma

    For the mine of large goaf, there are many factors that affect the filling quality. In order to improve the filling quality, it is necessary to identify the factors that have a significant impact. In this paper, the fuzzy mathematical method was used to analyze the five main factors (PC32.5cement sand ratio, slurry concentration, number of slurry lowering, dehydration and drainage, and tailing particle size grading) affecting the filling quality. The priority of each influence factor was calculated, and the priority set was established. It is found that the slurry launching point and particle size grading of the tailings have an obvious effect on filling quality. After increasing the slurry launching point and optimizing the particle size grading, the strength and uniformity of the filling body are improved.

  • Open Access

    Strength Model of Cemented Filling Body Based on a Neural Network Algorithm

    by Daiqiang Deng, Yihua Liang, Guodong Cao, Jinkuan Fan

    As one of the key measures for comprehensive management of goaf in various mines, filling mining has been recognized by practitioners in recent years due to its functions (e.g., resource utilization of solid waste and thorough goaf treatment). The performance of the filling material is the core challenge of filling mining, and it is influenced by the settling speed, conveying characteristics, and filling body strength. To understand the strength characteristics of a cemented filling body composed of medium-fine tailings, in this study, filling material ratio tests under different content of cement, tailings, and water were conducted. A backpropagation (BP) neural network topology structure was established in this study. The strength after different curing times was used as the output variable to analyze the impact of the cement, tailings, and water content on the filling body. A 3-Hn-3 structural model was employed. When the number of hidden layers Hn was 7, the model achieved the best learning and training effect. The results show that the predicted value, which is close to the measured value (fitting accuracy of 92.43–99.92%; average error of 0.0792–7.5682%), satisfies the engineering requirements. The neural network model can be employed to predict the filling body’s strength and provide a good reference to analyze the change law in the filling body’s strength.


  • Open Access

    Experimental Study on Lead-Smelting Slag as Paste Filling Cementing Material

    by Daiqiang Deng, Guodong Cao, Yihua Liang

    Under the current pressure of mineral product price and market competition, as well as the tightening of ecological and environmental protection policies, energy saving, emission reduction and cost reduction, and efficiency increase have become inevitable trends. Lead-smelting slag of smelter, as an industrial byproduct, is harmful solid waste to be eliminated. In this research, a series of experiments on substitute for cement were done for filling cost reduction under premise of guaranteeing the filling strength, using PC32.5 cement as reference cementing material. Meanwhile, with Portland cement clinker, water quenching slag of BF ironmaking, and lead-smelting slag of smelter in different ratios, four cementing materials were made and named as cementing material I, cementing material II, cementing material III, and cementing material IV. Then, the above five cementing materials including PC32.5 cement were mixed, respectively, with tailing and water to prepare paste backfill slurry with different binder-tailing ratio and concentration. Backfill block was made and cured at 20°C; their uniaxial compressive strengths in different curing ages were measured. The result shows the strength of backfill test block using cementing material I (cement clinker and water quenching slag) without lead-smelting slag is far higher than that of test block using PC32.5 cement as cementing material. The strength of block with 16% lead-smelting slag increased dramatically, which was higher than the strength of block using PC32.5 as cementing material. However, the strength of test block decreased when the content of lead-smelting slag reached 32% and 40%. The more lead-smelting slag was added, the worse influence on strength of backfill would be. Because of large specific gravity of lead-smelting slag and low content of CaO, the hydration activity of lead-smelting slag is far lower than that of water quenching slag. Therefore, using moderate lead-smelting slag as substitute for cement will lead to increase of backfill strength and decrease filling cost.


  • Open Access

    Optimization of the Stirring Blade Structure of the Pumping Unit Based on the Improvement of Concrete Suction Efficiency

    by Shengqiang Jiang, Hong Wan, Guodong Cao, Yuanqiang Tan, Jingang Liu, Shiping Yang, Xiangwu Xiao, Zhenggang Tong, Quanxu Yu

    In this paper, a discrete element method (DEM) is used to simulate the suction process of fresh concrete in the pumping system, and the influence of the stirring blade on the suction is explored. The Hertz‐Mindlin with JKR Cohesion contact model is used to establish the DEM model of fresh concrete, and the suction work is realized by an API function of DEM, and the movement of particles in the suction cylinder can be completed smoothly. The changes of the concrete flow field during the suction process are further studied, and the influence mechanism of the stirring blade on the suction process is explained. A numerical simulation scheme is designed to explore the influence of the rotation speed, installation angle, and edges distance of the stirring blade on the suction efficiency and the stirring resistance torque, and the structure of the stirring blade is optimized according to the influence law. The simulation results show that the stirring resistance torque of the optimized stirring blade is reduced without the suction efficiency of the pumping system reduced, and the stirring energy consumption of the pump suction is reduced.


  • Open Access

    Filling Treatment of Surface Subsidence Resulted From Underground Mining in a High-Altitude Mine

    by Daiqiang Deng, Guodong Cao, Yihua Liang

    In the process of filling the goaf of Huashugou copper mine, the filling aggregate was the mine’s self-produced copper flotation tailings. The physical and chemical property tests showed that the tailings were relatively fine, and the cumulative contents of the 7.5, 15, 80, and 90 μm particles were 56.99, 79.46, 99.88, and 100%, respectively. PSA42.5 Portland slag cement was selected as the cementing material for the tests. The amount of finely ground blast furnace slag added to the cement was 20–50%. The filling test blocks of all proportions were demolded within 24–36 h, and the integrity of the formed filling bodies was satisfactory. Among them, the uniaxial compressive strength of the test block formed by the filling slurry with a tailings-to-cement ratio of 3/1 and a concentration of 74% after 3, 7, 28, and 60 days reached 0.833, 2.026, 4.520, and 6.560 MPa, respectively. The strengths of the other filling blocks also met the engineering design requirements. Based on the statistical regression analysis method, the influences of the slag cement content χ₁ and the tailings water content χ₂ on the filling body’s strength Ϭ were analyzed. The regression calculation also considered the interaction between χ₁ and χ₂, and the obtained multiple nonlinear regression model successfully predicted Ϭ. In production and application, the large density of tailings would accelerate their settling, which could easily cause blockage during the transportation of filling slurry through the pipeline. Regarding a series of existing filling materials and technical conditions, the filling process investigated in this study overcomes several unfavorable conditions. Using advanced and reliable technology and an industrial filling pump with a delivery pressure of 10 MPa, the prepared filling slurry concentration was 68–72% and the flow rate was 56–79 m3/h. The tailings and PSA42.5 Portland slag cement combined quite well. The filling body in the goaf demonstrated excellent homogeneity, and the various industrial indicators met the technical requirements for mining deposits. The preparation of high-quality filling materials with a smooth filling process has played a positive role in the prevention and treatment of surface mountain cracks and collapse during underground mining in high-altitude areas.