Yihua Liang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yihua Liang has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Guodong Cao
College of Civil Engineering, Xiangtan University, Xiangtan 411105, China
6 shared publications - Daiqiang Deng
College of Civil Engineering, Xiangtan University, Xiangtan 411105, China
5 shared publications - Jinkuan Fan
College of Civil Engineering, Xiangtan University, Xiangtan 411105, China
4 shared publications - Runze Wang
College of Civil Engineering, Xiangtan University, Xiangtan 411105, China
3 shared publications - Yunfan Ma
College of Civil Engineering, Xiangtan University, Xiangtan 411105, China
3 shared publications Daiqiang Deng
College of Civil Engineering, Xiangtan University, Xiangtan, China
2 shared publications
Latest Publications
- Open Access
- 16 September 2023
- Published by Wiley in Advances in Civil Engineering
- Vol. 2023, 1-10
Study on Solidification Characteristics of Granular Coal Gangue: Fine Sand Paste-Cemented Filling Materials
Three groups of filling materials with different mix proportions were prepared. PO42.5 grade cement was selected as the binding material, mechanized granular coal gangue and fine sand were used as the filling aggregate, and then the specimens were curing at room temperature and 95% moisture. Through the uniaxial compression test, the influence of gangue–sand ratio, the mass fraction, and curing age on the mechanical properties of filling materials was analyzed. The microstructure analysis of SEM was conducted to explore the internal mechanism of the strength difference of filling materials. The results show that the gangue–sand ratio dramatically influences the uniaxial compressive strength. The strength increases first and then decreases with the gangue–sand ratio increase. The mass fraction of filling paste is positively correlated with specimen strength. When the sand–cement ratio, gangue–sand ratio, and the mass fraction remain unchanged, the longer the curing age, the greater the uniaxial compressive strength of specimens. The specimens with a sand–cement ratio of 3.5 : 1, a gangue–sand ratio of 5 : 5, and a mass fraction of 86% reach the maximum value of 11.03 MPa at a curing age of 10 days. It can be seen that when the gangue–sand ratio is 5 : 5, the filling material has the best mechanical properties, so it can be recommended as the optimal mix proportion for goaf filling. Thus, it provides a solid technical guarantee for the treatment of mine surface collapse disasters and the utilization of bulk coal gangue resources.
- 16 September 2023
- Published by Wiley in Advances in Civil Engineering
- Vol. 2023, 1-10
Open AccessStudy on Solidification Characteristics of Granular Coal Gangue: Fine Sand Paste-Cemented Filling Materials
Three groups of filling materials with different mix proportions were prepared. PO42.5 grade cement was selected as the binding material, mechanized granular coal gangue and fine sand were used as the filling aggregate, and then the specimens were curing at room temperature and 95% moisture. Through the uniaxial compression test, the influence of gangue–sand ratio, the mass fraction, and curing age on the mechanical properties of filling materials was analyzed. The microstructure analysis of SEM was conducted to explore the internal mechanism of the strength difference of filling materials. The results show that the gangue–sand ratio dramatically influences the uniaxial compressive strength. The strength increases first and then decreases with the gangue–sand ratio increase. The mass fraction of filling paste is positively correlated with specimen strength. When the sand–cement ratio, gangue–sand ratio, and the mass fraction remain unchanged, the longer the curing age, the greater the uniaxial compressive strength of specimens. The specimens with a sand–cement ratio of 3.5 : 1, a gangue–sand ratio of 5 : 5, and a mass fraction of 86% reach the maximum value of 11.03 MPa at a curing age of 10 days. It can be seen that when the gangue–sand ratio is 5 : 5, the filling material has the best mechanical properties, so it can be recommended as the optimal mix proportion for goaf filling. Thus, it provides a solid technical guarantee for the treatment of mine surface collapse disasters and the utilization of bulk coal gangue resources.
- Open Access
- 5 June 2023
- Published by Wiley in Shock and Vibration
- Vol. 2023, 1-10
Study on Sound Propagation Performance of Mechanized Coal Gangue-Fine Sand Filling Body
In the process of continuous and high-intensity mining in soft rock coal mines, high-quality filling treatment is required for the goaf. A nondestructive acoustic velocimetry method is an excellent way to measure the quality of filling body to effectively maintain the rock stability of the mining area and decrease industrial solid waste. In this study, the gangue and fine sand are used as the filling aggregates, and the uniaxial compression test and acoustic wave test are conducted in the cementitious gangue-sand filling body with different gangue-sand ratio. The results show that the longitudinal wave velocity of the filling body is basically between 1.556 km/s and 2.413 km/s. When the gangue-sand ratio is small, and the slurry concentration is high, the early strength of the cementitious gangue-sand filling body is low, but the later strength has a good growth trend. For specimens with higher strength-filled bodies, the propagation speed of sound waves inside them is also faster, indicating a certain positive correlation between the strength of the filled body and the speed of sound waves. A mathematical equation using longitudinal wave velocity to predict the strength of filling body is established. This equation can be used to predict and judge the quality of the filling body in the mining area.
- 5 June 2023
- Published by Wiley in Shock and Vibration
- Vol. 2023, 1-10
Open AccessStudy on Sound Propagation Performance of Mechanized Coal Gangue-Fine Sand Filling Body
In the process of continuous and high-intensity mining in soft rock coal mines, high-quality filling treatment is required for the goaf. A nondestructive acoustic velocimetry method is an excellent way to measure the quality of filling body to effectively maintain the rock stability of the mining area and decrease industrial solid waste. In this study, the gangue and fine sand are used as the filling aggregates, and the uniaxial compression test and acoustic wave test are conducted in the cementitious gangue-sand filling body with different gangue-sand ratio. The results show that the longitudinal wave velocity of the filling body is basically between 1.556 km/s and 2.413 km/s. When the gangue-sand ratio is small, and the slurry concentration is high, the early strength of the cementitious gangue-sand filling body is low, but the later strength has a good growth trend. For specimens with higher strength-filled bodies, the propagation speed of sound waves inside them is also faster, indicating a certain positive correlation between the strength of the filled body and the speed of sound waves. A mathematical equation using longitudinal wave velocity to predict the strength of filling body is established. This equation can be used to predict and judge the quality of the filling body in the mining area.
- Open Access
- 22 April 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (9) , 5235
Analysis and Improvement of Oversize Goaf Backfill Engineering Based on Fuzzy Theory
For the mine of large goaf, there are many factors that affect the filling quality. In order to improve the filling quality, it is necessary to identify the factors that have a significant impact. In this paper, the fuzzy mathematical method was used to analyze the five main factors (PC32.5cement sand ratio, slurry concentration, number of slurry lowering, dehydration and drainage, and tailing particle size grading) affecting the filling quality. The priority of each influence factor was calculated, and the priority set was established. It is found that the slurry launching point and particle size grading of the tailings have an obvious effect on filling quality. After increasing the slurry launching point and optimizing the particle size grading, the strength and uniformity of the filling body are improved.
- 22 April 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (9) , 5235
Open AccessAnalysis and Improvement of Oversize Goaf Backfill Engineering Based on Fuzzy Theory
For the mine of large goaf, there are many factors that affect the filling quality. In order to improve the filling quality, it is necessary to identify the factors that have a significant impact. In this paper, the fuzzy mathematical method was used to analyze the five main factors (PC32.5cement sand ratio, slurry concentration, number of slurry lowering, dehydration and drainage, and tailing particle size grading) affecting the filling quality. The priority of each influence factor was calculated, and the priority set was established. It is found that the slurry launching point and particle size grading of the tailings have an obvious effect on filling quality. After increasing the slurry launching point and optimizing the particle size grading, the strength and uniformity of the filling body are improved.
- Open Access
- 5 April 2023
- Published by Frontiers Media SA in Frontiers in Materials
- Vol. 10
Strength variation characteristics of waste tailings cemented backfill materials with ultrafine particles
This study investigates the use of self-produced solid waste in mines to backfill the goaf, with energy saving and emission reduction technology requirements. Using a relevant backfill mixing proportion test and mechanical property test, we analyzed the strength variation law of backfill materials under different concentrations and cementation powder addition. The results showed that, for backfill materials at 7 days with an ash-tailings ratio of 1:6, the strength of specimens with 52% and 49% prepared concentrations, respectively, increased by 1.361 and 1.266 times over specimens with 49% and 46% concentrations. For backfill materials with 49% prepared concentrations and ash-tailings ratios of 1:6, 1:9, and 1:12, the specimen strength of the backfill materials with ratios of 1:6 and 1:9 improved by 0.616 MPa and 0.321 MPa—109.28% and 114.6%, respectively—compared with 1:9 and 1:12 backfill materials at 60 days. It is thus evident that the quantity of binding materials added plays a critical function in improving the strength of backfill materials, and in the subsequent application of goaf backfill. The strength of backfill materials can be enhanced by improving the gradation of backfill aggregates and increasing the amount of binding materials so as to achieve cost reductions and sustainable development.
- 5 April 2023
- Published by Frontiers Media SA in Frontiers in Materials
- Vol. 10
Open AccessStrength variation characteristics of waste tailings cemented backfill materials with ultrafine particles
This study investigates the use of self-produced solid waste in mines to backfill the goaf, with energy saving and emission reduction technology requirements. Using a relevant backfill mixing proportion test and mechanical property test, we analyzed the strength variation law of backfill materials under different concentrations and cementation powder addition. The results showed that, for backfill materials at 7 days with an ash-tailings ratio of 1:6, the strength of specimens with 52% and 49% prepared concentrations, respectively, increased by 1.361 and 1.266 times over specimens with 49% and 46% concentrations. For backfill materials with 49% prepared concentrations and ash-tailings ratios of 1:6, 1:9, and 1:12, the specimen strength of the backfill materials with ratios of 1:6 and 1:9 improved by 0.616 MPa and 0.321 MPa—109.28% and 114.6%, respectively—compared with 1:9 and 1:12 backfill materials at 60 days. It is thus evident that the quantity of binding materials added plays a critical function in improving the strength of backfill materials, and in the subsequent application of goaf backfill. The strength of backfill materials can be enhanced by improving the gradation of backfill aggregates and increasing the amount of binding materials so as to achieve cost reductions and sustainable development.
- Open Access
- 29 April 2022
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2022, 1-10
Strength Model of Cemented Filling Body Based on a Neural Network Algorithm
As one of the key measures for comprehensive management of goaf in various mines, filling mining has been recognized by practitioners in recent years due to its functions (e.g., resource utilization of solid waste and thorough goaf treatment). The performance of the filling material is the core challenge of filling mining, and it is influenced by the settling speed, conveying characteristics, and filling body strength. To understand the strength characteristics of a cemented filling body composed of medium-fine tailings, in this study, filling material ratio tests under different content of cement, tailings, and water were conducted. A backpropagation (BP) neural network topology structure was established in this study. The strength after different curing times was used as the output variable to analyze the impact of the cement, tailings, and water content on the filling body. A 3-Hn-3 structural model was employed. When the number of hidden layers Hn was 7, the model achieved the best learning and training effect. The results show that the predicted value, which is close to the measured value (fitting accuracy of 92.43–99.92%; average error of 0.0792–7.5682%), satisfies the engineering requirements. The neural network model can be employed to predict the filling body’s strength and provide a good reference to analyze the change law in the filling body’s strength.
- 29 April 2022
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2022, 1-10
Open AccessStrength Model of Cemented Filling Body Based on a Neural Network Algorithm
As one of the key measures for comprehensive management of goaf in various mines, filling mining has been recognized by practitioners in recent years due to its functions (e.g., resource utilization of solid waste and thorough goaf treatment). The performance of the filling material is the core challenge of filling mining, and it is influenced by the settling speed, conveying characteristics, and filling body strength. To understand the strength characteristics of a cemented filling body composed of medium-fine tailings, in this study, filling material ratio tests under different content of cement, tailings, and water were conducted. A backpropagation (BP) neural network topology structure was established in this study. The strength after different curing times was used as the output variable to analyze the impact of the cement, tailings, and water content on the filling body. A 3-Hn-3 structural model was employed. When the number of hidden layers Hn was 7, the model achieved the best learning and training effect. The results show that the predicted value, which is close to the measured value (fitting accuracy of 92.43–99.92%; average error of 0.0792–7.5682%), satisfies the engineering requirements. The neural network model can be employed to predict the filling body’s strength and provide a good reference to analyze the change law in the filling body’s strength.
- Open Access
Experimental Study on Lead-Smelting Slag as Paste Filling Cementing Material
Under the current pressure of mineral product price and market competition, as well as the tightening of ecological and environmental protection policies, energy saving, emission reduction and cost reduction, and efficiency increase have become inevitable trends. Lead-smelting slag of smelter, as an industrial byproduct, is harmful solid waste to be eliminated. In this research, a series of experiments on substitute for cement were done for filling cost reduction under premise of guaranteeing the filling strength, using PC32.5 cement as reference cementing material. Meanwhile, with Portland cement clinker, water quenching slag of BF ironmaking, and lead-smelting slag of smelter in different ratios, four cementing materials were made and named as cementing material I, cementing material II, cementing material III, and cementing material IV. Then, the above five cementing materials including PC32.5 cement were mixed, respectively, with tailing and water to prepare paste backfill slurry with different binder-tailing ratio and concentration. Backfill block was made and cured at 20°C; their uniaxial compressive strengths in different curing ages were measured. The result shows the strength of backfill test block using cementing material I (cement clinker and water quenching slag) without lead-smelting slag is far higher than that of test block using PC32.5 cement as cementing material. The strength of block with 16% lead-smelting slag increased dramatically, which was higher than the strength of block using PC32.5 as cementing material. However, the strength of test block decreased when the content of lead-smelting slag reached 32% and 40%. The more lead-smelting slag was added, the worse influence on strength of backfill would be. Because of large specific gravity of lead-smelting slag and low content of CaO, the hydration activity of lead-smelting slag is far lower than that of water quenching slag. Therefore, using moderate lead-smelting slag as substitute for cement will lead to increase of backfill strength and decrease filling cost.
Open AccessExperimental Study on Lead-Smelting Slag as Paste Filling Cementing Material
Under the current pressure of mineral product price and market competition, as well as the tightening of ecological and environmental protection policies, energy saving, emission reduction and cost reduction, and efficiency increase have become inevitable trends. Lead-smelting slag of smelter, as an industrial byproduct, is harmful solid waste to be eliminated. In this research, a series of experiments on substitute for cement were done for filling cost reduction under premise of guaranteeing the filling strength, using PC32.5 cement as reference cementing material. Meanwhile, with Portland cement clinker, water quenching slag of BF ironmaking, and lead-smelting slag of smelter in different ratios, four cementing materials were made and named as cementing material I, cementing material II, cementing material III, and cementing material IV. Then, the above five cementing materials including PC32.5 cement were mixed, respectively, with tailing and water to prepare paste backfill slurry with different binder-tailing ratio and concentration. Backfill block was made and cured at 20°C; their uniaxial compressive strengths in different curing ages were measured. The result shows the strength of backfill test block using cementing material I (cement clinker and water quenching slag) without lead-smelting slag is far higher than that of test block using PC32.5 cement as cementing material. The strength of block with 16% lead-smelting slag increased dramatically, which was higher than the strength of block using PC32.5 as cementing material. However, the strength of test block decreased when the content of lead-smelting slag reached 32% and 40%. The more lead-smelting slag was added, the worse influence on strength of backfill would be. Because of large specific gravity of lead-smelting slag and low content of CaO, the hydration activity of lead-smelting slag is far lower than that of water quenching slag. Therefore, using moderate lead-smelting slag as substitute for cement will lead to increase of backfill strength and decrease filling cost.
- Open Access
- 25 October 2021
- Published by Frontiers Media SA in Frontiers in Materials
- Vol. 8
Filling Treatment of Surface Subsidence Resulted From Underground Mining in a High-Altitude Mine
In the process of filling the goaf of Huashugou copper mine, the filling aggregate was the mine’s self-produced copper flotation tailings. The physical and chemical property tests showed that the tailings were relatively fine, and the cumulative contents of the 7.5, 15, 80, and 90 μm particles were 56.99, 79.46, 99.88, and 100%, respectively. PSA42.5 Portland slag cement was selected as the cementing material for the tests. The amount of finely ground blast furnace slag added to the cement was 20–50%. The filling test blocks of all proportions were demolded within 24–36 h, and the integrity of the formed filling bodies was satisfactory. Among them, the uniaxial compressive strength of the test block formed by the filling slurry with a tailings-to-cement ratio of 3/1 and a concentration of 74% after 3, 7, 28, and 60 days reached 0.833, 2.026, 4.520, and 6.560 MPa, respectively. The strengths of the other filling blocks also met the engineering design requirements. Based on the statistical regression analysis method, the influences of the slag cement content χ₁ and the tailings water content χ₂ on the filling body’s strength Ϭ were analyzed. The regression calculation also considered the interaction between χ₁ and χ₂, and the obtained multiple nonlinear regression model successfully predicted Ϭ. In production and application, the large density of tailings would accelerate their settling, which could easily cause blockage during the transportation of filling slurry through the pipeline. Regarding a series of existing filling materials and technical conditions, the filling process investigated in this study overcomes several unfavorable conditions. Using advanced and reliable technology and an industrial filling pump with a delivery pressure of 10 MPa, the prepared filling slurry concentration was 68–72% and the flow rate was 56–79 m3/h. The tailings and PSA42.5 Portland slag cement combined quite well. The filling body in the goaf demonstrated excellent homogeneity, and the various industrial indicators met the technical requirements for mining deposits. The preparation of high-quality filling materials with a smooth filling process has played a positive role in the prevention and treatment of surface mountain cracks and collapse during underground mining in high-altitude areas.
- 25 October 2021
- Published by Frontiers Media SA in Frontiers in Materials
- Vol. 8
Open AccessFilling Treatment of Surface Subsidence Resulted From Underground Mining in a High-Altitude Mine
In the process of filling the goaf of Huashugou copper mine, the filling aggregate was the mine’s self-produced copper flotation tailings. The physical and chemical property tests showed that the tailings were relatively fine, and the cumulative contents of the 7.5, 15, 80, and 90 μm particles were 56.99, 79.46, 99.88, and 100%, respectively. PSA42.5 Portland slag cement was selected as the cementing material for the tests. The amount of finely ground blast furnace slag added to the cement was 20–50%. The filling test blocks of all proportions were demolded within 24–36 h, and the integrity of the formed filling bodies was satisfactory. Among them, the uniaxial compressive strength of the test block formed by the filling slurry with a tailings-to-cement ratio of 3/1 and a concentration of 74% after 3, 7, 28, and 60 days reached 0.833, 2.026, 4.520, and 6.560 MPa, respectively. The strengths of the other filling blocks also met the engineering design requirements. Based on the statistical regression analysis method, the influences of the slag cement content χ₁ and the tailings water content χ₂ on the filling body’s strength Ϭ were analyzed. The regression calculation also considered the interaction between χ₁ and χ₂, and the obtained multiple nonlinear regression model successfully predicted Ϭ. In production and application, the large density of tailings would accelerate their settling, which could easily cause blockage during the transportation of filling slurry through the pipeline. Regarding a series of existing filling materials and technical conditions, the filling process investigated in this study overcomes several unfavorable conditions. Using advanced and reliable technology and an industrial filling pump with a delivery pressure of 10 MPa, the prepared filling slurry concentration was 68–72% and the flow rate was 56–79 m3/h. The tailings and PSA42.5 Portland slag cement combined quite well. The filling body in the goaf demonstrated excellent homogeneity, and the various industrial indicators met the technical requirements for mining deposits. The preparation of high-quality filling materials with a smooth filling process has played a positive role in the prevention and treatment of surface mountain cracks and collapse during underground mining in high-altitude areas.