Teeranoot Chanthasopeephan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Teeranoot Chanthasopeephan has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Sakda Chinchouryrang
Mechanical Engineering Department, King Mongkut’s University of Technology Thonburi, Bangkok, Thailand
2 shared publications- Sasitorn Srisawadi
Department of Materials Science, and the Specialized Center of Rubber and Polymer Materials for Agriculture and Industry, CBLAST, Faculty of Science, Kasetsart University, Bangkok, Thailand
2 shared publications Siwat Liampipat
Mechanical Engineering Department, King Mongkut’s University of Technology Thonburi, Bangkok, Thailand
2 shared publicationsTossaporn Udomsap
Mechanical Engineering Department, King Mongkut’s University of Technology Thonburi, Bangkok, Thailand
2 shared publicationsAsiwan Kultongkham
Mechanical Engineering Department, Faculty of Engineering, King Mongkut’s University of Technology Thonburi, Bangkok
1 shared publication- Dung-An Wang
Natl Chung Hsing Univ, Grad Inst Precis Engn, Taichung 40227, Taiwan
1 shared publication
Latest Publications
- Open Access
- 29 September 2026
- Published by Elsevier in Polymer Testing
- Vol. 163
Testing-based evaluation of matrix polarity effects on electromechanical and piezoresistive responses of CCB–BaTiO3 hybrid rubber composites
- 29 September 2026
- Published by Elsevier in Polymer Testing
- Vol. 163
Open AccessTesting-based evaluation of matrix polarity effects on electromechanical and piezoresistive responses of CCB–BaTiO3 hybrid rubber composites
- Open Access
- 5 May 2026
- Published by SAGE Publications in International Journal of Advanced Robotic Systems
- Vol. 23 (3)
Design of a bidirectional compliant gripper for robotic object manipulation
This study presents the design and development of a monolithic compliant gripper with bidirectional actuation, enabling both active grasping and full release within a single structural unit. To address these directional constraints commonly observed in conventional compliant mechanisms, the design incorporates a flexure-based cartwheel hinge that provides symmetric deformation and enhanced orientation adaptability. The gripper geometry is obtained through topology optimization to maximize material efficiency and mechanical advantage. Finite-element analysis and experimental validation confirm that the 3D-printed structure (30 g) achieves substantial bidirectional displacement under a 5 N input force. Performance testing demonstrates stable grasping, with successful manipulation of cubic objects at inclination angles up to 40° and pyramidal objects up to 50°. The integration of the cartwheel hinge enables more pronounced bidirectional motion and increased rotational capability, with a hinge thickness of 0.3 mm allowing rotation exceeding 90°, thereby improving grasping adaptability. Additionally, the gripper employs a modular structural design that allows rapid scaling from a two-finger pinch to a four-finger wrap. This system provides a lightweight and versatile solution for complex robotic manipulation tasks without the need for hardware redesign.
- 5 May 2026
- Published by SAGE Publications in International Journal of Advanced Robotic Systems
- Vol. 23 (3)
Open AccessDesign of a bidirectional compliant gripper for robotic object manipulation
This study presents the design and development of a monolithic compliant gripper with bidirectional actuation, enabling both active grasping and full release within a single structural unit. To address these directional constraints commonly observed in conventional compliant mechanisms, the design incorporates a flexure-based cartwheel hinge that provides symmetric deformation and enhanced orientation adaptability. The gripper geometry is obtained through topology optimization to maximize material efficiency and mechanical advantage. Finite-element analysis and experimental validation confirm that the 3D-printed structure (30 g) achieves substantial bidirectional displacement under a 5 N input force. Performance testing demonstrates stable grasping, with successful manipulation of cubic objects at inclination angles up to 40° and pyramidal objects up to 50°. The integration of the cartwheel hinge enables more pronounced bidirectional motion and increased rotational capability, with a hinge thickness of 0.3 mm allowing rotation exceeding 90°, thereby improving grasping adaptability. Additionally, the gripper employs a modular structural design that allows rapid scaling from a two-finger pinch to a four-finger wrap. This system provides a lightweight and versatile solution for complex robotic manipulation tasks without the need for hardware redesign.
- Open Access
- 5 March 2026
- Published by Elsevier in Robotics and Autonomous Systems
- Vol. 201
A hybrid admittance control strategy for fluid-driven origami actuators in lower limb exoskeleton
- 5 March 2026
- Published by Elsevier in Robotics and Autonomous Systems
- Vol. 201
Open AccessA hybrid admittance control strategy for fluid-driven origami actuators in lower limb exoskeleton
- 14 April 2025
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 390
Comparative analysis of 3D printed and cast conductive rubber for enhanced tactile sensing applications
- 14 April 2025
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 390
Comparative analysis of 3D printed and cast conductive rubber for enhanced tactile sensing applications
- Open Access
- 1 April 2023
- Published by Springer Nature in BMC Biomedical Engineering
- Vol. 5 (1) , 1-12
Parametric study of a bubble removing device for hemodialysis
This paper sets out to design a device for removing bubbles during the process of hemodialysis. The concept is to guide the bubbles while traveling through the device and eventually the bubbles can be collected. The design focuses on the analysis of various parameters i.e. inlet diameter, inlet velocity and size of the pitch. The initial diameters of Models 1 and 2 have thread regions of 6 and 10 mm, respectively. Parameters: Swirl number, Taylor number, Lift coefficient along with pressure field are also implemented. Based on computational fluid dynamics analysis, the bubbles' average maximum equilibrium position for Model 1 reached 1.995 mm, being greater than that of Model 2, which attained 1.833 mm. Then, 16,000 bubbles were released into Model 1 to validate the performance of the model. This number of bubbles is typically found in the dialysis. Thus, it was found that 81.53% of bubbles passed through the radial region of 2.20 ± 0.30 mm. The appropriate collecting plane was at 100 mm, as measured from the inlet position along the axial axis. The Taylor number, Lift coefficient, and Swirl number proved to be significant parameters for describing the movement of the bubbles. Results were based on multiple inlet velocities. It is seen that Model 3, the improved model with unequal pitch, reached a maximum equilibrium position of 2.24 mm. Overall, results demonstrated that Model 1 was the best design compared to Models 2 and 3. Model 1 was found capable of guiding the bubbles to the edge location and did not generate extra bubbles. Thus, the parametric study, herein, can be used as a prototype for removing bubbles during the process of hemodialysis.
- 1 April 2023
- Published by Springer Nature in BMC Biomedical Engineering
- Vol. 5 (1) , 1-12
Open AccessParametric study of a bubble removing device for hemodialysis
This paper sets out to design a device for removing bubbles during the process of hemodialysis. The concept is to guide the bubbles while traveling through the device and eventually the bubbles can be collected. The design focuses on the analysis of various parameters i.e. inlet diameter, inlet velocity and size of the pitch. The initial diameters of Models 1 and 2 have thread regions of 6 and 10 mm, respectively. Parameters: Swirl number, Taylor number, Lift coefficient along with pressure field are also implemented. Based on computational fluid dynamics analysis, the bubbles' average maximum equilibrium position for Model 1 reached 1.995 mm, being greater than that of Model 2, which attained 1.833 mm. Then, 16,000 bubbles were released into Model 1 to validate the performance of the model. This number of bubbles is typically found in the dialysis. Thus, it was found that 81.53% of bubbles passed through the radial region of 2.20 ± 0.30 mm. The appropriate collecting plane was at 100 mm, as measured from the inlet position along the axial axis. The Taylor number, Lift coefficient, and Swirl number proved to be significant parameters for describing the movement of the bubbles. Results were based on multiple inlet velocities. It is seen that Model 3, the improved model with unequal pitch, reached a maximum equilibrium position of 2.24 mm. Overall, results demonstrated that Model 1 was the best design compared to Models 2 and 3. Model 1 was found capable of guiding the bubbles to the edge location and did not generate extra bubbles. Thus, the parametric study, herein, can be used as a prototype for removing bubbles during the process of hemodialysis.
- Open Access
- 1 March 2023
- Published by Springer Nature in ROBOMECH Journal
- Vol. 10 (1) , 1-11
Kinematics of platform stabilization using a 3-PRS parallel manipulator
In this paper, a 3-PRS (prismatic, revolute, and spherical) parallel manipulator for platform stabilization is designed. The main purpose of this device is to stabilize visual equipment, which is placed on top of a car to inspect electrical transmission cables, as part of routine maintenance. Due to the bulky and heavy infrared cameras used during inspections, a stabilizer platform has been designed to handle the weight of camera equipment up to 10 kg. This device consists of two major mechanisms. The first mechanism is able to adjust the angle of the camera. Thus, the user can focus the camera along the electric transmission lines. The second mechanism is stabilization. The mechanism serves to stabilize the orientation and position of the camera in the roll, pitch, and heave directions. To test the performance of the stabilization mechanism, the device is fed with the known value of the angle with regard to the input. As such, the device is trying to compensate for the change in angle. The results show that the errors between the input angles and compensated angles are in the range of 0.4–3%. Errors are seen to be within an acceptable range. It is significant that the resultant errors do not affect the orientation of the camera.
- 1 March 2023
- Published by Springer Nature in ROBOMECH Journal
- Vol. 10 (1) , 1-11
Open AccessKinematics of platform stabilization using a 3-PRS parallel manipulator
In this paper, a 3-PRS (prismatic, revolute, and spherical) parallel manipulator for platform stabilization is designed. The main purpose of this device is to stabilize visual equipment, which is placed on top of a car to inspect electrical transmission cables, as part of routine maintenance. Due to the bulky and heavy infrared cameras used during inspections, a stabilizer platform has been designed to handle the weight of camera equipment up to 10 kg. This device consists of two major mechanisms. The first mechanism is able to adjust the angle of the camera. Thus, the user can focus the camera along the electric transmission lines. The second mechanism is stabilization. The mechanism serves to stabilize the orientation and position of the camera in the roll, pitch, and heave directions. To test the performance of the stabilization mechanism, the device is fed with the known value of the angle with regard to the input. As such, the device is trying to compensate for the change in angle. The results show that the errors between the input angles and compensated angles are in the range of 0.4–3%. Errors are seen to be within an acceptable range. It is significant that the resultant errors do not affect the orientation of the camera.
- Open Access
- 24 October 2022
- Published by Springer Nature in Research Square
Kinematics of a Platform Stabilization using 3-PRS Parallel Manipulator
In this paper, a 3-PRS (prismatic, revolute, and spherical) parallel manipulator for platform stabilization is designed. The main purpose of this device is to stabilize visual equipment, which is placed on top of a car to inspect electrical transmission cables as part of routine maintenance. Due to the bulky and heavy infrared cameras used during inspections, a stabilizer platform has been designed to handle the weight of camera equipment up to 10 kg. This device consists of two major mechanisms. The first mechanism is able to adjust the angle of the camera. Thus, the user can focus the camera along the electric transmission lines. The second mechanism is for stabilization. The mechanism serves to stabilize the orientation and position of the camera in roll, pitch, and heave directions. To test the performance of the stabilization mechanism, the device is fed with the known value of the angle as regards input. As such, the device is trying to compensate for the change in angle. Results show that errors between input angles and compensated angles are in the range of 0.4-3%. Errors are seen to be within an acceptable range. It is significant that the resultant errors do not affect the orientation of the camera.
- 24 October 2022
- Published by Springer Nature in Research Square
Open AccessKinematics of a Platform Stabilization using 3-PRS Parallel Manipulator
In this paper, a 3-PRS (prismatic, revolute, and spherical) parallel manipulator for platform stabilization is designed. The main purpose of this device is to stabilize visual equipment, which is placed on top of a car to inspect electrical transmission cables as part of routine maintenance. Due to the bulky and heavy infrared cameras used during inspections, a stabilizer platform has been designed to handle the weight of camera equipment up to 10 kg. This device consists of two major mechanisms. The first mechanism is able to adjust the angle of the camera. Thus, the user can focus the camera along the electric transmission lines. The second mechanism is for stabilization. The mechanism serves to stabilize the orientation and position of the camera in roll, pitch, and heave directions. To test the performance of the stabilization mechanism, the device is fed with the known value of the angle as regards input. As such, the device is trying to compensate for the change in angle. Results show that errors between input angles and compensated angles are in the range of 0.4-3%. Errors are seen to be within an acceptable range. It is significant that the resultant errors do not affect the orientation of the camera.
- 21 September 2021
- Published by ASME International in Journal of Mechanisms and Robotics
- Vol. 14 (2)
Design of a Parallel Gripper Based on Topology Synthesis and Evolutionary Optimization
A compliant gripper with nearly parallel gripping motion is developed by a topology synthesis and a dimensional synthesis approach. The topology synthesis process can generate linkage-type compliant mechanisms. Suitable boundary conditions of the topology synthesis process are selected to achieve the desired functions of the device. The dimensional synthesis is based on an evolutionary optimal design process. To meet various design goals, a nondominated multi-objective genetic algorithm is selected for the optimal design process. A kinetostaic model based on the chained beam constraint model is developed for force–displacement analysis of the designs. Efficiency and accuracy of the design approach are proved by experiments. Appropriate linkage types of compliant mechanisms may be discovered by the topology optimization process before moving on to the dimensional synthesis to obtain final designs.
- 21 September 2021
- Published by ASME International in Journal of Mechanisms and Robotics
- Vol. 14 (2)
Design of a Parallel Gripper Based on Topology Synthesis and Evolutionary Optimization
A compliant gripper with nearly parallel gripping motion is developed by a topology synthesis and a dimensional synthesis approach. The topology synthesis process can generate linkage-type compliant mechanisms. Suitable boundary conditions of the topology synthesis process are selected to achieve the desired functions of the device. The dimensional synthesis is based on an evolutionary optimal design process. To meet various design goals, a nondominated multi-objective genetic algorithm is selected for the optimal design process. A kinetostaic model based on the chained beam constraint model is developed for force–displacement analysis of the designs. Efficiency and accuracy of the design approach are proved by experiments. Appropriate linkage types of compliant mechanisms may be discovered by the topology optimization process before moving on to the dimensional synthesis to obtain final designs.
- Open Access
- 18 March 2021
- Published by PAGEPress Publications in Journal of Agricultural Engineering
- Vol. 52 (1)
The design of a force feedback soft gripper for tomato harvesting
In smart farming, both artificial intelligence and robotic systems are applied in order to improve efficiency. In agriculture, for jobs such as seeding, monitoring, and harvesting, robots are widely used. When using robots to harvest fruit and vegetables, it is essential not to apply excessive force, as it may damage the harvest. In this paper, a soft robotic three-fingered gripper is presented. It was designed and analysed using the finite element method. Each finger is made of silicone rubber. The shape of the finger is designed so that it is capable of handling spherical shaped objects, such as tomatoes or oranges. When holding a tomato, the fingers apply the contact force. The fingers are actuated pneumatically and the force applied is also controlled by a micro controller. The pressure inside the air chamber of the finger is in the range of 0- 95 kPa. Force sensors are attached to the end of each finger to provide force feedback. Then, the holding force is adjusted and applied to the surface of the tomato. The gripper can successfully grasp tomatoes with a force less than the bio-yield of the tomatoes 2.57 N.
- 18 March 2021
- Published by PAGEPress Publications in Journal of Agricultural Engineering
- Vol. 52 (1)
Open AccessThe design of a force feedback soft gripper for tomato harvesting
In smart farming, both artificial intelligence and robotic systems are applied in order to improve efficiency. In agriculture, for jobs such as seeding, monitoring, and harvesting, robots are widely used. When using robots to harvest fruit and vegetables, it is essential not to apply excessive force, as it may damage the harvest. In this paper, a soft robotic three-fingered gripper is presented. It was designed and analysed using the finite element method. Each finger is made of silicone rubber. The shape of the finger is designed so that it is capable of handling spherical shaped objects, such as tomatoes or oranges. When holding a tomato, the fingers apply the contact force. The fingers are actuated pneumatically and the force applied is also controlled by a micro controller. The pressure inside the air chamber of the finger is in the range of 0- 95 kPa. Force sensors are attached to the end of each finger to provide force feedback. Then, the holding force is adjusted and applied to the surface of the tomato. The gripper can successfully grasp tomatoes with a force less than the bio-yield of the tomatoes 2.57 N.