Aiqing Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Aiqing Wu has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
Lei Fan
3 shared publicationsYihu Zhang
Key Laboratory of Geotechnical Mechanics and Engineering of Ministry of Water Resources, Changjiang River Scientific Research Institute, Wuhan, China
3 shared publicationsDing Xiuli
2 shared publicationsXiang Fu
2 shared publications- Bo Lu
School of Resources and Civil Engineering, Northeastern University, Shenyang 110819, China
1 shared publication - Dong Zhihong
Tencent, Beijing, China
1 shared publication
Latest Publications
- 8 September 2023
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 56 (12) , 8891-8906
A Field Model Test Method of Tunnel-Type Anchorages in Rock Mass and Its Application in Railway Suspension Bridge Engineering
- 8 September 2023
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 56 (12) , 8891-8906
A Field Model Test Method of Tunnel-Type Anchorages in Rock Mass and Its Application in Railway Suspension Bridge Engineering
- Open Access
- 1 October 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 861 (7) , 072092
A hydro-mechanical coupling study with DDA numerical method to valley deformation mechanism of Xiluodu hydro-power station
A comprehensive investigation to the characteristics of valley deformation in Xiluodu project is briefly reviewed. Extensions for hydro-mechanical coupling simulation with DDA method for reservoir impoundment has been firstly derived. The DDA numerical model by considering interactional aspects of original geological cross section, geo-stress state, and the reservoir impoundment, etc., is then established. Simulations for the given numerical model with different initial geo-stress state after the water impoundment are performed, and the results are compared with that of typical valley deformation measurements, and at last, the deformation mechanism in causes of changing of effective stress in the particular geological condition is discussed.
- 1 October 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 861 (7) , 072092
Open AccessA hydro-mechanical coupling study with DDA numerical method to valley deformation mechanism of Xiluodu hydro-power station
A comprehensive investigation to the characteristics of valley deformation in Xiluodu project is briefly reviewed. Extensions for hydro-mechanical coupling simulation with DDA method for reservoir impoundment has been firstly derived. The DDA numerical model by considering interactional aspects of original geological cross section, geo-stress state, and the reservoir impoundment, etc., is then established. Simulations for the given numerical model with different initial geo-stress state after the water impoundment are performed, and the results are compared with that of typical valley deformation measurements, and at last, the deformation mechanism in causes of changing of effective stress in the particular geological condition is discussed.
- 8 July 2021
- Published by Taylor & Francis
- p. 75-78
Stability study on the surrounding rock of the underground powerhouse in Shui Buya project by DDA
In order to evaluate the stability and excavated deformation of the underground powerhouse, DDA is used as one of numerical methods during the design stage. In this paper, by means of DDA, the development of deformation and state of stress for the main opening are studied under two situations of without reinforcement and reinforcement by rockbolts, and the maximum displacement and locations of they occurring are given. The computation results show the underground cavern after reinforcement using system bolts is stable, and bolts decrease effectively the deformation of rock masses surrounding the opening.
- 8 July 2021
- Published by Taylor & Francis
- p. 75-78
Stability study on the surrounding rock of the underground powerhouse in Shui Buya project by DDA
In order to evaluate the stability and excavated deformation of the underground powerhouse, DDA is used as one of numerical methods during the design stage. In this paper, by means of DDA, the development of deformation and state of stress for the main opening are studied under two situations of without reinforcement and reinforcement by rockbolts, and the maximum displacement and locations of they occurring are given. The computation results show the underground cavern after reinforcement using system bolts is stable, and bolts decrease effectively the deformation of rock masses surrounding the opening.
- 8 July 2021
- Published by Taylor & Francis
- p. 207-212
Application of block theory in underground cavern rock stability
Based on Bai-Se hydraulic engineering, a large-scare hydraulic engineering in China, application methods of Block Theory to underground cavern are introduced, including unlocated, located and stochastic block analysis, as well as block morphologic display, block stability analysis and reinforcement measures suggestion. In unlocated block analysis, block geometric figure is analyzed by assuming block maximum edge length according to joint average length by investigation in situ. Appearance of maximum key block in cavern is analyzed and shown, so as to determine key blocks which should be considered in support design. Based on block geometric figure and joint shear strength, block stability is computed, anchor force is suggested in order to assure block stable. In located block analysis, actual morphology of blocks, including concave blocks are analyzed and displayed according to investigation of joints in cavern, stability of block is analyzed and anchor support design program is checked subsequently. In stochastic block analysis, simulating net of joint and stochastic block in excavation face are studied and shown. During the study of application of key block theory in underground cavern, some new technologies are developed such as block morphology analysis by assuming block maximum edge length, concave block analysis and display, and especially stochastic block analysis. These new technologies may promote application of block theory in rock engineering.
- 8 July 2021
- Published by Taylor & Francis
- p. 207-212
Application of block theory in underground cavern rock stability
Based on Bai-Se hydraulic engineering, a large-scare hydraulic engineering in China, application methods of Block Theory to underground cavern are introduced, including unlocated, located and stochastic block analysis, as well as block morphologic display, block stability analysis and reinforcement measures suggestion. In unlocated block analysis, block geometric figure is analyzed by assuming block maximum edge length according to joint average length by investigation in situ. Appearance of maximum key block in cavern is analyzed and shown, so as to determine key blocks which should be considered in support design. Based on block geometric figure and joint shear strength, block stability is computed, anchor force is suggested in order to assure block stable. In located block analysis, actual morphology of blocks, including concave blocks are analyzed and displayed according to investigation of joints in cavern, stability of block is analyzed and anchor support design program is checked subsequently. In stochastic block analysis, simulating net of joint and stochastic block in excavation face are studied and shown. During the study of application of key block theory in underground cavern, some new technologies are developed such as block morphology analysis by assuming block maximum edge length, concave block analysis and display, and especially stochastic block analysis. These new technologies may promote application of block theory in rock engineering.
- 27 January 2012
- Published by Taylor & Francis
- p. 245-252
Three-dimensional block cutting and its some applications to rock engineering
- 27 January 2012
- Published by Taylor & Francis
- p. 245-252
Three-dimensional block cutting and its some applications to rock engineering