Kangseop Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kangseop Lee has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Ho-Jin Song
Pohang University of Science and Technology
11 shared publications - Kyunghwan Kim
Samsung Electronics, Hwaseong, South Korea
6 shared publications - Jiseul Kim
Department of Electrical Engineering, Pohang University of Science and Technology, Pohang, South Korea
3 shared publications Seung-Uk Choi
Department of Electrical Engineering, Pohang University of Science and Technology, Pohang, South Korea
3 shared publications- Sirous Bahrami
Pohang University of Science and Technology
3 shared publications Chan-Gyu Choi
School of Electrical Engineering, Pohang University of Science and Technology (POSTECH), Pohang, South Korea
2 shared publications
Latest Publications
- 13 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (6) , 5631-5643
An E-Band Radar Transceiver With Daisy-Chained Wireless Chirp Synchronization for Scalable Multistatic Radar Networks
Recent demonstrations have highlighted that drone swarm Synthetic Aperture Radar (SAR) systems can efficiently cover wide areas while providing enhanced angular diversity for improved ground target information. While frequency-modulated continuous-wave (FMCW) radar systems support both monostatic and multistatic modes, drone-borne radar is typically limited to a monostatic configuration due to significant synchronization challenges. Effective synchronization between transmitters (TXs) and receivers (RXs) is, therefore, essential for multistatic imaging. This work presents a multistatic FMCW radar transceiver (TRX) that uses separate E- and Ka-bands for radar and wireless synchronization, with integrated RF switches enabling conversion between its monostatic and multistatic modes. In multistatic modes, the synchronization chirp signal can be transmitted from the leader to multiple follower modules or relayed by being retransmitted from one follower to another in a daisy-chain configuration. The radar TRX is fabricated in a 28-nm CMOS process, with the chip occupying a total area of 2.88 mm2. The complete module measures $13\times 10.6$ cm and integrates microstrip comb-line antennas for radar with planar Yagi-Uda arrays for synchronization. It achieves a measured EIRP of over 14dBm. Finally, multistatic measurements demonstrated successful target detection up to 35 m, with multistatic tests confirming reliable operation for modules spaced as far as 10 m apart in a daisy-chain configuration.
- 13 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (6) , 5631-5643
An E-Band Radar Transceiver With Daisy-Chained Wireless Chirp Synchronization for Scalable Multistatic Radar Networks
Recent demonstrations have highlighted that drone swarm Synthetic Aperture Radar (SAR) systems can efficiently cover wide areas while providing enhanced angular diversity for improved ground target information. While frequency-modulated continuous-wave (FMCW) radar systems support both monostatic and multistatic modes, drone-borne radar is typically limited to a monostatic configuration due to significant synchronization challenges. Effective synchronization between transmitters (TXs) and receivers (RXs) is, therefore, essential for multistatic imaging. This work presents a multistatic FMCW radar transceiver (TRX) that uses separate E- and Ka-bands for radar and wireless synchronization, with integrated RF switches enabling conversion between its monostatic and multistatic modes. In multistatic modes, the synchronization chirp signal can be transmitted from the leader to multiple follower modules or relayed by being retransmitted from one follower to another in a daisy-chain configuration. The radar TRX is fabricated in a 28-nm CMOS process, with the chip occupying a total area of 2.88 mm2. The complete module measures $13\times 10.6$ cm and integrates microstrip comb-line antennas for radar with planar Yagi-Uda arrays for synchronization. It achieves a measured EIRP of over 14dBm. Finally, multistatic measurements demonstrated successful target detection up to 35 m, with multistatic tests confirming reliable operation for modules spaced as far as 10 m apart in a daisy-chain configuration.
- 23 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (1) , 52-62
A D-Band Phased Array Transmitter With Silicon-Based Resonator Antennas Using FOWLP Technology
This article introduces a D-band phased-array transmitter module that leverages fan-out wafer-level packaging (FOWLP) to integrate multiple RFICs with an antenna-in-package (AiP) architecture. The module integrates a D-band beamforming multiplier chain in 28-nm FD-SOI CMOS and a silicon-based resonator antenna (SRA) array. Four such CMOS-based 160GHz beamforming chains are implemented, each interfaced with a $1 \times 4$ series-fed SRA subarray, yielding a total array aperture of $4.2 \times 4.2$ mm2. To address thermomechanical issues such as package warpage and die misalignment during wafer-level assembly, passive silicon filler dies are strategically placed within the package. The initial die shift of approximately 20 $\mu $ m was effectively reduced to 5.6 $\mu $ m thanks to dummy silicon chips. The implemented array achieves a broadside radiation pattern with a measured peak realized gain of 14.3dBi and an effective isotropic radiated power (EIRP) of 7.1dBm at 160GHz. It supports beam steering over a ±40° range in the elevation plane. The results demonstrate a scalable and thermomechanically reliable solution for high-frequency AiP-based phased arrays, suitable for next-generation communication, radar, and sensing applications.
- 23 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (1) , 52-62
A D-Band Phased Array Transmitter With Silicon-Based Resonator Antennas Using FOWLP Technology
This article introduces a D-band phased-array transmitter module that leverages fan-out wafer-level packaging (FOWLP) to integrate multiple RFICs with an antenna-in-package (AiP) architecture. The module integrates a D-band beamforming multiplier chain in 28-nm FD-SOI CMOS and a silicon-based resonator antenna (SRA) array. Four such CMOS-based 160GHz beamforming chains are implemented, each interfaced with a $1 \times 4$ series-fed SRA subarray, yielding a total array aperture of $4.2 \times 4.2$ mm2. To address thermomechanical issues such as package warpage and die misalignment during wafer-level assembly, passive silicon filler dies are strategically placed within the package. The initial die shift of approximately 20 $\mu $ m was effectively reduced to 5.6 $\mu $ m thanks to dummy silicon chips. The implemented array achieves a broadside radiation pattern with a measured peak realized gain of 14.3dBi and an effective isotropic radiated power (EIRP) of 7.1dBm at 160GHz. It supports beam steering over a ±40° range in the elevation plane. The results demonstrate a scalable and thermomechanically reliable solution for high-frequency AiP-based phased arrays, suitable for next-generation communication, radar, and sensing applications.
- 1 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (10) , 1578-1581
11.3–13.6-GHz Cryo-CMOS 4P4T RF Switch for Superconducting Quantum Computer at mK Temperature
- 1 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (10) , 1578-1581
11.3–13.6-GHz Cryo-CMOS 4P4T RF Switch for Superconducting Quantum Computer at mK Temperature
- 10 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 7, 159-162
248-GHz Subharmonic Mixer Last Transmitter With I/Q Imbalance and LO Feedthrough Calibration
This letter presents a 248 GHz compact direct-conversion transmitter with IQ and LO feedthrough (LOFT) calibration capability, which can achieve a data rate of 20-Gb/s with 16-QAM. The transmitter design incorporates a subharmonic double-balanced mixer configuration, simplifying the complexity of the local oscillator (LO) chain. Furthermore, a Wilkinson power divider and a transmission line terminated by variable capacitors are used to generate LO signals with a 45° phase difference. This configuration, combined with variable gain amplifiers, allows for the precise balancing of IQ amplitude and phase. The measured image rejection ratio and LOFT suppression ratio are better than 25 and 28 dB, respectively, in the range of 242–252 GHz. The DC power consumption of the transmitter is 96.3 mW.
- 10 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 7, 159-162
248-GHz Subharmonic Mixer Last Transmitter With I/Q Imbalance and LO Feedthrough Calibration
This letter presents a 248 GHz compact direct-conversion transmitter with IQ and LO feedthrough (LOFT) calibration capability, which can achieve a data rate of 20-Gb/s with 16-QAM. The transmitter design incorporates a subharmonic double-balanced mixer configuration, simplifying the complexity of the local oscillator (LO) chain. Furthermore, a Wilkinson power divider and a transmission line terminated by variable capacitors are used to generate LO signals with a 45° phase difference. This configuration, combined with variable gain amplifiers, allows for the precise balancing of IQ amplitude and phase. The measured image rejection ratio and LOFT suppression ratio are better than 25 and 28 dB, respectively, in the range of 242–252 GHz. The DC power consumption of the transmitter is 96.3 mW.
- 9 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (4) , 2378-2390
Planar Asymmetric Fed Interdigital Coupling Antenna-in-Package Using FOWLP Process Operating at 60–90 GHz in Endfire Mode
This article first reports a wideband asymmetric fed interdigital coupling antenna (AFICA) with the fan-out wafer-level package (FOWLP) process. The asymmetric fed structure is designed to realize a more compact array size. The interdigital-shaped coupling method between the elements achieves wideband impedance matching with 70- $\Omega$ feeding line. In addition, the exemplified 1 $\times$ 4 AFICA array package demonstrates a wide bandwidth from 60 to 90 GHz and an extremely low profile of 0.044 $\lambda_{{0}}$ at 60 GHz. Furthermore, the prototype module is fabricated and integrated with frequency quadrupler CMOS chip. The measured results exhibit a wide bandwidth from 60 to 90 GHz and a peak gain of 9.3 dBi. The measured antenna efficiency is higher than 80%. Both fabricated package and module feature a wide scanning angle of ${\pm}50^{\circ}$ and low cross-polarization levels ( ${\le}\!-\!18$ dB) at operating bands, respectively. The power-based de-embedding method is proposed to evaluate the performance of real-life modules and systems. The simulated and experimental results of the fan-out (FO) interconnection loss are less than 1 dB, respectively. As a result, the proposed co-planar wideband AFICA array with endfire mode design is fully compatible with various chips, such as 5G/6G communication, radar, and sensing applications.
- 9 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (4) , 2378-2390
Planar Asymmetric Fed Interdigital Coupling Antenna-in-Package Using FOWLP Process Operating at 60–90 GHz in Endfire Mode
This article first reports a wideband asymmetric fed interdigital coupling antenna (AFICA) with the fan-out wafer-level package (FOWLP) process. The asymmetric fed structure is designed to realize a more compact array size. The interdigital-shaped coupling method between the elements achieves wideband impedance matching with 70- $\Omega$ feeding line. In addition, the exemplified 1 $\times$ 4 AFICA array package demonstrates a wide bandwidth from 60 to 90 GHz and an extremely low profile of 0.044 $\lambda_{{0}}$ at 60 GHz. Furthermore, the prototype module is fabricated and integrated with frequency quadrupler CMOS chip. The measured results exhibit a wide bandwidth from 60 to 90 GHz and a peak gain of 9.3 dBi. The measured antenna efficiency is higher than 80%. Both fabricated package and module feature a wide scanning angle of ${\pm}50^{\circ}$ and low cross-polarization levels ( ${\le}\!-\!18$ dB) at operating bands, respectively. The power-based de-embedding method is proposed to evaluate the performance of real-life modules and systems. The simulated and experimental results of the fan-out (FO) interconnection loss are less than 1 dB, respectively. As a result, the proposed co-planar wideband AFICA array with endfire mode design is fully compatible with various chips, such as 5G/6G communication, radar, and sensing applications.
- Open Access
- 15 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 26785-26792
A Tunable D-Band Filter Based on MOSCAP in 65nm CMOS Technology
In this paper, a D-band varactor-based tunable bandpass filter is proposed in 65nm CMOS Technology. The filter is composed of coupled lines loaded with a pair of MOSCAPs that control the passband of the filter. The effects of MOSCAP parameters in terms of the quality factor and the tuning range are studied. The proper placement of the MOSCAP along the resonator is the key parameter to keep insertion loss as low as possible while the tuning range remains intact. A cross-coupled line between input/output ports introduces a pair of transmission zeros and significantly reduces the size of the filter. The tuning range of the proposed structure is 10 % (136 ~ 150 GHz). For this frequency band, the fractional bandwidth (FBW) varies between 10.9 and 11.8 % and the in-band insertion loss is between 4 and 8.2 dB. The overall size of the filter is 0.11λ 0 × 0.095λ 0 . Measurements for the filter show good agreement with the simulation results.
- 15 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 26785-26792
Open AccessA Tunable D-Band Filter Based on MOSCAP in 65nm CMOS Technology
In this paper, a D-band varactor-based tunable bandpass filter is proposed in 65nm CMOS Technology. The filter is composed of coupled lines loaded with a pair of MOSCAPs that control the passband of the filter. The effects of MOSCAP parameters in terms of the quality factor and the tuning range are studied. The proper placement of the MOSCAP along the resonator is the key parameter to keep insertion loss as low as possible while the tuning range remains intact. A cross-coupled line between input/output ports introduces a pair of transmission zeros and significantly reduces the size of the filter. The tuning range of the proposed structure is 10 % (136 ~ 150 GHz). For this frequency band, the fractional bandwidth (FBW) varies between 10.9 and 11.8 % and the in-band insertion loss is between 4 and 8.2 dB. The overall size of the filter is 0.11λ 0 × 0.095λ 0 . Measurements for the filter show good agreement with the simulation results.
- 27 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (5) , 1866-1876
A Broadband D-Band Dual-Peak Gmax-Core Amplifier With a T-Shaped Embedding Network in CMOS
We present a novel high-gain broadband $G_{\mathrm{max}}$ -core amplifier with a T-shaped passive embedding network consisting of two series capacitors and one shunt inductor. The proposed $G_{\mathrm{max}}$ -core has dual-peak properties. By staggering dual-peak $G_{\mathrm{max}}$ -cores, a broad gain–bandwidth amplifier can be achieved with a small number of stages. In addition, the three elements of the T-shaped network give us a high degree of freedom in design. One can design not only the gain profile of the core but also the input and output impedance as desired with the embedding network. In this article, the proposed $G_{\mathrm{max}}$ -core is theoretically analyzed. A three-stage D-band dual-peak $G_{\mathrm{max}}$ -core amplifier is implemented in a 28-nm FDSOI CMOS process to demonstrate the idea. The fabricated amplifier offers a peak small-signal gain and bandwidth of 14.5 dB and 26 GHz (117–143 GHz), respectively, with the power consumption of 21.6 mW. This work shows a reasonable gain–bandwidth product per power dissipation among state-of-the-art amplifiers operating at similar frequencies.
- 27 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (5) , 1866-1876
A Broadband D-Band Dual-Peak Gmax-Core Amplifier With a T-Shaped Embedding Network in CMOS
We present a novel high-gain broadband $G_{\mathrm{max}}$ -core amplifier with a T-shaped passive embedding network consisting of two series capacitors and one shunt inductor. The proposed $G_{\mathrm{max}}$ -core has dual-peak properties. By staggering dual-peak $G_{\mathrm{max}}$ -cores, a broad gain–bandwidth amplifier can be achieved with a small number of stages. In addition, the three elements of the T-shaped network give us a high degree of freedom in design. One can design not only the gain profile of the core but also the input and output impedance as desired with the embedding network. In this article, the proposed $G_{\mathrm{max}}$ -core is theoretically analyzed. A three-stage D-band dual-peak $G_{\mathrm{max}}$ -core amplifier is implemented in a 28-nm FDSOI CMOS process to demonstrate the idea. The fabricated amplifier offers a peak small-signal gain and bandwidth of 14.5 dB and 26 GHz (117–143 GHz), respectively, with the power consumption of 21.6 mW. This work shows a reasonable gain–bandwidth product per power dissipation among state-of-the-art amplifiers operating at similar frequencies.
- 4 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (5) , 1877-1889
Analysis and Design of Multi-Stacked FET Power Amplifier With Phase-Compensation Inductors in Millimeter-Wave Band
Stacked-FET topology is analyzed to increase the output power of a power amplifier (PA) in the millimeter-wave (mm-wave) band. In the mm-wave band, parasitic capacitances of the transistor severely degrade stacking efficiency due to the phase mismatch between stacked FETs. The phase-compensation (PC) inductances, including the losses of the inductor for the best stacking efficiency, are presented in both series and shunt connections. From this analysis, a triple-stacked-FET PA is designed in the $F$ -band. Proper PC series or shunt inductor types are used between the first and second stacked FETs and between the second and third stacked FETs in consideration of the core layout and inductor size. The PA is fabricated in the 28-nm CMOS fully depleted silicon-on-insulator (FD-SOI) process. With a compact core area of 0.054 mm $^{2}$ , the PA achieves peak $P_{\mathrm{SAT}}$ and PAE $_{\mathrm{MAX}}$ of 15.1 dBm and 18.6%, respectively.
- 4 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (5) , 1877-1889
Analysis and Design of Multi-Stacked FET Power Amplifier With Phase-Compensation Inductors in Millimeter-Wave Band
Stacked-FET topology is analyzed to increase the output power of a power amplifier (PA) in the millimeter-wave (mm-wave) band. In the mm-wave band, parasitic capacitances of the transistor severely degrade stacking efficiency due to the phase mismatch between stacked FETs. The phase-compensation (PC) inductances, including the losses of the inductor for the best stacking efficiency, are presented in both series and shunt connections. From this analysis, a triple-stacked-FET PA is designed in the $F$ -band. Proper PC series or shunt inductor types are used between the first and second stacked FETs and between the second and third stacked FETs in consideration of the core layout and inductor size. The PA is fabricated in the 28-nm CMOS fully depleted silicon-on-insulator (FD-SOI) process. With a compact core area of 0.054 mm $^{2}$ , the PA achieves peak $P_{\mathrm{SAT}}$ and PAE $_{\mathrm{MAX}}$ of 15.1 dBm and 18.6%, respectively.
- 8 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 4, 150-153
A 50-Gb/s Compact RadCom E-Band Transmitter With Phase-Controlled Push–Push Quadrupler and Stacked-FET Power Amplifier
We present a 66–79-GHz transmitter (TX) in 40-nm CMOS technology for radar and communication (RadCom) systems. To accommodate the technical requirements for RadCom systems, such as wideband operation with high linearity, a compact TX was implemented with a stacked-FET power amplifier (PA), upconverting passive mixer, and a phase-controlled push–push frequency quadrupler. The TX exhibits OP 1dB and bandwidth of 13.0 dBm and 13 GHz or more, respectively, which are suitable for mid-range sensing up to 100 m with the minimum range resolution of 0.15 m or less and several tens of Gb/s short-range data transmission. In a back-to-back test, the rms error vector magnitude of −21.4 dB was achieved for 50-Gb/s 32-QAM signals occupying 13-GHz bandwidth with an output power of 4 dBm at the PA output. The total core area of the TX is 0.19 mm 2 .
- 8 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 4, 150-153
A 50-Gb/s Compact RadCom E-Band Transmitter With Phase-Controlled Push–Push Quadrupler and Stacked-FET Power Amplifier
We present a 66–79-GHz transmitter (TX) in 40-nm CMOS technology for radar and communication (RadCom) systems. To accommodate the technical requirements for RadCom systems, such as wideband operation with high linearity, a compact TX was implemented with a stacked-FET power amplifier (PA), upconverting passive mixer, and a phase-controlled push–push frequency quadrupler. The TX exhibits OP 1dB and bandwidth of 13.0 dBm and 13 GHz or more, respectively, which are suitable for mid-range sensing up to 100 m with the minimum range resolution of 0.15 m or less and several tens of Gb/s short-range data transmission. In a back-to-back test, the rms error vector magnitude of −21.4 dB was achieved for 50-Gb/s 32-QAM signals occupying 13-GHz bandwidth with an output power of 4 dBm at the PA output. The total core area of the TX is 0.19 mm 2 .
- Open Access
- 29 March 2021
- Published by MDPI AG in Electronics
- Vol. 10 (7) , 804
An E-Band 21-dB Variable-Gain Amplifier with 0.5-V Supply in 40-nm CMOS
This paper presents a variable-gain amplifier (VGA) in the 68–78 GHz range. To reduce DC power consumption, the drain voltage was set to 0.5 V with competitive performance in the gain and the noise figure. High-Q shunt capacitors were employed at the gate terminal of the core transistors to move input matching points for easy matching with a compact transformer. The four stages amplifier fabricated in 40-nm bulk complementary metal oxide semiconductor (CMOS) showed a peak gain of 24.5 dB at 71.3 GHz and 3‑dB bandwidth of more than 10 GHz in 68–78 GHz range with approximately 4.8-mW power consumption per stage. Gate-bias control of the second stage in which feedback capacitances were neutralized with cross-coupled capacitors allowed us to vary the gain by around 21 dB in the operating frequency band. The noise figure was estimated to be better than 5.9 dB in the operating frequency band from the full electromagnetic (EM) simulation.
- 29 March 2021
- Published by MDPI AG in Electronics
- Vol. 10 (7) , 804
Open AccessAn E-Band 21-dB Variable-Gain Amplifier with 0.5-V Supply in 40-nm CMOS
This paper presents a variable-gain amplifier (VGA) in the 68–78 GHz range. To reduce DC power consumption, the drain voltage was set to 0.5 V with competitive performance in the gain and the noise figure. High-Q shunt capacitors were employed at the gate terminal of the core transistors to move input matching points for easy matching with a compact transformer. The four stages amplifier fabricated in 40-nm bulk complementary metal oxide semiconductor (CMOS) showed a peak gain of 24.5 dB at 71.3 GHz and 3‑dB bandwidth of more than 10 GHz in 68–78 GHz range with approximately 4.8-mW power consumption per stage. Gate-bias control of the second stage in which feedback capacitances were neutralized with cross-coupled capacitors allowed us to vary the gain by around 21 dB in the operating frequency band. The noise figure was estimated to be better than 5.9 dB in the operating frequency band from the full electromagnetic (EM) simulation.