Lin Su
Lin Su has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Chongjian Cao
Key Laboratory of High Performance Polymer Materials & Technology of Ministry of Education, School of Chemistry and Chemical Engineering, Nanjing University, Nanjing 210023, China
1 shared publication - Dongliang Pei
China Shipbuilding Corporation System Engineering Research Institute, Beijing 100080, China
1 shared publication - Hao Song
Systems Engineering Research Institute, Beijing 100036, China
1 shared publication - Hongfeng Xie
MOE Key Laboratory of High Performance Polymer Materials and Technology, School of Chemistry and Chemical Engineering, Nanjing University, Nanjing 210023, China
1 shared publication - Junqi Shi
Key Laboratory of High Performance Polymer Materials & Technology of Ministry of Education, School of Chemistry and Chemical Engineering, Nanjing University, Nanjing 210023, China
1 shared publication - Qingjun Wang
MOE Key Laboratory of High Performance Polymer Materials and Technology, School of Chemistry and Chemical Engineering, Nanjing University, Nanjing 210023, China
1 shared publication
Latest Publications
- Open Access
- 18 February 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (4) , 2152
The Construction and Investigation of Two-Dimensional Re-Entrant Multiphase Honeycomb Lattice Metafluid
Compared to conventional materials, underwater metamaterials possess numerous advantages in the manipulation of sound waves, which have garnered increasing attention. In terms of composition, commonly studied underwater wideband metamaterials can be classified into solid-phase pentamode metafluid and water–solid coupling metafluid. The concept of multiphase design in pentamode metafluid allows for decoupling the regulation of equivalent density from that of the equivalent bulk modulus, facilitating more convenient structural design. In typical auxetic metamaterial structure designs, the “re-entrant” mechanism is commonly employed; the skeleton is inwardly bent to a certain extent, enabling the design of a low volume-modulus for each cell. Consequently, a novel type of water–solid coupling metafluid is devised by combining the concepts of “multiphase” and “re-entrant”. Firstly, a straight-sided skeleton (referred to as “ss” skeletal) unit cell is designed, and its compression wave frequency band is determined through analysis of its band characteristics and related vibration modes. Subsequently, the “re-entrant” (referred to as “re”) mechanism is introduced into a unit cell, revealing an increase in equivalent density while decreasing the equivalent volume modulus due to this feature. The bent skeleton provides lower bulk modulus, while multiphase (referred to as “mp”) counterweighting offers higher equivalent density; their combination enables designing more impedance-matched metafluid. Then, a unit cell is designed utilizing both “re” and “mp” characteristics. Finally, acoustic performance simulations and analyses verify that both types exhibit excellent broadband water-like properties within the frequency range of 5000–27,000 Hz. In order to further validate the reliability of the design concept, two pairs of underwater metafluid cells with an impedance-matching effect were subsequently developed, demonstrating sound speeds that are half and one-third that of water, respectively. The skeleton thickness of the “re” cell was moderately enhanced compared to that of the straight side cell, thereby presenting an innovative approach for designing robust underwater metafluid cells.
- 18 February 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (4) , 2152
Open AccessThe Construction and Investigation of Two-Dimensional Re-Entrant Multiphase Honeycomb Lattice Metafluid
Compared to conventional materials, underwater metamaterials possess numerous advantages in the manipulation of sound waves, which have garnered increasing attention. In terms of composition, commonly studied underwater wideband metamaterials can be classified into solid-phase pentamode metafluid and water–solid coupling metafluid. The concept of multiphase design in pentamode metafluid allows for decoupling the regulation of equivalent density from that of the equivalent bulk modulus, facilitating more convenient structural design. In typical auxetic metamaterial structure designs, the “re-entrant” mechanism is commonly employed; the skeleton is inwardly bent to a certain extent, enabling the design of a low volume-modulus for each cell. Consequently, a novel type of water–solid coupling metafluid is devised by combining the concepts of “multiphase” and “re-entrant”. Firstly, a straight-sided skeleton (referred to as “ss” skeletal) unit cell is designed, and its compression wave frequency band is determined through analysis of its band characteristics and related vibration modes. Subsequently, the “re-entrant” (referred to as “re”) mechanism is introduced into a unit cell, revealing an increase in equivalent density while decreasing the equivalent volume modulus due to this feature. The bent skeleton provides lower bulk modulus, while multiphase (referred to as “mp”) counterweighting offers higher equivalent density; their combination enables designing more impedance-matched metafluid. Then, a unit cell is designed utilizing both “re” and “mp” characteristics. Finally, acoustic performance simulations and analyses verify that both types exhibit excellent broadband water-like properties within the frequency range of 5000–27,000 Hz. In order to further validate the reliability of the design concept, two pairs of underwater metafluid cells with an impedance-matching effect were subsequently developed, demonstrating sound speeds that are half and one-third that of water, respectively. The skeleton thickness of the “re” cell was moderately enhanced compared to that of the straight side cell, thereby presenting an innovative approach for designing robust underwater metafluid cells.
- Open Access
Designing Self-Sustainable Icephobic Layer by Introducing a Lubricating Un-Freezable Water Hydrogel from Sodium Polyacrylate on the Polyolefin Surface
A convenient, environment-friendly, and cost-effective method to keep anti-icing for a long time was highly desirable. Slippery lubricant layers were regarded to be effective and promising for anti-icing on different surfaces, but the drought-out of lubricants and the possible detriments to the environment were inevitable. By combining super-high molecular weight sodium polyacrylate (H-PAAS) with polyolefin through a one-pot method, a self-sustainable lubricating layer with extremely low ice adhesion of un-freezable water hydrogel was achieved at subzero conditions. The lubricant hydrogel layer could auto-spread and cover the surface of polyolefin after encountering supercooled water, frost, or ice. Due to the reduction of storage modulus in the interface, the ice adhesion of the specimen surfaces was far below 20 kPa, varying from 5.13 kPa to 18.95 kPa. Furthermore, the surfaces could preserve the fairly low adhesion after icing/de-icing cycles for over 15 times and thus exhibited sustainable durability. More importantly, this method could be introducing to various polymers and is of great promise for practical applications.
Open AccessDesigning Self-Sustainable Icephobic Layer by Introducing a Lubricating Un-Freezable Water Hydrogel from Sodium Polyacrylate on the Polyolefin Surface
A convenient, environment-friendly, and cost-effective method to keep anti-icing for a long time was highly desirable. Slippery lubricant layers were regarded to be effective and promising for anti-icing on different surfaces, but the drought-out of lubricants and the possible detriments to the environment were inevitable. By combining super-high molecular weight sodium polyacrylate (H-PAAS) with polyolefin through a one-pot method, a self-sustainable lubricating layer with extremely low ice adhesion of un-freezable water hydrogel was achieved at subzero conditions. The lubricant hydrogel layer could auto-spread and cover the surface of polyolefin after encountering supercooled water, frost, or ice. Due to the reduction of storage modulus in the interface, the ice adhesion of the specimen surfaces was far below 20 kPa, varying from 5.13 kPa to 18.95 kPa. Furthermore, the surfaces could preserve the fairly low adhesion after icing/de-icing cycles for over 15 times and thus exhibited sustainable durability. More importantly, this method could be introducing to various polymers and is of great promise for practical applications.