Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Walter Vera-Tudela has a total of 58 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Experimental study of lube oil pre-ignition in an optical gas engine test rig

    by Walter Vera-Tudela, Pascal Süess, Patrick Albrecht, Silas Wüthrich, Kai Herrmann

    Lean-premixed gas combustion is an attractive option for meeting future emission standards toward considerably lower particulate matter and emissions while obtaining an efficiency comparable to diesel combustion. However, ignition processes still pose considerable challenges, with pre-ignition being a major issue. The pre-ignition phenomenon might result from the self-ignition of lube oil in hot zones, making it challenging to observe in real engines. To study single or sparsely separated lube oil droplets under engine-like conditions, the “Flex-OeCoS” experimental test facility was used. To be able to induce such pre-ignitions artificially a novel piezo droplet injector was developed and manufactured, which enabled the metering of minor amounts of lubricating oil or even the injection of single droplets. High-speed cameras and specially developed and partially automatable and adaptive evaluation algorithms were used to record and track the behavior of the injected droplet using overlaid schlieren and OH* chemiluminescence. During the measurement campaigns, relevant operating parameters were varied, and optical investigations were carried out with an ignitable mixture on the Flex-OeCoS test facility under engine-relevant operating conditions. Spontaneous ignition of the vaporized lubricating oil was observed, which subsequently led to ignition of the whole air-fuel mixture in the optical combustion chamber. This was especially evident for lean methane-air mixtures up to an air-fuel ratio of 2.0. With this approach, information could be gathered about the necessary internal engine conditions that lead to pre-ignition in lean mixtures and where their limits lie.


  • Open Access

    Investigation of Flow Fields Emanating from Two Parallel Inlet Valves Using LES, PIV, and POD

    by Jana Hoffmann, Walter Vera-Tudela, Niklas Mirsch, Dario Wüthrich, Bruno Schneider, Marco Günther, Stefan Pischinger, Daniel A. Weiss, Kai Herrmann

    Understanding cycle-to-cycle variations (CCV) is of practical importance for the combustion of fossil and renewable fuels, as increasingly stringent emission regulations require reductions in the negative effects of such variations. The subject of this study is the flow around inlet valves, since oscillations of such inlet flows affect the flow structure in the cylinder and are thus one of the causes of CCV. To this end, a parametric analysis of the influences of the mass flow rate and valve lift of two parallel engine intake valves on the flow structures is performed. This follows on from an earlier similar study where the flow around a single intake valve was investigated. To analyse the flow behaviour and, in particular, the interactions of the flow leaving these two valves, an optical test rig for 2D particle image velocimetry (PIV) and a large eddy simulation (LES) are used. Proper orthogonal decomposition (POD), together with a quadruple decomposition and the Reynolds stress transport equations, are used to study the turbulence phenomena. The PIV and LES results are in good agreement with each other. The detailed LES analysis of the flow structures shows that, for small valve lifts, the flow separates along the whole perimeter of the intake valve, and for larger valve lifts, the flow escapes only to one side. This is, for combustion engines with the tumble concept, the stage at which the tumble movement develops. Moreover, the flow structures are strongly influenced by the valve lift, while they are unaffected by the variation in the mass flow. The turbulent kinetic energy in the flow field increases quadratically with a decreasing valve lift and increasing mass flow. The large, high-energetic flow structures are particularly dominant near the jet, and the small, low-energetic structures are homogeneously distributed within the flow field. The specific Reynolds stress transport equation shows the limitations of two-dimensionality and large timesteps in the PIV results and the limitations of the LES model.


  • Open Access

    Flow Field Investigation of a Single Engine Valve Using PIV, POD, and LES

    by Jana Hoffmann, Niklas Mirsch, Walter Vera-Tudela, Dario Wüthrich, Jorim Rosenberg, Marco Günther, Stefan Pischinger, Daniel A. Weiss, Kai Herrmann

    Due to stringent emission regulations, it is of practical significance to understand cycle-to-cycle variations in the combustion of fossil or renewable fuels to reach future emission regulations. The present study aims to conduct a parametric investigation to analyse the influence of the valve lift and different mass flows of an inlet valve of the test engine “Flex-OeCoS” on the flow structures. To gain a deeper understanding of the flow behaviour, an optical test bench for 2D Particle Image Velocimetry (PIV) and a Large Eddy Simulation (LES) are used. Turbulence phenomena are investigated using Proper Orthogonal Decomposition (POD) with a quadruple decomposition and the Reynolds stress transport equation. The results show good agreement between the PIV and LES. Moreover, the main flow structures are primarily affected by valve lift while being unaffected by mass flow variation. The turbulent kinetic energy within the flow field increases quadratically to the mass flow and to the decreasing valve lift, where large high-energetic flow structures are observed in the vicinity of the jet and small low-energetic structures are homogeneously distributed within the flow field. Furthermore, the convective flux, the turbulent diffusive flux, the rate of change, and the production of specific Reynolds stress are the dominant terms within the specific Reynolds stress transport equation.


  • Study on the ignitability of a high-pressure direct-injected methane jet using a scavenged pre-chamber under a wide range of conditions

    by Walter Vera-Tudela, Bruno Schneider, Silas Wüthrich, Kai Herrmann

    Natural gas is a promising alternative fuel for internal combustion engines, it allows for a reduction of engine-out emissions without impairing high engine efficiencies. Although this approach is already utilized from small to large engine classes, it is almost exclusively based on the combustion of a premixed homogeneous charge. For ignition, small engines use standard spark plugs or pre-chambers, while large and lean-operated engines use pre-chambers and pilot injections. Direct high-pressure gas injection is a more recent, alternative way to operate gas engines which offers benefits compared to premixed operation such as high combustion pressures, leaner operation, easier quantity regulation, and higher compression ratios, among others. However, in contrast to diesel injection, the compression temperatures are too low for the auto-ignition of the gas jets. Therefore, an additional ignition system is required, usually a pilot injection system is used. In this study, the usability and performance of a scavenged pre-chamber used for the ignition a high-pressure gas jet has been investigated in an optically accessible test-rig that is able to operate at engine-like conditions. Results show that the turbulent hot jet generated by the pre-chamber was able to ignite the high-pressure gas jet under a wide range of operating conditions. Moreover, it also appears to be a promising ignition strategy for very early direct injection during the compression stroke as well as for port injection. The good performance is attributed to the intense mixing of the main gas jet with the hot jet exiting the pre-chamber.


  • Open Access

    Experimental Study of the Lean Combustion Behaviour for Methane and Hydrogen Under Different Oxygen Concentrations in an Optical Pre-Chamber

    by Walter Vera-Tudela, Alba Garcia-Carrero, Jose Pastor, Konstantinos Boulouchos

    In the transportation industry, the use of alternative fuels as well as the implementation of new combustion strategies have a main role for its development. In this study, both strategies have been combined with the aim to determine the limits of lean combustion under different oxygen concentrations. The study of Turbulent Jet Ignition (TJI) has been carried out in an optical pre-chamber (OPC) which has optical accesses both in the pre-chamber (PC) and in the main chamber (MC). Therefore, the whole combustion process can be characterized using methane and hydrogen. Their combustion behaviour has been studied by analysing highspeed images, pressure traces, and pressure derivative data. Intake conditions such as temperature and pressure were kept constant, while oxygen concentration and the equivalence ratio Φ (dilution fraction) were swept. It was found that methane operates in a shorter lean combustion range and the variations in oxygen concentration affect considerably its combustion behaviour. In many cases, misfiring occurred, while on other cases, when methane combustion took place, quenching was observed. Conversely, hydrogen was not significantly affected with the oxygen concentration sweep. This fuel (H2) can operate under ultra-lean conditions (0.35<Φ<1). Furthermore, hydrogen demonstrated higher combustion propagation and therefore, the combustion duration was the shortest. Therefore, hydrogen could be used as a combustion enhancing fuel even in the cases where high levels of Exhaust Gas Recirculation (EGR) strategies are implemented.

  • Study on the ignitability of a high-pressure direct-injected methane jet using a diesel pilot, a glow-plug, and a pre-chamber

    by Walter Vera-Tudela, Bruno Schneider, Silas Wüthrich, Kai Herrmann

    Natural gas is a promising alternative fuel for internal combustion engines, it allows for a reduction of engine-out emissions without impairing high engine efficiencies. Although this approach is already utilized from small to large engine classes, it is almost exclusively based on the combustion of a premixed, homogeneous charge. For ignition, small engines use standard spark-plugs or pre-chambers, while large and lean-operated engines use pre-chambers and pilot injections. Direct high-pressure gas injection is a more recent, alternative way to operate gas engines which offers benefits compared to premixed operation such as high compression ratio, high combustion pressures, lean operation, quantity regulation, among others. However, in contrast to diesel direct injection, the compression temperatures are too low for the auto-ignition of the gas jets. Therefore, an additional ignition system is required, usually a pilot injection system is used. In this study, the usability and performance of three ignition strategies for direct injected high-pressure gas jets have been investigated in an optically accessible test-rig that is able to operate at engine-like conditions. The first type of ignition system is a pilot injection with a liquid fuel, the second is a glow-plug located near the main gas jet, and the third system is a pre-chamber with a nozzle hole aimed at the main gas jet. Results show that all three strategies are feasible options under the studied conditions. Ignition by a pilot fuel injection is a safe and reliable way to ignite the main fuel. The glow-plug is less reliable and leads to high cycle-to-cycle variation. The best option in the present study is the pre-chamber, it is very reliable, delivers the highest peak cylinder pressure and exhibits the lowest cyclic variability. The good performance is attributed to the intense mixing of the main gas jet with the hot jet exiting the pre-chamber.


  • Investigations on spark pre-chamber ignition and subsequent turbulent jet main chamber ignition in a novel optically accessible test rig

    by Walter Vera-Tudela, Christophe Barro, Konstantinos Boulouchos

    Turbulent jet ignition (TJI) is a promising strategy to ignite diluted air-fuel mixtures; this is usually generated by igniting a fraction of the mixture inside a small pre-chamber. Nevertheless, the processes that take place inside the pre-chamber, as well as the injection of the turbulent jet into the main chamber and its subsequent re-ignition are not fully understood. The current work presents an experimental investigation that studies the effects of the nozzle size, turbulence level, and air-fuel mixture on the pre-chamber ignition and main chamber re-ignition and combustion. To accomplish this, a series of experiments have been carried out under different boundary conditions. To understand the phenomena taking place in the pre- and main chamber, two different approaches were taken: On one hand, (1) pressure-based diagnostics were applied by fitting a pressure sensor in each of the chambers. This was done to trace the pressure evolution during the whole combustion event and to calculate the heat-release. On the other hand, (2) optical diagnostics were setup on both combustion chambers, using dual schlieren setups synchronized at the same frame rate. The optically accessible test rig and the combination of schlieren in the pre-chamber (PC) & main-chamber (MC) allows to visualize the ignition, flame propagation, quenching mechanisms and re-ignition under a wide range of boundary conditions. This combined with the pressure traces and heat-release give a full understanding of the ignition and combustion processes. Higher turbulence levels and equivalence ratios increase the propagation of the flame front and the peak pressure in the pre-chamber. The resulting higher nozzle-exit velocities lead, on one hand, to faster mixing and therefore to a larger portion of main chamber fuel within the jet, which decrease the main chamber combustion duration. On the other hand, to high quenching and longer re-ignition times, which show the adverse effect.


  • Open Access

    Numerical investigation of the autoignition of underexpanded methane jets

    by V.D. Sakellarakis, Y.M. Wright, W. Vera-Tudela, K. Boulouchos


  • Experimental investigation of wall heat transfer due to spray combustion in a high-pressure/high-temperature vessel

    by Karri Keskinen, Walter Vera-Tudela, Yuri M Wright, Konstantinos Boulouchos

    Combustion chamber wall heat transfer is a major contributor to efficiency losses in diesel engines. In this context, thermal swing materials (adapting to the surrounding gas temperature) have been pinpointed as a promising mitigative solution. In this study, experiments are carried out in a high-pressure/high-temperature vessel to (a) characterise the wall heat transfer process ensuing from wall impingement of a combusting fuel spray, and (b) evaluate insulative improvements provided by a coating that promotes thermal swing. The baseline experimental condition resembles that of Spray A from the Engine Combustion Network, while additional variations are generated by modifying the ambient temperature as well as the injection pressure and duration. Wall heat transfer and wall temperature measurements are time-resolved and accompanied by concurrent high-speed imaging of natural luminosity. An investigation with an uncoated wall is carried out with several sensor locations around the stagnation point, elucidating sensor-to-sensor variability and setup symmetry. Surface heat flux follows three phases: (i) an initial peak, (ii) a slightly lower plateau dependent on the injection duration, and (iii) a slow decline. In addition to the uncoated reference case, the investigation involves a coating made of porous zirconia, an established thermal swing material. With a coated setup, the projection of surface quantities (heat flux and temperature) from the immersed measurement location requires additional numerical analysis of conjugate heat transfer. Starting from the traces measured beneath the coating, the surface quantities are obtained by solving a one-dimensional inverse heat transfer problem. The present measurements are complemented by CFD simulations supplemented with recent rough-wall models. The surface roughness of the coated specimen is indicated to have a significant impact on the wall heat flux, offsetting the expected benefit from the thermal swing material.