Alper Karakoca
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Alper Karakoca has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Serdar Osman Yilmaz
Mechanical Engineering, Tekirdag Namik Kemal University, Tekirdag, Turkey
2 shared publicationsSerdar Osman Yılmaz
Faculty of Engineering, Department of Mechanical Engineering , 162334 Tekirdag Namik Kemal University , 59000 , Çorlu-Tekirdag , Türkiye
2 shared publications- Ahmet Cihan
Beykent Üniversitesi
1 shared publication - Kamil Kahveci
Trakya University
1 shared publication - Rafayel Shaliyev
Civil Engineering Department, Çorlu Faculty of Engineering, Tekirdağ Namık Kemal University, Çorlu/Tekirdağ, Turkey
1 shared publication Sercan Kavak
Tekirdağ Namık Kemal University , Faculty of Engineering , Department of Mechanical Engineering , 59160 , Çorlu , Tekirdağ , Türkiye
1 shared publication
Latest Publications
- 10 December 2025
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 79 (1) , 5
Experimental and Statistical Investigation of Mechanical Properties in Sand Casting A360 Alloy
- 10 December 2025
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 79 (1) , 5
Experimental and Statistical Investigation of Mechanical Properties in Sand Casting A360 Alloy
- 23 January 2025
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 67 (3) , 561-567
Fabrication and wear performance of M7C3 carbide reinforced epoxy composites
The role of materials in industrial engineering has become even more important today. Various methods are used to develop materials with desired properties. Cr7C3 carbide and grease oil reinforced epoxy-based matrix composites were produced. Microscopic analysis of the composites was carried out by SEM. The differences in the wear properties of the composites were investigated in dry sliding wear test. Increasing sliding speed and load increased the wear of the composites. Combining Cr7C3 with epoxy resulted in improved wear performance. The higher the chromium carbide level increased the coefficient of friction. The best wear resistance result was obtained from 75 wt.% chromium carbide reinforced composite. The change in wear resistance varied significantly depending on the epoxy resin ratio and the amount of reinforcement.
- 23 January 2025
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 67 (3) , 561-567
Fabrication and wear performance of M7C3 carbide reinforced epoxy composites
The role of materials in industrial engineering has become even more important today. Various methods are used to develop materials with desired properties. Cr7C3 carbide and grease oil reinforced epoxy-based matrix composites were produced. Microscopic analysis of the composites was carried out by SEM. The differences in the wear properties of the composites were investigated in dry sliding wear test. Increasing sliding speed and load increased the wear of the composites. Combining Cr7C3 with epoxy resulted in improved wear performance. The higher the chromium carbide level increased the coefficient of friction. The best wear resistance result was obtained from 75 wt.% chromium carbide reinforced composite. The change in wear resistance varied significantly depending on the epoxy resin ratio and the amount of reinforcement.
- 16 December 2024
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 67 (1) , 136-146
Enhanced mechanical properties of Sr-modified Al–Mg–Si alloy by thermo-mechanical treatment
In this study, the effect of thermomechanical treatments applied to strontium-modified A360 alloy on the microstructure and mechanical properties of the alloy was investigated. Optical microscopy, XRD, and SEM were employed to examine the microstructural properties, while tensile and hardness tests were conducted on the samples to evaluate the mechanical properties. It was observed that the strength values increased as the deformation amount increased, and subsequently, optimum conditions (tensile strength and ductility) were determined after the subsequent aging treatment. Following cold deformation, dendritic structure shifted towards the direction of deformation along with the eutectic silicon structure. After aging, it was found that the dendritic structure transformed into equiaxed grains at certain temperature. The highest tensile strength of 383 MPa was achieved in the sample with a deformation amount of 70 %. In this case, the ductility value was 2.85 %. Subsequently, the optimum conditions after aging were determined as 160 °C & 4 h, resulting in a tensile strength of 341 MPa and ductility of 3.62 %.
- 16 December 2024
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 67 (1) , 136-146
Enhanced mechanical properties of Sr-modified Al–Mg–Si alloy by thermo-mechanical treatment
In this study, the effect of thermomechanical treatments applied to strontium-modified A360 alloy on the microstructure and mechanical properties of the alloy was investigated. Optical microscopy, XRD, and SEM were employed to examine the microstructural properties, while tensile and hardness tests were conducted on the samples to evaluate the mechanical properties. It was observed that the strength values increased as the deformation amount increased, and subsequently, optimum conditions (tensile strength and ductility) were determined after the subsequent aging treatment. Following cold deformation, dendritic structure shifted towards the direction of deformation along with the eutectic silicon structure. After aging, it was found that the dendritic structure transformed into equiaxed grains at certain temperature. The highest tensile strength of 383 MPa was achieved in the sample with a deformation amount of 70 %. In this case, the ductility value was 2.85 %. Subsequently, the optimum conditions after aging were determined as 160 °C & 4 h, resulting in a tensile strength of 341 MPa and ductility of 3.62 %.
- 2 April 2021
- Published by Taylor & Francis in The Journal of the Textile Institute
- Vol. 113 (5) , 769-778
A mathematical model for through-air drying process of yarn bobbins
In this study, a mathematical model has been developed to simulate the through-air drying process of yarn bobbins. For this purpose, experimental data was obtained in a prototype experimental set up by passing pressurized hot air through the wool yarn bobbins. First of all, the physical phenomenon expressing the drying process has been reduced to the heat transfer problem and then a mathematical model has been written for the drying process which also includes the convective term. Using the experimental data, the coefficient included in the mathematical model was found by the extremal method. So, an inverse problem was solved. The accuracy of the model was checked by comparing with the experimentally obtained temperature values after solving a direct heat transfer problem in the given conditions. Good correlation between the obtained model results and the experimental results shows the accuracy of the mathematical model.
- 2 April 2021
- Published by Taylor & Francis in The Journal of the Textile Institute
- Vol. 113 (5) , 769-778
A mathematical model for through-air drying process of yarn bobbins
In this study, a mathematical model has been developed to simulate the through-air drying process of yarn bobbins. For this purpose, experimental data was obtained in a prototype experimental set up by passing pressurized hot air through the wool yarn bobbins. First of all, the physical phenomenon expressing the drying process has been reduced to the heat transfer problem and then a mathematical model has been written for the drying process which also includes the convective term. Using the experimental data, the coefficient included in the mathematical model was found by the extremal method. So, an inverse problem was solved. The accuracy of the model was checked by comparing with the experimentally obtained temperature values after solving a direct heat transfer problem in the given conditions. Good correlation between the obtained model results and the experimental results shows the accuracy of the mathematical model.