Tirtha Roy-Biswas
Research Subjects
Tirtha Roy-Biswas has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Dhrubajyoti Sen
Indian Institute of Technology Kharagpur
3 shared publications - Pankaj Singh
Indian Institute of Technology Kharagpur
2 shared publications - Dhrubajyoti Sen
Department of Civil Engineering, Indian Institute of Technology Kharagpur, Kharagpur, India
1 shared publication - Sazeda Begam
University of Nottingham
1 shared publication - Subhasish Dey
Indian Institute of Technology Gandhinagar
1 shared publication
Latest Publications
- 23 October 2026
- Published by Taylor & Francis in Journal of Hydraulic Research
- p. 1-19
Comparative two-dimensional and three-dimensional numerical analysis of steady flow through a levee breach
1 Levees are structures built along riverbanks to protect the adjoining areas from flooding. Consequently, the failure of levees constitutes one of the major reasons for flooding worldwide (Van Eme...
- 23 October 2026
- Published by Taylor & Francis in Journal of Hydraulic Research
- p. 1-19
Comparative two-dimensional and three-dimensional numerical analysis of steady flow through a levee breach
1 Levees are structures built along riverbanks to protect the adjoining areas from flooding. Consequently, the failure of levees constitutes one of the major reasons for flooding worldwide (Van Eme...
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
Volume of fluid approach for modeling nappe flow over hydraulic structures
Accurate simulation of the air–water interface of the overflowing sheet of water in weirs, referred to as nappe, is a challenging prospect from a computational fluid dynamics (CFD) modeling point of view. This study presents a systematic analysis of the widely used interface-capturing volume of fluid (VOF) technique for simulating nappe profiles, which has not received adequate attention in existing literature. Popular CFD codes employ the partial VOF (pVOF) method, which solves for a combined air–water flow and demarcates the free surface using an advection equation for the VOF function. The study finds that the coupled Reynolds-averaged Navier–Stokes (RANS)-pVOF model performs poorly in capturing non-aerated nappe flows. Moreover, the study shows that the choice of the turbulence closure model adopted has a negligible impact on the pVOF model outcome. Conversely, the study demonstrates that the original VOF approach, called TruVOF, which computes the flow only in the liquid regions, precisely simulates the nappe flow structure. The model performances are validated using the water level, velocity, and pressure distribution data from laboratory observations from a wide range of experiments conducted using weirs with square edged or rounded entrance. In addition, the study thoroughly examines the laminar modeling approach for simulating the nappe flow characteristics. This study demonstrates that the coupled laminar-TruVOF approach produces results that are at par with the RANS-TruVOF approach and presents a computationally inexpensive yet precise numerical tool for estimating the critical nappe flow characteristics and may be efficiently used to analyze the head-discharge characteristics of weirs.
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
Volume of fluid approach for modeling nappe flow over hydraulic structures
Accurate simulation of the air–water interface of the overflowing sheet of water in weirs, referred to as nappe, is a challenging prospect from a computational fluid dynamics (CFD) modeling point of view. This study presents a systematic analysis of the widely used interface-capturing volume of fluid (VOF) technique for simulating nappe profiles, which has not received adequate attention in existing literature. Popular CFD codes employ the partial VOF (pVOF) method, which solves for a combined air–water flow and demarcates the free surface using an advection equation for the VOF function. The study finds that the coupled Reynolds-averaged Navier–Stokes (RANS)-pVOF model performs poorly in capturing non-aerated nappe flows. Moreover, the study shows that the choice of the turbulence closure model adopted has a negligible impact on the pVOF model outcome. Conversely, the study demonstrates that the original VOF approach, called TruVOF, which computes the flow only in the liquid regions, precisely simulates the nappe flow structure. The model performances are validated using the water level, velocity, and pressure distribution data from laboratory observations from a wide range of experiments conducted using weirs with square edged or rounded entrance. In addition, the study thoroughly examines the laminar modeling approach for simulating the nappe flow characteristics. This study demonstrates that the coupled laminar-TruVOF approach produces results that are at par with the RANS-TruVOF approach and presents a computationally inexpensive yet precise numerical tool for estimating the critical nappe flow characteristics and may be efficiently used to analyze the head-discharge characteristics of weirs.
- 1 January 2023
- Published by American Society of Civil Engineers (ASCE) in Journal of Waterway, Port, Coastal, and Ocean Engineering
- Vol. 149 (1) , 05022005
Tidal Bore Dynamics of a Mixed Estuary: The Hooghly River, India
The study establishes, with the aid of field measurements and numerical modeling, that the upper reach of the Hooghly estuary (India), though damped, registers an intense tidal bore. The lower estuary is amplified but does not show signs of bore formation. Limited quantitative studies are available on bores forming in damped estuaries. This study attempts to fill this gap using tidal gauge and velocity observations supplemented with simulation results obtained using the open-source numerical shallow-water solver TELEMAC 2D. New estimates of bore intensity in the Hooghly are presented confirming that the bore Froude number may reach 1.37 in the upper estuary for higher tidal ranges. The numerical model is used to gain further insights into the formation and evolution of the Hooghly bore. The model, despite using a vertically averaged velocity field, simulates tidal wave propagation and estimates of velocity magnitude during bore propagation with significant accuracy. The study demonstrates that the proposed model is an efficient and inexpensive tool for capturing the bore phenomenon and may be used to supplement field observations. Using the simulation results, key features of the Hooghly bore, such as the distance of the bore inception from the ocean mouth and the threshold tidal range for bore formation are investigated. The numerical simulations highlight the impact of riverbed asymmetry in bore appearances in natural estuaries. The analysis also reveals new information about bores in the Hooghly estuary, which may be useful for planning shipping and berthing operations in the port terminals along the river. A comparison with other estuaries witnessing tidal bores indicates that the Hooghly experiences a strong bore, despite the high dissipative forces owing to the rapid convergence of river width.
- 1 January 2023
- Published by American Society of Civil Engineers (ASCE) in Journal of Waterway, Port, Coastal, and Ocean Engineering
- Vol. 149 (1) , 05022005
Tidal Bore Dynamics of a Mixed Estuary: The Hooghly River, India
The study establishes, with the aid of field measurements and numerical modeling, that the upper reach of the Hooghly estuary (India), though damped, registers an intense tidal bore. The lower estuary is amplified but does not show signs of bore formation. Limited quantitative studies are available on bores forming in damped estuaries. This study attempts to fill this gap using tidal gauge and velocity observations supplemented with simulation results obtained using the open-source numerical shallow-water solver TELEMAC 2D. New estimates of bore intensity in the Hooghly are presented confirming that the bore Froude number may reach 1.37 in the upper estuary for higher tidal ranges. The numerical model is used to gain further insights into the formation and evolution of the Hooghly bore. The model, despite using a vertically averaged velocity field, simulates tidal wave propagation and estimates of velocity magnitude during bore propagation with significant accuracy. The study demonstrates that the proposed model is an efficient and inexpensive tool for capturing the bore phenomenon and may be used to supplement field observations. Using the simulation results, key features of the Hooghly bore, such as the distance of the bore inception from the ocean mouth and the threshold tidal range for bore formation are investigated. The numerical simulations highlight the impact of riverbed asymmetry in bore appearances in natural estuaries. The analysis also reveals new information about bores in the Hooghly estuary, which may be useful for planning shipping and berthing operations in the port terminals along the river. A comparison with other estuaries witnessing tidal bores indicates that the Hooghly experiences a strong bore, despite the high dissipative forces owing to the rapid convergence of river width.
- 22 July 2022
- Published by Springer Nature in Environmental Fluid Mechanics
- Vol. 22 (6) , 1253-1281
Critical analysis of turbulence models for simulating positive surge waves in open channels in a RANS-VOF setup
- 22 July 2022
- Published by Springer Nature in Environmental Fluid Mechanics
- Vol. 22 (6) , 1253-1281
Critical analysis of turbulence models for simulating positive surge waves in open channels in a RANS-VOF setup
- 1 December 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Irrigation and Drainage Engineering
- Vol. 147 (12) , 04021058
Submerged Flow over Barrage Weirs: A Computational Fluid Dynamics Model Study
Barrage weirs, which are trapezoidal-sectioned sharp-crested weirs having finite crest length, are primarily used in the Indian subcontinent for diverting water for irrigation. This study presents an investigative study on submerged flows over barrage weirs, as occurs during floods, and establishes correlations for determining the structure’s coefficient of discharge using a two-dimensional (2D) Reynolds averaged Navier Stokes-volume of fluid (RANS-VOF) model, coupled with the renormalization group (RNG) equations. The study specifically examines the piezometric gauging technique, commonly employed in Crump weirs, for estimating the discharge reduction factor of irrigation barrage weirs under submergence and compares the results with those obtained by the traditional tailwater gauging method. The results establish a unique correlation between the discharge reduction factor and the ratio of the piezometric head at a point immediately downstream of the weir crest and the total pressure head at a location on the upstream face of the weir. The method promises a more accurate estimate of the submerged discharge capacity for the barrage weirs than the conventional procedure. The study also suggests that a steeper upstream slope of a weir potentially leads to greater reduction in discharge under submergence. Further, for a given upstream weir face slope, the discharge reduction varies inversely with the relative crest length. The submergence rate at the modular limit is found to be in the range of 0.70–0.78. The modular limit, however, is found to be independent of the upstream face slope. The accuracy and reliability of the computed results are ensured by conducting relevant grid convergence analyses and validating the results of numerical simulations against experimental data.- 1 December 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Irrigation and Drainage Engineering
- Vol. 147 (12) , 04021058
Submerged Flow over Barrage Weirs: A Computational Fluid Dynamics Model Study
Barrage weirs, which are trapezoidal-sectioned sharp-crested weirs having finite crest length, are primarily used in the Indian subcontinent for diverting water for irrigation. This study presents an investigative study on submerged flows over barrage weirs, as occurs during floods, and establishes correlations for determining the structure’s coefficient of discharge using a two-dimensional (2D) Reynolds averaged Navier Stokes-volume of fluid (RANS-VOF) model, coupled with the renormalization group (RNG) equations. The study specifically examines the piezometric gauging technique, commonly employed in Crump weirs, for estimating the discharge reduction factor of irrigation barrage weirs under submergence and compares the results with those obtained by the traditional tailwater gauging method. The results establish a unique correlation between the discharge reduction factor and the ratio of the piezometric head at a point immediately downstream of the weir crest and the total pressure head at a location on the upstream face of the weir. The method promises a more accurate estimate of the submerged discharge capacity for the barrage weirs than the conventional procedure. The study also suggests that a steeper upstream slope of a weir potentially leads to greater reduction in discharge under submergence. Further, for a given upstream weir face slope, the discharge reduction varies inversely with the relative crest length. The submergence rate at the modular limit is found to be in the range of 0.70–0.78. The modular limit, however, is found to be independent of the upstream face slope. The accuracy and reliability of the computed results are ensured by conducting relevant grid convergence analyses and validating the results of numerical simulations against experimental data.- 1 April 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (4) , 043306
Equilibrium approach for modeling erosional failure of granular dams
Erosional failure of granular dams by an overtopping body of water is investigated using a depth-averaged morphodynamic model. The transport of sediment by the flow assumes the sediment flux to remain in equilibrium with the local bed shear stress. Accordingly, the shallow-water hydrodynamic equations are coupled with the Exner equation for mass conservation of the sediment. The system of equations is solved using a fully coupled well-balanced finite volume method, second-order accurate in time and space. The effect of the steep bed slope of a dam face is incorporated into both the hydrodynamics and sediment transport equations, leading to improved predictions. Comparison with results obtained from nonequilibrium sediment transport models indicates that such models perform poorly while predicting the bed evolution near the toe of an eroding dam. Observations from experimental studies demonstrate that the amount of sediment entrained by the flow is not significant, except during the initial moments of failure. This suggests that the vertical exchange of mass between the bed and the flow layer, as assumed by the nonequilibrium models, may not be completely valid during the failure. The equilibrium model results, reproducing the key flow features of the overtopping failure process, are validated by experimental measurements. The study provides fresh insights into the sediment transport processes associated with the erosion of a granular dam by overtopping, establishes the appropriateness of the equilibrium approach for its numerical modeling, and proposes a well-balanced second-order accurate solution technique for solving the resulting coupled equations of flow and sediment transport.
- 1 April 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (4) , 043306
Equilibrium approach for modeling erosional failure of granular dams
Erosional failure of granular dams by an overtopping body of water is investigated using a depth-averaged morphodynamic model. The transport of sediment by the flow assumes the sediment flux to remain in equilibrium with the local bed shear stress. Accordingly, the shallow-water hydrodynamic equations are coupled with the Exner equation for mass conservation of the sediment. The system of equations is solved using a fully coupled well-balanced finite volume method, second-order accurate in time and space. The effect of the steep bed slope of a dam face is incorporated into both the hydrodynamics and sediment transport equations, leading to improved predictions. Comparison with results obtained from nonequilibrium sediment transport models indicates that such models perform poorly while predicting the bed evolution near the toe of an eroding dam. Observations from experimental studies demonstrate that the amount of sediment entrained by the flow is not significant, except during the initial moments of failure. This suggests that the vertical exchange of mass between the bed and the flow layer, as assumed by the nonequilibrium models, may not be completely valid during the failure. The equilibrium model results, reproducing the key flow features of the overtopping failure process, are validated by experimental measurements. The study provides fresh insights into the sediment transport processes associated with the erosion of a granular dam by overtopping, establishes the appropriateness of the equilibrium approach for its numerical modeling, and proposes a well-balanced second-order accurate solution technique for solving the resulting coupled equations of flow and sediment transport.