Seong Gwan Shin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Seong Gwan Shin has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Chung Wung Bark
Department of Electrical Engineering, Gachon University, 1342 Seongnam-daero, Sujeong-gu, Seongnam-si, Gyeonggi-do 13120, Korea
2 shared publications - Hyung Wook Choi
Department of Electrical Engineering, Gachon University, Seongnam 13120, Republic of Korea
2 shared publications Hyung Wook Choi
Electrical Engineering, Gachon University, Seongnam
1 shared publication- Il Tae Kim
School of Chemical, Biological & Battery Engineering, Gachon University, Seongnam-si, Gyeonggi-do, 13120, Republic of Korea
1 shared publication - Kyung Hwan Kim
Department of Electrical Engineering, Gachon University, Seongnam 13120, Republic of Korea
1 shared publication - Sangmo Kim
Department of Intelligent Mechatronics Engineering, Sejong University, Seoul 05006, Republic of Korea
1 shared publication
Latest Publications
- Open Access
Effect of Annealing in ITO Film Prepared at Various Argon-and-Oxygen-Mixture Ratios via Facing-Target Sputtering for Transparent Electrode of Perovskite Solar Cells
Normal perovskite solar cells (PSCs) consist of the following layers: transparent electrode, electron-transport layer (ETL), light-absorbing perovskite layer, hole-transport layer (HTL), and metal electrode. Energy, such as electricity, is produced through light absorbance and electron–hole generation/transport between two electrode types (metal film and transparent conducting film). Among stacked layers in a PSC, the transparent electrode plays the high-performance-power-conversion-efficiency role. Transparent electrodes should have high-visible-range transparency and low resistance. Therefore, in this study, we prepared indium tin oxide (ITO) films on a glass substrate by using facing-target sputtering without substrate heating treatment and investigate the heating-treatment effect on the ITO-film properties for perovskite solar cells (PSCs). Moreover, we fabricated PSCs with ITO films prepared at various oxygen flows during the sputtering process, and their energy-conversion properties are investigated.
Open AccessEffect of Annealing in ITO Film Prepared at Various Argon-and-Oxygen-Mixture Ratios via Facing-Target Sputtering for Transparent Electrode of Perovskite Solar Cells
Normal perovskite solar cells (PSCs) consist of the following layers: transparent electrode, electron-transport layer (ETL), light-absorbing perovskite layer, hole-transport layer (HTL), and metal electrode. Energy, such as electricity, is produced through light absorbance and electron–hole generation/transport between two electrode types (metal film and transparent conducting film). Among stacked layers in a PSC, the transparent electrode plays the high-performance-power-conversion-efficiency role. Transparent electrodes should have high-visible-range transparency and low resistance. Therefore, in this study, we prepared indium tin oxide (ITO) films on a glass substrate by using facing-target sputtering without substrate heating treatment and investigate the heating-treatment effect on the ITO-film properties for perovskite solar cells (PSCs). Moreover, we fabricated PSCs with ITO films prepared at various oxygen flows during the sputtering process, and their energy-conversion properties are investigated.
- Open Access
- 13 April 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (4) , 1000
Study on Performance Improvements in Perovskite-Based Ultraviolet Sensors Prepared Using Toluene Antisolvent and CH3NH3Cl
In this study, a simply structured perovskite-based ultraviolet C (UVC) sensor was prepared using a one-step, low-temperature solution-processing coating method. The UVC sensor utilized CH3NH3PbBr3 perovskite as the light-absorbing layer. To improve the characteristics of CH3NH3PbBr3, an antisolvent process using toluene and the addition of CH3NH3Cl were introduced. The device with these modifications exhibited a response rise/fall time of 15.8/16.2 ms, mobility of 158.7 cm2/V·s, responsivity of 4.57 mA/W, detectivity of 1.02 × 1013 Jones, and external quantum efficiency of 22.32% under the 254-nm UV illumination. Therefore, this methodology could be a good approach in facilitating UVC detection.
- 13 April 2021
- Published by MDPI AG in Nanomaterials
- Vol. 11 (4) , 1000
Open AccessStudy on Performance Improvements in Perovskite-Based Ultraviolet Sensors Prepared Using Toluene Antisolvent and CH3NH3Cl
In this study, a simply structured perovskite-based ultraviolet C (UVC) sensor was prepared using a one-step, low-temperature solution-processing coating method. The UVC sensor utilized CH3NH3PbBr3 perovskite as the light-absorbing layer. To improve the characteristics of CH3NH3PbBr3, an antisolvent process using toluene and the addition of CH3NH3Cl were introduced. The device with these modifications exhibited a response rise/fall time of 15.8/16.2 ms, mobility of 158.7 cm2/V·s, responsivity of 4.57 mA/W, detectivity of 1.02 × 1013 Jones, and external quantum efficiency of 22.32% under the 254-nm UV illumination. Therefore, this methodology could be a good approach in facilitating UVC detection.
- 28 February 2020
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 59 (SG) , SGGF05
A study of perovskite solar cell with a Fe 3+ /Ga 3+ doped TiO 2 layer
Perovskite has a structure of a large number of solar cells, which is very promising for the rapid commercialization of large-scale, low-cost solar cells. Perovskite solar cells (PSCs) have many advantages, such as their simple processing techniques and inexpensive raw materials. The conduction band of TiO 2 used in many PSCs coincides well with that of the perovskite active layer. In addition, TiO 2 has excellent stability and conductivity and can be obtained by various low-cost deposition methods. However, TiO 2 traps electrons in oxygen vacancies and Ti lattice sites; this leads to recombination, which in turn reduces the efficiency of the device. In this study, we investigated the effects of Fe 3+ and Ga 3+ ions on the efficiency of PSCs by doping them in a compact and mesoporous layer of TiO 2 . As a result, the perovskite solar cell using TiO 2 doped with Fe 3+ and Ga 3+ shows an open-circuit voltage of 0.974 V, current density of 21.909 mA cm −2 , 66.646% fill factor, and 14.21% efficiency. Fe 3+ and Ga 3+ have a smaller atomic radius than Ti 4+ and thus, can replace Ti cations. Furthermore, the Fe 3+ and Ga 3+ doping of TiO 2 is considered to be superior for the photoelectric performance of PSCs.
- 28 February 2020
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 59 (SG) , SGGF05
A study of perovskite solar cell with a Fe 3+ /Ga 3+ doped TiO 2 layer
Perovskite has a structure of a large number of solar cells, which is very promising for the rapid commercialization of large-scale, low-cost solar cells. Perovskite solar cells (PSCs) have many advantages, such as their simple processing techniques and inexpensive raw materials. The conduction band of TiO 2 used in many PSCs coincides well with that of the perovskite active layer. In addition, TiO 2 has excellent stability and conductivity and can be obtained by various low-cost deposition methods. However, TiO 2 traps electrons in oxygen vacancies and Ti lattice sites; this leads to recombination, which in turn reduces the efficiency of the device. In this study, we investigated the effects of Fe 3+ and Ga 3+ ions on the efficiency of PSCs by doping them in a compact and mesoporous layer of TiO 2 . As a result, the perovskite solar cell using TiO 2 doped with Fe 3+ and Ga 3+ shows an open-circuit voltage of 0.974 V, current density of 21.909 mA cm −2 , 66.646% fill factor, and 14.21% efficiency. Fe 3+ and Ga 3+ have a smaller atomic radius than Ti 4+ and thus, can replace Ti cations. Furthermore, the Fe 3+ and Ga 3+ doping of TiO 2 is considered to be superior for the photoelectric performance of PSCs.