Han Hao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Han Hao has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Firooz Aflatouni
University of Pennsylvania
5 shared publications - Jan Van der Spiegel
Department of Electrical and Systems Engineering, University of Pennsylvania, Philadelphia, PA, USA
4 shared publications - Andrew G. Richardson
Department of Neurosurgery, University of Pennsylvania, Philadelphia, USA
3 shared publications - Lin Du
University of Pennsylvania
2 shared publications - Mark. G. Allen
University of Pennsylvania
2 shared publications - Ali Pirmoradi
Department of Electrical and Systems Engineering, University of Pennsylvania, Philadelphia, USA
1 shared publication
Latest Publications
- 17 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (7) , 2522-2531
Energy Efficient Monolithically Integrated 256 Gb/s Optical Transmitter With Autonomous Wavelength Stabilization in 45 nm CMOS SOI
This work presents a monolithically integrated eight-channel optical transmitter in the optical C-band. It supports up to 256 Gb/s aggregate data rate using two-section p-n-capacitive micro-ring modulators (MRMs) integrated together with wavelength stabilization circuit, data generator, and high swing electrical drivers on the same CMOS silicon-on-insulator (SOI) chip. The MRMs have an extinction ratio of $>$ 10 dB and a quality factor of about 5000 and can be capacitively tuned over about 400 pm with near-zero power consumption. The energy efficiency of the modulator, including per-channel capacitive wavelength tuning and locking, is 15 fJ/bit at 5-Gb/s/channel and 63 fJ/bit at 32-Gb/s/channel for a bit error rate (BER) $<$ 10 $^{-12}$ and the energy efficiency of the transmitter is 328 fJ/b at 32 Gb/s and 113 fJ/b at 10 Gb/s for a BER $<$ 10 $^{-12}$ . The areal bandwidth density of the modulator unit (including MRMs and the driver electronics) and the core area (including MRMs, drivers, electrical and optical routing, control, and data management electronics) are about 13.25 and 3.3 Tb/s/mm $^{2}$ , respectively. The chip is implemented on a 45 nm CMOS SOI process within a footprint of 1.2 $\times$ 0.5 mm.
- 17 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (7) , 2522-2531
Energy Efficient Monolithically Integrated 256 Gb/s Optical Transmitter With Autonomous Wavelength Stabilization in 45 nm CMOS SOI
This work presents a monolithically integrated eight-channel optical transmitter in the optical C-band. It supports up to 256 Gb/s aggregate data rate using two-section p-n-capacitive micro-ring modulators (MRMs) integrated together with wavelength stabilization circuit, data generator, and high swing electrical drivers on the same CMOS silicon-on-insulator (SOI) chip. The MRMs have an extinction ratio of $>$ 10 dB and a quality factor of about 5000 and can be capacitively tuned over about 400 pm with near-zero power consumption. The energy efficiency of the modulator, including per-channel capacitive wavelength tuning and locking, is 15 fJ/bit at 5-Gb/s/channel and 63 fJ/bit at 32-Gb/s/channel for a bit error rate (BER) $<$ 10 $^{-12}$ and the energy efficiency of the transmitter is 328 fJ/b at 32 Gb/s and 113 fJ/b at 10 Gb/s for a BER $<$ 10 $^{-12}$ . The areal bandwidth density of the modulator unit (including MRMs and the driver electronics) and the core area (including MRMs, drivers, electrical and optical routing, control, and data management electronics) are about 13.25 and 3.3 Tb/s/mm $^{2}$ , respectively. The chip is implemented on a 45 nm CMOS SOI process within a footprint of 1.2 $\times$ 0.5 mm.
- Open Access
- 3 February 2023
- Published by Springer Nature in Research Square
An implantable wireless tactile sensing system
The sense of touch is critical to dexterous use of the hands and thus an essential component to efforts to restore hand function after amputation or paralysis. Prosthetic systems have focused on wearable tactile sensors. But wearable sensors are suboptimal for neuroprosthetic systems designed to reanimate a patient’s own paralyzed hand. Here, we developed an implantable tactile sensing system intended for subdermal placement. The system is composed of a microfabricated capacitive force sensor, a custom integrated circuit supporting wireless powering and data transmission, and a laser-fused hermetic silica package. The miniature device was validated through simulations, benchtop testing, and ex vivo testing in a primate hand. The sensor implanted in the fingertip accurately measured skin forces with a resolution of 4.3 mN. The output from this novel sensor could be encoded in the brain with microstimulation to provide tactile feedback. More broadly, the materials, system design, and fabrication approach establish new foundational capabilities for various applications of implantable sensing systems.
- 3 February 2023
- Published by Springer Nature in Research Square
Open AccessAn implantable wireless tactile sensing system
The sense of touch is critical to dexterous use of the hands and thus an essential component to efforts to restore hand function after amputation or paralysis. Prosthetic systems have focused on wearable tactile sensors. But wearable sensors are suboptimal for neuroprosthetic systems designed to reanimate a patient’s own paralyzed hand. Here, we developed an implantable tactile sensing system intended for subdermal placement. The system is composed of a microfabricated capacitive force sensor, a custom integrated circuit supporting wireless powering and data transmission, and a laser-fused hermetic silica package. The miniature device was validated through simulations, benchtop testing, and ex vivo testing in a primate hand. The sensor implanted in the fingertip accurately measured skin forces with a resolution of 4.3 mN. The output from this novel sensor could be encoded in the brain with microstimulation to provide tactile feedback. More broadly, the materials, system design, and fabrication approach establish new foundational capabilities for various applications of implantable sensing systems.
- 27 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (3) , 869-881
A Wireless Somatosensory Feedback System Using Human Body Communication
This article presents the first integrated somatosensory feedback system based on human body communication (HBC). The proposed wireless system, which is implemented using a 180-nm CMOS process, composed of a wrist device, a brain stimulator device (BSD), and an artificial mechanoreceptor, is designed to restore the sense of touch to a paralyzed hand through tactile sensing and neural stimulation. By utilizing the HBC technique, multiple highly efficient wireless links are realized through the low loss body channel. The self-interference tolerant mixer-first on–off keying (OOK) receiver (RX) achieves 71-dB self-interference rejection at −61-dBm input RF power, with an energy consumption of 36.4 pJ/bit and an area of 0.065 mm 2 . The temperature-stable, 0.17-mm 2 injection locked relaxation oscillator-based frequency-shift keying (FSK) RX achieves an energy consumption of 60 pJ/bit at an input data-rate of 1.2 Mbps and an FSK level difference of 2.2 MHz. A reconfigurable power/FSK transmitter (TX) and a charge-balanced neural stimulator are also presented. The wireless system was demonstrated and verified on human body.
- 27 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 57 (3) , 869-881
A Wireless Somatosensory Feedback System Using Human Body Communication
This article presents the first integrated somatosensory feedback system based on human body communication (HBC). The proposed wireless system, which is implemented using a 180-nm CMOS process, composed of a wrist device, a brain stimulator device (BSD), and an artificial mechanoreceptor, is designed to restore the sense of touch to a paralyzed hand through tactile sensing and neural stimulation. By utilizing the HBC technique, multiple highly efficient wireless links are realized through the low loss body channel. The self-interference tolerant mixer-first on–off keying (OOK) receiver (RX) achieves 71-dB self-interference rejection at −61-dBm input RF power, with an energy consumption of 36.4 pJ/bit and an area of 0.065 mm 2 . The temperature-stable, 0.17-mm 2 injection locked relaxation oscillator-based frequency-shift keying (FSK) RX achieves an energy consumption of 60 pJ/bit at an input data-rate of 1.2 Mbps and an FSK level difference of 2.2 MHz. A reconfigurable power/FSK transmitter (TX) and a charge-balanced neural stimulator are also presented. The wireless system was demonstrated and verified on human body.
- 28 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 15 (2) , 351-364
A 10.8 µW Neural Signal Recorder and Processor With Unsupervised Analog Classifier for Spike Sorting
Implantable brain machine interfaces for treatment of neurological disorders require on-chip, real-time signal processing of action potentials (spikes). In this work, we present the first spike sorting SoC with integrated neural recording front-end and analog unsupervised classifier. The event-driven, low power spike sorter features a novel hardware-optimized, K-means based algorithm that effectively eliminates duplicate clusters and is implemented using a novel clockless and ADC-less analog architecture. The 1.4 mm^2 chip is fabricated in a 180-nm CMOS SOI process. The analog front-end achieves a 3.3 Vrms noise floor over the spike bandwidth (400 5000 Hz) and consumes 6.42 from a 1.5 V supply. The analog spike sorter consumes 4.35 and achieves 93.2% classification accuracy on a widely used synthetic test dataset. In addition, higher than 93% agreement between the chip classification result and that of a standard spike sorting software is observed using pre-recorded real neural signals. Simulations of the implemented spike sorter show robust performance under process-voltage-temperature variations.
- 28 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 15 (2) , 351-364
A 10.8 µW Neural Signal Recorder and Processor With Unsupervised Analog Classifier for Spike Sorting
Implantable brain machine interfaces for treatment of neurological disorders require on-chip, real-time signal processing of action potentials (spikes). In this work, we present the first spike sorting SoC with integrated neural recording front-end and analog unsupervised classifier. The event-driven, low power spike sorter features a novel hardware-optimized, K-means based algorithm that effectively eliminates duplicate clusters and is implemented using a novel clockless and ADC-less analog architecture. The 1.4 mm^2 chip is fabricated in a 180-nm CMOS SOI process. The analog front-end achieves a 3.3 Vrms noise floor over the spike bandwidth (400 5000 Hz) and consumes 6.42 from a 1.5 V supply. The analog spike sorter consumes 4.35 and achieves 93.2% classification accuracy on a widely used synthetic test dataset. In addition, higher than 93% agreement between the chip classification result and that of a standard spike sorting software is observed using pre-recorded real neural signals. Simulations of the implemented spike sorter show robust performance under process-voltage-temperature variations.
- 22 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (6) , 2907-2920
A Wireless Artificial Mechanoreceptor in 180-nm CMOS
This article presents an implantable low-power wireless integrated system for tactile sensing applications. The reported application-specified integrated circuit (ASIC) uses a low-loss magnetic human body communication channel for both wireless power and data transfer. The chip is hybrid-integrated with an in-house fabricated MEMS capacitive force sensor to form an implantable artificial mechanoreceptor. An on-chip correlated double sampling capacitance to time converter (CTC) consumes 750 nW from a 1.2-V on-chip regulated supply, achieving a 2.0-fF resolution for an input capacitance of 14 pF and a FoM of 49 fJ/c-s while occupying an area of only 0.04 mm 2 . The CTC has a time-multiplexed mode to interface with four input capacitors. Wireless power management feedback is used to ensure robust operation in the presence of hand gesture changes and process–voltage–temperature variations. The on-chip data transmitter can operate in ON–OFF keying (OOK) or frequency-shift keying modulation formats, where it consumes only $7.8~\mu \text{W}$ in the OOK mode. The 1.62-mm 2 chip is fabricated in a standard 180-nm CMOS process and consumes $110.3~\mu \text{W}$ .
- 22 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (6) , 2907-2920
A Wireless Artificial Mechanoreceptor in 180-nm CMOS
This article presents an implantable low-power wireless integrated system for tactile sensing applications. The reported application-specified integrated circuit (ASIC) uses a low-loss magnetic human body communication channel for both wireless power and data transfer. The chip is hybrid-integrated with an in-house fabricated MEMS capacitive force sensor to form an implantable artificial mechanoreceptor. An on-chip correlated double sampling capacitance to time converter (CTC) consumes 750 nW from a 1.2-V on-chip regulated supply, achieving a 2.0-fF resolution for an input capacitance of 14 pF and a FoM of 49 fJ/c-s while occupying an area of only 0.04 mm 2 . The CTC has a time-multiplexed mode to interface with four input capacitors. Wireless power management feedback is used to ensure robust operation in the presence of hand gesture changes and process–voltage–temperature variations. The on-chip data transmitter can operate in ON–OFF keying (OOK) or frequency-shift keying modulation formats, where it consumes only $7.8~\mu \text{W}$ in the OOK mode. The 1.62-mm 2 chip is fabricated in a standard 180-nm CMOS process and consumes $110.3~\mu \text{W}$ .