Michael Müller
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Michael Müller has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Elena López
Fraunhofer Institute for Material and Beam Technology IWS, 01277 Dresden, Germany
3 shared publications Frank Brueckner
Department of Additive Manufacturing, Fraunhofer Institute for Material and Beam Technology, Dresden, Germany
3 shared publicationsC. Leyens
Fraunhofer IWS, Dresden, Germany
2 shared publicationsChristoph Leyens
Department of Additive Manufacturing, Fraunhofer Institute for Material and Beam Technology, Dresden, Germany
2 shared publications- Christoph Leyens
TU Dresden
2 shared publications Elena López
Department of Additive Manufacturing, Fraunhofer Institute for Material and Beam Technology, Dresden, Germany
2 shared publications
Latest Publications
- Open Access
- 1 March 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (12)
Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere
Surface tension plays a key role in determining melt behavior, wetting, and defect formation in high‐temperature processes such as laser powder bed fusion and wire‐based deposition welding. Accurate surface tension data are therefore essential for optimizing process quality, especially for titanium alloys, like Ti‐6Al‐4V, which are widely used in aerospace and biomedical applications due to their high specific strength and biocompatibility. In this article, the surface tension of Ti‐6Al‐4V is derived from the oscillation of falling droplets using Rayleigh's formula. Conventional levitating droplet techniques for reactive materials require complex evaluation algorithms and specialized hardware to maintain microgravity conditions. In contrast, the presented approach employs only a single high‐speed camera for simultaneous temperature and droplet oscillation measurements, enabling flexible and cost‐effective integration into various technical systems. The method is applied to investigate the influence of residual oxygen on the surface tension by performing experiments in argon and in a monosilane‐doped oxygen‐free atmosphere (−15 ppm O 2 ). The surface tension follows the linear relation γ ( T ) = 1.512 N m −1 − 1.468 × 10 −4 N m −1 K −1 × ( T − 1933 K). No measurable influence of residual oxygen was observed, as the droplet lifetime was four orders of magnitude shorter than the time required for substantial oxygen diffusion.
- 1 March 2026
- Published by Wiley in Advanced Engineering Materials
- Vol. 28 (12)
Open AccessSurface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere
Surface tension plays a key role in determining melt behavior, wetting, and defect formation in high‐temperature processes such as laser powder bed fusion and wire‐based deposition welding. Accurate surface tension data are therefore essential for optimizing process quality, especially for titanium alloys, like Ti‐6Al‐4V, which are widely used in aerospace and biomedical applications due to their high specific strength and biocompatibility. In this article, the surface tension of Ti‐6Al‐4V is derived from the oscillation of falling droplets using Rayleigh's formula. Conventional levitating droplet techniques for reactive materials require complex evaluation algorithms and specialized hardware to maintain microgravity conditions. In contrast, the presented approach employs only a single high‐speed camera for simultaneous temperature and droplet oscillation measurements, enabling flexible and cost‐effective integration into various technical systems. The method is applied to investigate the influence of residual oxygen on the surface tension by performing experiments in argon and in a monosilane‐doped oxygen‐free atmosphere (−15 ppm O 2 ). The surface tension follows the linear relation γ ( T ) = 1.512 N m −1 − 1.468 × 10 −4 N m −1 K −1 × ( T − 1933 K). No measurable influence of residual oxygen was observed, as the droplet lifetime was four orders of magnitude shorter than the time required for substantial oxygen diffusion.
- Open Access
- 1 February 2026
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (1)
Detection of melt pool oscillations in oxygen free PBF-LB/M
Laser-based powder bed fusion of metals (PBF-LB/M) is a complex process that is strongly determined by the dynamic properties of the rapidly moving melt pool. Investigating spatter formation mechanisms, melt pool oscillations, as well as depth, size, and shape of the melt pool is necessary for an in-depth understanding of process behavior. However, the small scale of the melt pool, high scanning velocities, and bright thermal and metal vapor emissions complicate direct observations of the process zone often requiring complex equipment such as x-ray systems that are only accessible for limited applications. Therefore, in this paper, an advanced in situ process monitoring system consisting of a narrow bandwidth laser illumination combined with a high-speed camera is implemented into an experimental laboratory PBF-LB/M machine. This system enables the visualization of melt pool behavior independent of process emissions at 50 000 FPS. The image processing algorithms for determining geometrical features like melt pool size, shape, and aspect ratio are described. Furthermore, the frequencies of the dynamic melt pool surface oscillations are extracted and correlated with the processing conditions. This technique is then applied on the PBF-LB/M-process of titanium in a monosilane-doped extreme high vacuum adequate atmosphere with an ultralow oxygen content of <10−15 ppm. The investigations indicate a strong correlation between the energy input and the oscillation frequency ranging from 4.1 kHz at 2 W/mm to 10 kHz at 0.5 W/mm as the oscillatory mass decreases. The results demonstrate the potential for monitoring the melt pool depth by observing surface oscillations.
- 1 February 2026
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (1)
Open AccessDetection of melt pool oscillations in oxygen free PBF-LB/M
Laser-based powder bed fusion of metals (PBF-LB/M) is a complex process that is strongly determined by the dynamic properties of the rapidly moving melt pool. Investigating spatter formation mechanisms, melt pool oscillations, as well as depth, size, and shape of the melt pool is necessary for an in-depth understanding of process behavior. However, the small scale of the melt pool, high scanning velocities, and bright thermal and metal vapor emissions complicate direct observations of the process zone often requiring complex equipment such as x-ray systems that are only accessible for limited applications. Therefore, in this paper, an advanced in situ process monitoring system consisting of a narrow bandwidth laser illumination combined with a high-speed camera is implemented into an experimental laboratory PBF-LB/M machine. This system enables the visualization of melt pool behavior independent of process emissions at 50 000 FPS. The image processing algorithms for determining geometrical features like melt pool size, shape, and aspect ratio are described. Furthermore, the frequencies of the dynamic melt pool surface oscillations are extracted and correlated with the processing conditions. This technique is then applied on the PBF-LB/M-process of titanium in a monosilane-doped extreme high vacuum adequate atmosphere with an ultralow oxygen content of <10−15 ppm. The investigations indicate a strong correlation between the energy input and the oscillation frequency ranging from 4.1 kHz at 2 W/mm to 10 kHz at 0.5 W/mm as the oscillatory mass decreases. The results demonstrate the potential for monitoring the melt pool depth by observing surface oscillations.
- Open Access
- 25 July 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 134 (1-2) , 657-675
Laser-based directed energy deposition and characterisation of cBN-reinforced NiAl-based coatings
Within this study, the alloy NiAl–2.5Ta–7.5Cr is investigated as a new matrix material for cBN-reinforced abrasive turbine blade tip coatings as currently used NiCoCrAlY matrix alloys suffer from insufficient strength at the high operating temperatures. Laser-based directed energy deposition with blown powder was applied to produce cBN reinforced NiAl-based coatings on monocrystalline CMSX-4 substrates. For this, powdery titanium-coated cBN and NiAl–2.5Ta–7.5Cr material were co-injected into the process zone to achieve an in situ formation of a NiAl–2.5Ta–7.5Cr/cBN composite. In order to overcome challenges such as cracking susceptibility, inductive preheating of the substrate up to 800 °C was used. Optical and scanning electron microscopy, energy dispersive X-ray spectroscopy, as well as electron backscatter diffraction were applied to analyse the fabricated samples’ microstructure. Additionally, the mechanical properties were evaluated by means of microhardness mappings. This work demonstrates the feasibility of in situ forming a metal matrix composite with a homogeneous distribution of cBN particles. The results show the beneficial effect of high-temperature preheating on the crack formation. However, the study also reveals challenges such as cracking induced by the injected cBN particles as well as severe intermixing of substrate and coating, which yields spatially resolved deviations in the chemical composition and resulting variations in microstructure and hardness. Graphical
- 25 July 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 134 (1-2) , 657-675
Open AccessLaser-based directed energy deposition and characterisation of cBN-reinforced NiAl-based coatings
Within this study, the alloy NiAl–2.5Ta–7.5Cr is investigated as a new matrix material for cBN-reinforced abrasive turbine blade tip coatings as currently used NiCoCrAlY matrix alloys suffer from insufficient strength at the high operating temperatures. Laser-based directed energy deposition with blown powder was applied to produce cBN reinforced NiAl-based coatings on monocrystalline CMSX-4 substrates. For this, powdery titanium-coated cBN and NiAl–2.5Ta–7.5Cr material were co-injected into the process zone to achieve an in situ formation of a NiAl–2.5Ta–7.5Cr/cBN composite. In order to overcome challenges such as cracking susceptibility, inductive preheating of the substrate up to 800 °C was used. Optical and scanning electron microscopy, energy dispersive X-ray spectroscopy, as well as electron backscatter diffraction were applied to analyse the fabricated samples’ microstructure. Additionally, the mechanical properties were evaluated by means of microhardness mappings. This work demonstrates the feasibility of in situ forming a metal matrix composite with a homogeneous distribution of cBN particles. The results show the beneficial effect of high-temperature preheating on the crack formation. However, the study also reveals challenges such as cracking induced by the injected cBN particles as well as severe intermixing of substrate and coating, which yields spatially resolved deviations in the chemical composition and resulting variations in microstructure and hardness. Graphical
- Open Access
- 26 January 2024
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 36 (1)
Process qualification, additive manufacturing, and postprocessing of a hydrogen peroxide/kerosene 6 kN aerospike breadboard engine
This contribution addresses the complete process chain of an annular aerospike breadboard engine fabricated by laser powder bed fusion using the nickel-based superalloy Inconel® 718. In order to qualify the material and process for this high-temperature application, an extensive material characterization campaign including density and roughness measurements, as well as tensile tests at room temperature, 700, and 900 °C, was conducted. In addition, various geometric features such as triangles, ellipses, and circular shapes were generated to determine the maximum unsupported overhang angle and geometrical accuracy. The results were taken into account in the design maturation of the manifold and the cooling channels of the aerospike breadboard engine. Postprocessing included heat treatment to increase mechanical properties, milling, turning, and eroding of interfaces to fulfill the geometrical tolerances, thermal barrier coating of thermally stressed surfaces for better protection of thermal loads, and laser welding of spike and shroud for the final assembly as well as quality assurance. This contribution goes beyond small density cubes and tensile samples and offers details on the iterations necessary for the successful printing of large complex shaped functional parts. The scientific question is how to verify the additive manufacturing process through tensile testing, simulation, and design iterations for complex geometries and reduce the number of failed prints.
- 26 January 2024
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 36 (1)
Open AccessProcess qualification, additive manufacturing, and postprocessing of a hydrogen peroxide/kerosene 6 kN aerospike breadboard engine
This contribution addresses the complete process chain of an annular aerospike breadboard engine fabricated by laser powder bed fusion using the nickel-based superalloy Inconel® 718. In order to qualify the material and process for this high-temperature application, an extensive material characterization campaign including density and roughness measurements, as well as tensile tests at room temperature, 700, and 900 °C, was conducted. In addition, various geometric features such as triangles, ellipses, and circular shapes were generated to determine the maximum unsupported overhang angle and geometrical accuracy. The results were taken into account in the design maturation of the manifold and the cooling channels of the aerospike breadboard engine. Postprocessing included heat treatment to increase mechanical properties, milling, turning, and eroding of interfaces to fulfill the geometrical tolerances, thermal barrier coating of thermally stressed surfaces for better protection of thermal loads, and laser welding of spike and shroud for the final assembly as well as quality assurance. This contribution goes beyond small density cubes and tensile samples and offers details on the iterations necessary for the successful printing of large complex shaped functional parts. The scientific question is how to verify the additive manufacturing process through tensile testing, simulation, and design iterations for complex geometries and reduce the number of failed prints.
- Open Access
- 6 July 2023
- Published by Springer Nature in Journal of Materials Science
- Vol. 58 (27) , 11310-11326
Influence of process parameter variation on the microstructure of thin walls made of Inconel 718 deposited via laser-based directed energy deposition with blown powder
In laser-based directed energy deposition (L-DED) of Inconel 718 the microstructure of the fabricated components strongly depends on the applied process parameters and the resulting solidification conditions. Numerous studies have shown that the process parameters deposition speed and laser power have a major influences on microstructural properties, such as dendrite morphology and segregation behavior. This study investigates how changes in these process parameters affect the microstructure and hardness when the line mass, and thus the resulting layer height, are kept constant. This enables the microstructural comparison of geometrically similar specimens that were manufactured with the same number of layers but severely different process parameters. This approach yields the benefit of almost identical geometrical boundary conditions, such as the layer-specific build-height and heat conducting cross section, for all specimens. For microstructural analysis scanning electron microscopy and energy dispersive X-ray spectroscopy were applied and the results evaluated in a quantitative manner. The microstructural features primary dendritic arm spacing, fraction and morphology of precipitated Laves phase as well as the spatially resolved chemical composition were measured along the build-up direction. The occurring cooling rates were calculated based on the primary dendritic arm spacing using semi-empirical models. Three different models used by others researchers were applied and evaluated with respect to their applicability for L-DED. Finally, microhardness measurements were performed for a baseline evaluation of the influence on the materials’ mechanical properties.
- 6 July 2023
- Published by Springer Nature in Journal of Materials Science
- Vol. 58 (27) , 11310-11326
Open AccessInfluence of process parameter variation on the microstructure of thin walls made of Inconel 718 deposited via laser-based directed energy deposition with blown powder
In laser-based directed energy deposition (L-DED) of Inconel 718 the microstructure of the fabricated components strongly depends on the applied process parameters and the resulting solidification conditions. Numerous studies have shown that the process parameters deposition speed and laser power have a major influences on microstructural properties, such as dendrite morphology and segregation behavior. This study investigates how changes in these process parameters affect the microstructure and hardness when the line mass, and thus the resulting layer height, are kept constant. This enables the microstructural comparison of geometrically similar specimens that were manufactured with the same number of layers but severely different process parameters. This approach yields the benefit of almost identical geometrical boundary conditions, such as the layer-specific build-height and heat conducting cross section, for all specimens. For microstructural analysis scanning electron microscopy and energy dispersive X-ray spectroscopy were applied and the results evaluated in a quantitative manner. The microstructural features primary dendritic arm spacing, fraction and morphology of precipitated Laves phase as well as the spatially resolved chemical composition were measured along the build-up direction. The occurring cooling rates were calculated based on the primary dendritic arm spacing using semi-empirical models. Three different models used by others researchers were applied and evaluated with respect to their applicability for L-DED. Finally, microhardness measurements were performed for a baseline evaluation of the influence on the materials’ mechanical properties.
- Open Access
- 22 December 2022
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 35 (1) , 012006
Multimaterial direct energy deposition: From three-dimensionally graded components to rapid alloy development for advanced materials
Laser-based direct energy deposition (L-DED) with blown powder enables the simultaneous or sequential processing of different powder materials within one component and, thus, offers the possibility of additive multimaterial manufacturing. Therefore, the process allows a spatially resolved material allocation and fabrication of sharp or even graded material transitions. Within this contribution, the latest results from two major research fields in multimaterial L-DED—(I) automation and (II) rapid alloy development of high entropy alloys (HEAs) by in situ synthesis—shall be presented. First, an automated multimaterial deposition process was developed, which enables the automated manufacturing of three-dimensionally graded specimens. For this, a characterization of the deposition system regarding powder feeding dynamics and resulting powder mixtures in the process zone was conducted. The obtained system characteristics were used to achieve a three-dimensional deposition of specified powder mixtures. The fabricated specimens were analyzed by energy-dispersive x-ray spectroscopy, scanning electron microscopy, and micro hardness measurement. The research demonstrates the increasing readiness of L-DED for the fabrication of multimaterial components. Second, the latest results from rapid alloy development for HEAs by DED are presented. By the simultaneous usage of up to four powder feeders, a vast range of alloy compositions within the Al–Ti–Co–Cr–Fe–Ni HEA system was investigated. For this, tailored measurement systems such as an in-house developed powder sensor were beneficially used. The study shows the influence of a variation of Al on the phase formation and resulting mechanical properties and demonstrates the potential of L-DED for reducing development times for new alloys.
- 22 December 2022
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 35 (1) , 012006
Open AccessMultimaterial direct energy deposition: From three-dimensionally graded components to rapid alloy development for advanced materials
Laser-based direct energy deposition (L-DED) with blown powder enables the simultaneous or sequential processing of different powder materials within one component and, thus, offers the possibility of additive multimaterial manufacturing. Therefore, the process allows a spatially resolved material allocation and fabrication of sharp or even graded material transitions. Within this contribution, the latest results from two major research fields in multimaterial L-DED—(I) automation and (II) rapid alloy development of high entropy alloys (HEAs) by in situ synthesis—shall be presented. First, an automated multimaterial deposition process was developed, which enables the automated manufacturing of three-dimensionally graded specimens. For this, a characterization of the deposition system regarding powder feeding dynamics and resulting powder mixtures in the process zone was conducted. The obtained system characteristics were used to achieve a three-dimensional deposition of specified powder mixtures. The fabricated specimens were analyzed by energy-dispersive x-ray spectroscopy, scanning electron microscopy, and micro hardness measurement. The research demonstrates the increasing readiness of L-DED for the fabrication of multimaterial components. Second, the latest results from rapid alloy development for HEAs by DED are presented. By the simultaneous usage of up to four powder feeders, a vast range of alloy compositions within the Al–Ti–Co–Cr–Fe–Ni HEA system was investigated. For this, tailored measurement systems such as an in-house developed powder sensor were beneficially used. The study shows the influence of a variation of Al on the phase formation and resulting mechanical properties and demonstrates the potential of L-DED for reducing development times for new alloys.
- Open Access
- 28 September 2021
- Published by Wiley in Advanced Engineering Materials
- Vol. 24 (4) , 2100993
Multimaterial Additive Manufacturing of Graded Laves Phase Reinforced NiAlTa Structures by Means of Laser Metal Deposition
Recently, the additive manufacturing (AM) technology laser metal deposition (LMD) has gained a lot of attention for processing crack prone high temperature materials such as nickel‐based superalloys or intermetallics. A feasibility study on LMD of a graded transition from binary ß‐NiAl to Ni50Al42Ta8 is presented with the aim to show the possibility of manufacturing ß‐NiAl‐based structures with a spatially resolved microstructure and subsequently tailored mechanical properties. For achieving this, the alloys Ni50Al50 and Ni50Al42Ta8 are coinjected into the process zone and the powder feeding rates are adapted in a layerwise manner. Due to preheating temperatures of up to 1000 °C, the transition can be manufactured with high relative density and a low degree of cold cracking. Scanning electron microscopy of the transition zone shows the formation of a fine dendritic microstructure consisting of ß‐NiAl dendritic and NiAlTa interdendritic regions. Large area energy‐dispersive X‐ray analysis reveals a gradient in NiAlTa Laves phase content with increasing build height. The observed volume fraction of Laves phase corresponds well to reported values from cast ingots. Finally, hardness measurements along the build‐up direction show an increase in hardness from 300 HV0.1 to 680 HV0.1 indicating a tremendous increase in tensile strength.
- 28 September 2021
- Published by Wiley in Advanced Engineering Materials
- Vol. 24 (4) , 2100993
Open AccessMultimaterial Additive Manufacturing of Graded Laves Phase Reinforced NiAlTa Structures by Means of Laser Metal Deposition
Recently, the additive manufacturing (AM) technology laser metal deposition (LMD) has gained a lot of attention for processing crack prone high temperature materials such as nickel‐based superalloys or intermetallics. A feasibility study on LMD of a graded transition from binary ß‐NiAl to Ni50Al42Ta8 is presented with the aim to show the possibility of manufacturing ß‐NiAl‐based structures with a spatially resolved microstructure and subsequently tailored mechanical properties. For achieving this, the alloys Ni50Al50 and Ni50Al42Ta8 are coinjected into the process zone and the powder feeding rates are adapted in a layerwise manner. Due to preheating temperatures of up to 1000 °C, the transition can be manufactured with high relative density and a low degree of cold cracking. Scanning electron microscopy of the transition zone shows the formation of a fine dendritic microstructure consisting of ß‐NiAl dendritic and NiAlTa interdendritic regions. Large area energy‐dispersive X‐ray analysis reveals a gradient in NiAlTa Laves phase content with increasing build height. The observed volume fraction of Laves phase corresponds well to reported values from cast ingots. Finally, hardness measurements along the build‐up direction show an increase in hardness from 300 HV0.1 to 680 HV0.1 indicating a tremendous increase in tensile strength.
- Open Access
Additive Manufacturing of β-NiAl by Means of Laser Metal Deposition of Pre-Alloyed and Elemental Powders
The additive manufacturing (AM) technique, laser metal deposition (LMD), combines the advantages of near net shape manufacturing, tailored thermal process conditions and in situ alloy modification. This makes LMD a promising approach for the processing of advanced materials, such as intermetallics. Additionally, LMD allows the composition of a powder blend to be modified in situ. Hence, alloying and material build-up can be achieved simultaneously. Within this contribution, AM processing of the promising high-temperature material β-NiAl, by means of LMD, with elemental powder blends, as well as with pre-alloyed powders, was presented. The investigations showed that by applying a preheating temperature of 1100 °C, β-NiAl could be processed without cracking. Additionally, by using pre-alloyed, as well as elemental powders, a single phase β-NiAl microstructure can be achieved in multi-layer build-ups. Major differences between the approaches were found within substrate near regions. For in situ alloying of Ni and Al, these regions are characterized by an inhomogeneous elemental distribution in a layerwise manner. However, due to the remelting of preceding layers during deposition, a homogenization can be observed, leading to a single-phase structure. This shows the potential of high temperature preheating and in situ alloying to push the development of new high temperature materials for AM.
Open AccessAdditive Manufacturing of β-NiAl by Means of Laser Metal Deposition of Pre-Alloyed and Elemental Powders
The additive manufacturing (AM) technique, laser metal deposition (LMD), combines the advantages of near net shape manufacturing, tailored thermal process conditions and in situ alloy modification. This makes LMD a promising approach for the processing of advanced materials, such as intermetallics. Additionally, LMD allows the composition of a powder blend to be modified in situ. Hence, alloying and material build-up can be achieved simultaneously. Within this contribution, AM processing of the promising high-temperature material β-NiAl, by means of LMD, with elemental powder blends, as well as with pre-alloyed powders, was presented. The investigations showed that by applying a preheating temperature of 1100 °C, β-NiAl could be processed without cracking. Additionally, by using pre-alloyed, as well as elemental powders, a single phase β-NiAl microstructure can be achieved in multi-layer build-ups. Major differences between the approaches were found within substrate near regions. For in situ alloying of Ni and Al, these regions are characterized by an inhomogeneous elemental distribution in a layerwise manner. However, due to the remelting of preceding layers during deposition, a homogenization can be observed, leading to a single-phase structure. This shows the potential of high temperature preheating and in situ alloying to push the development of new high temperature materials for AM.