Ege Anıl Diler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ege Anıl Diler has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Akın Ataş
Department of Mechanical, Aerospace and Civil Engineering , University of Manchester , Manchester , UK
2 shared publicationsBatuhan Kayhan
1 shared publication- Cemile Kayiş
Ege University, Faculty of Engineering
1 shared publication - Cemile Kayış
Graduate School of Natural and Applied Sciences, Ege University, Izmir 35040, Turkey
1 shared publication - Ege Gülçiçek1 shared publication
Fatih Balikoglu
Department of Mechanical Engineering, Balikesir University, Balikesir, Turkey
1 shared publication
Latest Publications
- Open Access
Improving Electrical Conductivity of Commercially Pure Aluminium: The Synergistic Effect of AlB8 Master Alloy and Heat Treatment
This study aims to enhance the electrical conductivity of commercially pure aluminium by minimizing impurities and grain boundaries in its microstructure, ultimately improving the efficiency of electric motors constructed from rotors with squirrel cages made from this material. For this purpose, an aluminium–boron (AlB8) master alloy was added to aluminium with a purity of 99.7%, followed by the application of a grain-coarsening heat treatment to the rotors. To obtain commercially pure aluminium with boron additions of 0.05% and 0.1% by weight, specific amounts of the AlB8 master alloy were added into aluminium with a purity of 99.7%. Using these materials, squirrel cage components of rotors were produced via the high-pressure die-casting method. Subsequently, a grain-coarsening heat treatment of the rotors was performed at temperatures of 450 °C, 500 °C, and 550 °C, with holding times of 2, 6, and 10 h. The Box–Behnken design, which is based on statistical experimental design and response surface methodology, was employed to investigate the effects of adding boron and varying the heat treatment temperature and holding time on the electrical conductivity of commercially pure aluminium. The results showed that the synergistic effect of adding boron at 0.05 wt.% and applying the grain-coarsening heat treatment at a temperature of 550 °C for a holding time of 10 h significantly enhanced the electrical conductivity of commercially pure aluminium, increasing it from 60.62% IACS to 63.1% IACS. Correspondingly, the efficiency of the electric motor increased from 90.35% to 91.53%. These findings suggest that this hybrid method not only enhances the electrical conductivity of commercially pure aluminium but also has strong potential to improve its other properties, such as thermal conductivity. This will lead to products composed of components manufactured from the materials exhibiting better performance characteristics, such as increased efficiency and extended service life. Consequently, this innovative method will contribute economically and environmentally by facilitating the manufacture of high-performance products.
Open AccessImproving Electrical Conductivity of Commercially Pure Aluminium: The Synergistic Effect of AlB8 Master Alloy and Heat Treatment
This study aims to enhance the electrical conductivity of commercially pure aluminium by minimizing impurities and grain boundaries in its microstructure, ultimately improving the efficiency of electric motors constructed from rotors with squirrel cages made from this material. For this purpose, an aluminium–boron (AlB8) master alloy was added to aluminium with a purity of 99.7%, followed by the application of a grain-coarsening heat treatment to the rotors. To obtain commercially pure aluminium with boron additions of 0.05% and 0.1% by weight, specific amounts of the AlB8 master alloy were added into aluminium with a purity of 99.7%. Using these materials, squirrel cage components of rotors were produced via the high-pressure die-casting method. Subsequently, a grain-coarsening heat treatment of the rotors was performed at temperatures of 450 °C, 500 °C, and 550 °C, with holding times of 2, 6, and 10 h. The Box–Behnken design, which is based on statistical experimental design and response surface methodology, was employed to investigate the effects of adding boron and varying the heat treatment temperature and holding time on the electrical conductivity of commercially pure aluminium. The results showed that the synergistic effect of adding boron at 0.05 wt.% and applying the grain-coarsening heat treatment at a temperature of 550 °C for a holding time of 10 h significantly enhanced the electrical conductivity of commercially pure aluminium, increasing it from 60.62% IACS to 63.1% IACS. Correspondingly, the efficiency of the electric motor increased from 90.35% to 91.53%. These findings suggest that this hybrid method not only enhances the electrical conductivity of commercially pure aluminium but also has strong potential to improve its other properties, such as thermal conductivity. This will lead to products composed of components manufactured from the materials exhibiting better performance characteristics, such as increased efficiency and extended service life. Consequently, this innovative method will contribute economically and environmentally by facilitating the manufacture of high-performance products.
- Open Access
- 1 August 2022
- Published by Avestia Publishing
Investigation of the Effects of Process Parameters for Friction Stir Spot Welding of Thin Al 6061 Sheet
- 1 August 2022
- Published by Avestia Publishing
Open AccessInvestigation of the Effects of Process Parameters for Friction Stir Spot Welding of Thin Al 6061 Sheet
- 31 July 2022
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 10 (3) , 1344-1358
Effects of TiN/CrN, CrAlN, and TiN Coatings on the Performance of AISI M2 Tool Steel
The aim of this study is to investigate the effects of various ceramic-based coatings on the performance of AISI M2 high-speed steel punch used in the nut piercing process. AISI M2 punches were coated with TiN, TiN/CrN, and CrAlN utilizing a physical vapour deposition method. The total stroke number of the punches was used to evaluate the tool life of TiN, CrAlN, and TiN/CrN coated AISI M2 punches. AISI M2 punch coated with TiN/CrN was able to work up to greater stroke numbers than punches coated with TiN and CrAlN. Hardness and wear tests were performed to study the wear resistance of TiN/CrN and CrAlN coatings under relatively normal load conditions compared to actual working conditions (impact loading conditions) in the piercing process. The hardness and wear resistance of the CrAlN coating were greater than those of the TiN/CrN coating. The wear performance of the CrAlN coating was higher at normal loads and sliding speeds while the tool life of the TiN/CrN-coated punch was better under impact loading conditions.
- 31 July 2022
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 10 (3) , 1344-1358
Effects of TiN/CrN, CrAlN, and TiN Coatings on the Performance of AISI M2 Tool Steel
The aim of this study is to investigate the effects of various ceramic-based coatings on the performance of AISI M2 high-speed steel punch used in the nut piercing process. AISI M2 punches were coated with TiN, TiN/CrN, and CrAlN utilizing a physical vapour deposition method. The total stroke number of the punches was used to evaluate the tool life of TiN, CrAlN, and TiN/CrN coated AISI M2 punches. AISI M2 punch coated with TiN/CrN was able to work up to greater stroke numbers than punches coated with TiN and CrAlN. Hardness and wear tests were performed to study the wear resistance of TiN/CrN and CrAlN coatings under relatively normal load conditions compared to actual working conditions (impact loading conditions) in the piercing process. The hardness and wear resistance of the CrAlN coating were greater than those of the TiN/CrN coating. The wear performance of the CrAlN coating was higher at normal loads and sliding speeds while the tool life of the TiN/CrN-coated punch was better under impact loading conditions.
- Open Access
- 15 April 2022
- Published by Walter de Gruyter GmbH in International Journal of Materials Research
- Vol. 113 (6) , 587-598
Strain rate effect on the tensile properties of plain weave aramid, carbon, and glass fabric reinforced monolithic and hybrid composites
The tensile responses of three monolithic composites (aramid, carbon, and glass) and three different interply hybrid composite laminates (aramid/carbon, glass/aramid, and glass/carbon) were studied at quasi-static and intermediate strain rates. Monolithic composites were found to be more sensitive to strain rate than hybrid counterparts. The hybrids with glass layers had the highest sensitivity among the hybrid laminates. Tensile strengths of aramid, carbon, and glass monolithic composites improved by 15.2 %, 10.1 %, and 22.2 %, respectively, as the strain rate was increased from 0.001 s−1 to 10 s−1, while increases in tensile strengths of aramid/carbon, glass/aramid and glass/carbon hybrid laminates were 8.8 %, 17.7 %, and 5.2 %, respectively. Hybridization of glass with aramid gave the highest failure strain gain. Carbon layers located at the centre of the hybrid laminates resulted in increased tensile strength.
- 15 April 2022
- Published by Walter de Gruyter GmbH in International Journal of Materials Research
- Vol. 113 (6) , 587-598
Open AccessStrain rate effect on the tensile properties of plain weave aramid, carbon, and glass fabric reinforced monolithic and hybrid composites
The tensile responses of three monolithic composites (aramid, carbon, and glass) and three different interply hybrid composite laminates (aramid/carbon, glass/aramid, and glass/carbon) were studied at quasi-static and intermediate strain rates. Monolithic composites were found to be more sensitive to strain rate than hybrid counterparts. The hybrids with glass layers had the highest sensitivity among the hybrid laminates. Tensile strengths of aramid, carbon, and glass monolithic composites improved by 15.2 %, 10.1 %, and 22.2 %, respectively, as the strain rate was increased from 0.001 s−1 to 10 s−1, while increases in tensile strengths of aramid/carbon, glass/aramid and glass/carbon hybrid laminates were 8.8 %, 17.7 %, and 5.2 %, respectively. Hybridization of glass with aramid gave the highest failure strain gain. Carbon layers located at the centre of the hybrid laminates resulted in increased tensile strength.
- 30 December 2021
- Published by Marmara University in International Journal of Advances in Engineering and Pure Sciences
- Vol. 33 (4) , 526-536
Electrical, Thermal, and Mechanical Properties of Mg-TiB2 Nanocomposites Produced by Spark Plasma Sintering
Monolithic magnesium was reinforced with nano-TiB2 particles to produce Mg-TiB2 nanocomposites, and the effects of nano-TiB2 particles on the electrical, thermal, and mechanical properties of Mg matrix nanocomposites were studied. Monolithic Mg and Mg-TiB2 nanocomposites were manufactured using spark plasma sintering process. Both analytical and experimental findings revealed that the electrical and thermal conductivities of Mg-TiB2 nanocomposites were lower than those of monolithic Mg and decreased as the amount of nano-TiB2 particles increased. The electrical and thermal conductivities of Mg-TiB2 nanocomposites decreased at a higher rate for a higher weight fraction of nano-TiB2 particles. The experimental electrical and thermal conductivities of Mg-TiB2 nanocomposites at a certain amount of nano-TiB2 particles was measured at lower values than those obtained by analytical calculations. The compressive strength of Mg-TiB2 nanocomposites was higher than that of monolithic Mg and improved as the weight fraction of nano-TiB2 particles increased; however, a high amount of nano-TiB2 particles resulted in a decrease in compressive strength. The compressive strength of Mg-TiB2 nanocomposite with 1.5wt.% nano-TiB2 particles improved by 34%; on the other hand, its failure strain decreased by 12% compared to monolithic Mg.
- 30 December 2021
- Published by Marmara University in International Journal of Advances in Engineering and Pure Sciences
- Vol. 33 (4) , 526-536
Electrical, Thermal, and Mechanical Properties of Mg-TiB2 Nanocomposites Produced by Spark Plasma Sintering
Monolithic magnesium was reinforced with nano-TiB2 particles to produce Mg-TiB2 nanocomposites, and the effects of nano-TiB2 particles on the electrical, thermal, and mechanical properties of Mg matrix nanocomposites were studied. Monolithic Mg and Mg-TiB2 nanocomposites were manufactured using spark plasma sintering process. Both analytical and experimental findings revealed that the electrical and thermal conductivities of Mg-TiB2 nanocomposites were lower than those of monolithic Mg and decreased as the amount of nano-TiB2 particles increased. The electrical and thermal conductivities of Mg-TiB2 nanocomposites decreased at a higher rate for a higher weight fraction of nano-TiB2 particles. The experimental electrical and thermal conductivities of Mg-TiB2 nanocomposites at a certain amount of nano-TiB2 particles was measured at lower values than those obtained by analytical calculations. The compressive strength of Mg-TiB2 nanocomposites was higher than that of monolithic Mg and improved as the weight fraction of nano-TiB2 particles increased; however, a high amount of nano-TiB2 particles resulted in a decrease in compressive strength. The compressive strength of Mg-TiB2 nanocomposite with 1.5wt.% nano-TiB2 particles improved by 34%; on the other hand, its failure strain decreased by 12% compared to monolithic Mg.
- 18 September 2021
- Published by Gumushane University Journal of Science and Technology Institute in Gümüşhane Üniversitesi Fen Bilimleri Enstitüsü Dergisi
Comparison of the effects of microwave and spark plasma sintering on the electrical, thermal, and mechanical properties of Cu-LaB6 nanocomposites
Çalışmada, nano lantan heksaborid (LaB6) partiküllerinin, mikrodalga sinterleme (MS) ve kıvılcım plazma sinterleme (SPS) işlemleri kullanılarak üretilen bakır esaslı nanokompozitlerin (Cu-LaB6) elektriksel, ısıl ve mekanik özellikleri üzerine etkileri araştırılmıştır. Nano LaB6 partikülleri, MS ve SPS ile üretilen Cu matrisli nanokompozitlerin elektrik iletkenliğini sırasıyla % 20 ve % 13 oranında azalmasına neden olmuştur. Cu-LaB6 nanokompozitleri, takviyesiz Cu'dan daha düşük termal iletkenliğe sahip olmuştur. SPS metodu ile üretilen Cu-LaB6 nanokompozitinin elektriksel ve ısıl iletkenlikleri, MS ile üretilen Cu-LaB6 nanokompozitinden daha yüksek olmuştur. Nanokompozitlerin ısıl iletkenliğini elektriksel iletkenliklerinden hesaplayabilmek için partikül hacim oranını ve gözenekliliği dikkate alan bir denklem geliştirilmiştir. Cu-LaB6 nanokompozitler için hesaplanan ısıl iletkenlik değerleri deneysel sonuçlara oldukça yakın sonuçlar vermiştir. Cu-LaB6 nanokompozitleri, takviye edilmemiş Cu malzemelere göre sırasıyla % 49 ve % 38 oranında daha yüksek sertliğe ve basma dayanımına sahip olmuştur. SPS yöntemi ile üretilen Cu-LaB6 nanokompozitinin sertliği ve basma dayanımı, MS ile üretilen Cu-LaB6 nanokompozitinden daha yüksek olmuştur. Nano LaB6 partiküllerinin, Cu'nun elektriksel ve ısıl iletkenliklerinin bir miktar düşmesine neden olmasına rağmen, nano LaB6 partikülleri ile SPS işleminin olumlu etkileri biraraya getirilerek, yüksek sertlik ve basma dayanımına sahip Cu-LaB6 nanokompozit üretilmiştir. The effects of lanthanum hexaboride (LaB6) nano-particles on the electrical, thermal, and mechanical properties of copper-based nanocomposites (Cu-LaB6) produced using microwave sintering (MS) and spark plasma sintering (SPS) processes were investigated in this study. Nano LaB6 particles reduced the electrical conductivity of Cu matrix nanocomposites produced via MS and SPS by 20% and 13%, respectively. Cu-LaB6 nanocomposites had lower thermal conductivity than unreinforced Cu. The electrical and thermal conductivities of the Cu-LaB6 nanocomposite produced by the SPS process were higher than those of the Cu-LaB6 nanocomposite produced by the MS process. An equation that takes particle volume ratio and porosity into account was developed to predict the thermal conductivity of nanocomposites from their electrical conductivity. The calculated thermal conductivity values for Cu-LaB6 nanocomposites were very close to the experimental results. Cu-LaB6 nanocomposites had much higher hardness and compressive strength by 49% and 38%, respectively, compared to those of unreinforced Cu. The hardness and compressive strength of the Cu-LaB6 nanocomposite produced by SPS were higher than those of the Cu-LaB6 nanocomposite manufactured via MS. Although nano LaB6 reinforcement particles reduced the electrical and thermal conductivities of Cu, Cu-LaB6 nanocomposite having high hardness and compressive strength were produced by combining the positive influences of nano LaB6 reinforcement particles and the SPS process.
- 18 September 2021
- Published by Gumushane University Journal of Science and Technology Institute in Gümüşhane Üniversitesi Fen Bilimleri Enstitüsü Dergisi
Comparison of the effects of microwave and spark plasma sintering on the electrical, thermal, and mechanical properties of Cu-LaB6 nanocomposites
Çalışmada, nano lantan heksaborid (LaB6) partiküllerinin, mikrodalga sinterleme (MS) ve kıvılcım plazma sinterleme (SPS) işlemleri kullanılarak üretilen bakır esaslı nanokompozitlerin (Cu-LaB6) elektriksel, ısıl ve mekanik özellikleri üzerine etkileri araştırılmıştır. Nano LaB6 partikülleri, MS ve SPS ile üretilen Cu matrisli nanokompozitlerin elektrik iletkenliğini sırasıyla % 20 ve % 13 oranında azalmasına neden olmuştur. Cu-LaB6 nanokompozitleri, takviyesiz Cu'dan daha düşük termal iletkenliğe sahip olmuştur. SPS metodu ile üretilen Cu-LaB6 nanokompozitinin elektriksel ve ısıl iletkenlikleri, MS ile üretilen Cu-LaB6 nanokompozitinden daha yüksek olmuştur. Nanokompozitlerin ısıl iletkenliğini elektriksel iletkenliklerinden hesaplayabilmek için partikül hacim oranını ve gözenekliliği dikkate alan bir denklem geliştirilmiştir. Cu-LaB6 nanokompozitler için hesaplanan ısıl iletkenlik değerleri deneysel sonuçlara oldukça yakın sonuçlar vermiştir. Cu-LaB6 nanokompozitleri, takviye edilmemiş Cu malzemelere göre sırasıyla % 49 ve % 38 oranında daha yüksek sertliğe ve basma dayanımına sahip olmuştur. SPS yöntemi ile üretilen Cu-LaB6 nanokompozitinin sertliği ve basma dayanımı, MS ile üretilen Cu-LaB6 nanokompozitinden daha yüksek olmuştur. Nano LaB6 partiküllerinin, Cu'nun elektriksel ve ısıl iletkenliklerinin bir miktar düşmesine neden olmasına rağmen, nano LaB6 partikülleri ile SPS işleminin olumlu etkileri biraraya getirilerek, yüksek sertlik ve basma dayanımına sahip Cu-LaB6 nanokompozit üretilmiştir. The effects of lanthanum hexaboride (LaB6) nano-particles on the electrical, thermal, and mechanical properties of copper-based nanocomposites (Cu-LaB6) produced using microwave sintering (MS) and spark plasma sintering (SPS) processes were investigated in this study. Nano LaB6 particles reduced the electrical conductivity of Cu matrix nanocomposites produced via MS and SPS by 20% and 13%, respectively. Cu-LaB6 nanocomposites had lower thermal conductivity than unreinforced Cu. The electrical and thermal conductivities of the Cu-LaB6 nanocomposite produced by the SPS process were higher than those of the Cu-LaB6 nanocomposite produced by the MS process. An equation that takes particle volume ratio and porosity into account was developed to predict the thermal conductivity of nanocomposites from their electrical conductivity. The calculated thermal conductivity values for Cu-LaB6 nanocomposites were very close to the experimental results. Cu-LaB6 nanocomposites had much higher hardness and compressive strength by 49% and 38%, respectively, compared to those of unreinforced Cu. The hardness and compressive strength of the Cu-LaB6 nanocomposite produced by SPS were higher than those of the Cu-LaB6 nanocomposite manufactured via MS. Although nano LaB6 reinforcement particles reduced the electrical and thermal conductivities of Cu, Cu-LaB6 nanocomposite having high hardness and compressive strength were produced by combining the positive influences of nano LaB6 reinforcement particles and the SPS process.
- 1 July 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 236 (5) , 2499-2509
Effect of quasi-static and intermediate strain rates on the tensile properties of hybrid polymer composites
This study presents the results of an investigation on the tensile behaviour of hybrid polymer composites under different strain rates. Glass/carbon, aramid/carbon, glass/aramid, and glass/aramid/carbon hybrid laminates were produced using vacuum assisted resin transfer molding method with epoxy resin system. Uniaxial tensile testing was performed to determine the tensile strength, modulus and failure strain of the hybrid laminates under quasi static (0.001 s‒1) and intermediate (5 and 10 s‒1) strain rates. Tensile strength and elastic modulus of hybrid composites increased with increasing the strain rate. Hybrid laminates with glass fibre were more sensitive to the strain rate. Carbon layers located at the centre of the hybrid laminates resulted in increased tensile strength, indicating the major role of stacking sequence on the behaviour of hybrid composites. Scanning electron microscope (SEM) was used to examine the fracture surfaces of the laminates. The extent of damage propagation was significantly broader at intermediate strain rates.
- 1 July 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 236 (5) , 2499-2509
Effect of quasi-static and intermediate strain rates on the tensile properties of hybrid polymer composites
This study presents the results of an investigation on the tensile behaviour of hybrid polymer composites under different strain rates. Glass/carbon, aramid/carbon, glass/aramid, and glass/aramid/carbon hybrid laminates were produced using vacuum assisted resin transfer molding method with epoxy resin system. Uniaxial tensile testing was performed to determine the tensile strength, modulus and failure strain of the hybrid laminates under quasi static (0.001 s‒1) and intermediate (5 and 10 s‒1) strain rates. Tensile strength and elastic modulus of hybrid composites increased with increasing the strain rate. Hybrid laminates with glass fibre were more sensitive to the strain rate. Carbon layers located at the centre of the hybrid laminates resulted in increased tensile strength, indicating the major role of stacking sequence on the behaviour of hybrid composites. Scanning electron microscope (SEM) was used to examine the fracture surfaces of the laminates. The extent of damage propagation was significantly broader at intermediate strain rates.
- 28 April 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 235 (9) , 2036-2055
Microstructure and mechanical properties of Al–Si–Cu–Fe alloy-based ceramic particle-reinforced nanocomposites and microcomposites and a modified model to predict the yield strength of nanocomposites
The effects of volume fraction, size, and type of reinforcement particles on the microstructure and mechanical properties of Al–Si–Cu–(Fe) alloy matrix composites were investigated and an analytical model was modified to predict the yield strength of the particle-reinforced nanocomposites. Nano- and micro-particle-reinforced Al–Si–Cu-(Fe) matrix composites (N-AMCs and M-AMCs) were manufactured by adding two different types and sizes of reinforcement particles to Al–Si–Cu–(Fe) alloys at different volume fractions using a two-step stir casting method combined with a high-energy ball milling process and a high-pressure die-casting method. Microstructural analyzes of N-AMCs and M-AMCs were performed using SEM, EDX, and XRD. The Brinell hardness test and the tensile test were carried out to determine the mechanical properties of the N-AMCs and M-AMCs. The hardness of the N-AMCs and M-AMCs was continuously enhanced by increasing the volume fraction of the reinforcement particles, while the yield strength and ultimate tensile strength of the N-AMCs and M-AMCs were improved up to 1.5 vol.% and 4 vol.% of nano-particles and micro-particles, respectively. An analytical model was modified to predict the yield strength of N-AMCs by integrating the effective volume ratio of nano-particles into each strengthening mechanism. The results predicted by the modified model reached nearly 98% agreement with the experimental results up to 1.5 vol.% of the reinforcement particles. Nano-particles had a much greater effect on strengthening mechanisms compared to micro-particles.
- 28 April 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 235 (9) , 2036-2055
Microstructure and mechanical properties of Al–Si–Cu–Fe alloy-based ceramic particle-reinforced nanocomposites and microcomposites and a modified model to predict the yield strength of nanocomposites
The effects of volume fraction, size, and type of reinforcement particles on the microstructure and mechanical properties of Al–Si–Cu–(Fe) alloy matrix composites were investigated and an analytical model was modified to predict the yield strength of the particle-reinforced nanocomposites. Nano- and micro-particle-reinforced Al–Si–Cu-(Fe) matrix composites (N-AMCs and M-AMCs) were manufactured by adding two different types and sizes of reinforcement particles to Al–Si–Cu–(Fe) alloys at different volume fractions using a two-step stir casting method combined with a high-energy ball milling process and a high-pressure die-casting method. Microstructural analyzes of N-AMCs and M-AMCs were performed using SEM, EDX, and XRD. The Brinell hardness test and the tensile test were carried out to determine the mechanical properties of the N-AMCs and M-AMCs. The hardness of the N-AMCs and M-AMCs was continuously enhanced by increasing the volume fraction of the reinforcement particles, while the yield strength and ultimate tensile strength of the N-AMCs and M-AMCs were improved up to 1.5 vol.% and 4 vol.% of nano-particles and micro-particles, respectively. An analytical model was modified to predict the yield strength of N-AMCs by integrating the effective volume ratio of nano-particles into each strengthening mechanism. The results predicted by the modified model reached nearly 98% agreement with the experimental results up to 1.5 vol.% of the reinforcement particles. Nano-particles had a much greater effect on strengthening mechanisms compared to micro-particles.