Christiane Bauer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Christiane Bauer has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Caroline Willich
Institute for Energy Conversion and Storage, Ulm University, Albert-Einstein-Allee 47, 89081 Ulm, Germany
13 shared publications - Daniel Frank
Institute for Energy Conversion and Storage, Ulm University, Albert-Einstein-Allee 47, 89081 Ulm, Germany
5 shared publications - Josef Kallo
Institute for Energy Conversion and Storage, Ulm University, Albert-Einstein-Allee 47, 89081 Ulm, Germany
5 shared publications - Tobias Graf
Institute for Energy Conversion and Storage, Ulm University, Albert-Einstein-Allee 47, 89081 Ulm, Germany
5 shared publications - Pia Hoenicke
Institute for Energy Conversion and Storage, Ulm University
4 shared publications Josef Kallo
3 shared publications
Latest Publications
- Open Access
High-Altitude Operation of a Commercial 100 kW PEM Fuel Cell System
A commercially available 100 kW PEM fuel cell system designed for efficient operation on ground-level was tested at low ambient pressures between 750 mbar and 940 mbar in a low-pressure chamber. The current–voltage characteristics at 940 mbar and 900 mbar showed only small differences, while the system performed worse at lower ambient pressures. To enable operation at these low pressures, an additional current-limiting strategy had to be implemented, as it was found that the compressor could not deliver sufficient mass flow at ambient pressures below 867 mbar to reach the maximum current allowed by the system (420 A). The results show that the fuel cell system, which was designed for ground-level applications, can be operated at lower pressures if the proposed current-limiting strategy is implemented, although at the cost of a lower maximum current output at low ambient pressures. Based on the results, suggestions for further hardware measures to optimise the system for flight conditions are made.
Open AccessHigh-Altitude Operation of a Commercial 100 kW PEM Fuel Cell System
A commercially available 100 kW PEM fuel cell system designed for efficient operation on ground-level was tested at low ambient pressures between 750 mbar and 940 mbar in a low-pressure chamber. The current–voltage characteristics at 940 mbar and 900 mbar showed only small differences, while the system performed worse at lower ambient pressures. To enable operation at these low pressures, an additional current-limiting strategy had to be implemented, as it was found that the compressor could not deliver sufficient mass flow at ambient pressures below 867 mbar to reach the maximum current allowed by the system (420 A). The results show that the fuel cell system, which was designed for ground-level applications, can be operated at lower pressures if the proposed current-limiting strategy is implemented, although at the cost of a lower maximum current output at low ambient pressures. Based on the results, suggestions for further hardware measures to optimise the system for flight conditions are made.
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (26) , 2059
Model-Based Development of Control Strategies for a Fuel Cell Air Supply System and Experimental Verification at Flight-Relevant Conditions
The performance of hydrogen PEM fuel cell systems can be optimized by means of pressurization of the cathode air, especially in aviation, where at in-flight conditions the pressure of the ambient air is significantly lower as at on-ground conditions. To provide the inlet air at optimal conditions (p, T, rH) during flight, an air supply system is required and in an all-electric aircraft the compression should happen by means of an electric centrifugal compressor. A challenge for the operation of a pressurised fuel cell system at high altitudes is the control of the compression system. Any unstable operation like compressor surge has to be avoided, since it can damage both the fuel cell stack and the compressor itself. For the development of such an air supply system, a combined experimental and modeling approach was chosen. A hydrogen PEM fuel cell system was characterized at nominal and at low cathode pressures to obtain the behavior at flight relevant conditions and an experimental air supply system containing electric compressor, intercooler, humidifier, cathode volume and throttle valve at the outlet has been set up and used for the development, parameterization, and validation of a model for the compression system. The model is based on the Greitzer model 1,2, and has been extended to also represent the additional components between the compressor and the throttle valve (intercooler, humidifier, and cathode volume) 3. It is now able to predict the transient response of the entire air supply system to changes in the reference values of compressor speed and valve opening angle and the resulting mass flow changes and pressures within the individual components. The model and the data from the fuel cell system were used for the development of improved control strategies, that make it possible to operate the system safely in a wide range of operating conditions. Unstable situations, like compressor surge, are avoided by these control strategies even in the highly varying conditions during a flight. The developed control strategies are verified on the hardware of the experimental setup and tested under realistic flight conditions in a low-pressure climate chamber. References Greitzer, E. M. Surge and Rotating Stall in Axial Flow Compressors—Part I: Theoretical Compression System Model. Journal of Engineering for Power 98, 190–198 (1976). Gravdahl, J. T. & Egeland, O. Compressor Surge and Rotating Stall. (Springer London, London, 1999). doi:10.1007/978-1-4471-0827-6. Frank, D., Bauer, C. & Willich, C. Modeling of the cathode air supply for a pressurized hydrogen fuel cell system in airborne applications. Proceedings of the Aerospace Europe Conference 2023 (2023) doi:10.13009/EUCASS2023-218.
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (26) , 2059
Model-Based Development of Control Strategies for a Fuel Cell Air Supply System and Experimental Verification at Flight-Relevant Conditions
The performance of hydrogen PEM fuel cell systems can be optimized by means of pressurization of the cathode air, especially in aviation, where at in-flight conditions the pressure of the ambient air is significantly lower as at on-ground conditions. To provide the inlet air at optimal conditions (p, T, rH) during flight, an air supply system is required and in an all-electric aircraft the compression should happen by means of an electric centrifugal compressor. A challenge for the operation of a pressurised fuel cell system at high altitudes is the control of the compression system. Any unstable operation like compressor surge has to be avoided, since it can damage both the fuel cell stack and the compressor itself. For the development of such an air supply system, a combined experimental and modeling approach was chosen. A hydrogen PEM fuel cell system was characterized at nominal and at low cathode pressures to obtain the behavior at flight relevant conditions and an experimental air supply system containing electric compressor, intercooler, humidifier, cathode volume and throttle valve at the outlet has been set up and used for the development, parameterization, and validation of a model for the compression system. The model is based on the Greitzer model 1,2, and has been extended to also represent the additional components between the compressor and the throttle valve (intercooler, humidifier, and cathode volume) 3. It is now able to predict the transient response of the entire air supply system to changes in the reference values of compressor speed and valve opening angle and the resulting mass flow changes and pressures within the individual components. The model and the data from the fuel cell system were used for the development of improved control strategies, that make it possible to operate the system safely in a wide range of operating conditions. Unstable situations, like compressor surge, are avoided by these control strategies even in the highly varying conditions during a flight. The developed control strategies are verified on the hardware of the experimental setup and tested under realistic flight conditions in a low-pressure climate chamber. References Greitzer, E. M. Surge and Rotating Stall in Axial Flow Compressors—Part I: Theoretical Compression System Model. Journal of Engineering for Power 98, 190–198 (1976). Gravdahl, J. T. & Egeland, O. Compressor Surge and Rotating Stall. (Springer London, London, 1999). doi:10.1007/978-1-4471-0827-6. Frank, D., Bauer, C. & Willich, C. Modeling of the cathode air supply for a pressurized hydrogen fuel cell system in airborne applications. Proceedings of the Aerospace Europe Conference 2023 (2023) doi:10.13009/EUCASS2023-218.
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (25) , 2047
Pressurizing the Fuel Cell in a Direct Hybrid System for Airborne Applications
The push towards achieving emission-free aviation is intensifying. The number of demonstrator aircraft like the HY4 form H2FLY or the ATR72 from Universal Hydrogen taking flight and gaining experience in electric aviation is increasing. One existing approach for the realization of an all-electric aircraft is a direct hybrid system comprising a fuel cell and a battery. During high-power phases of a mission, such as takeoff and climb, both the battery and the fuel cell contribute power. However, during cruise, power is solely supplied by the fuel cell to leverage the high energy density of hydrogen. In a direct hybrid system, the power share of the fuel cell and the battery is determined by the size and the operating conditions of both. The low ambient pressures at high altitude negatively affect the performance of fuel cells. This is not only important in fuel cell only propulsion systems but also when operating a direct hybrid system. The impact of low pressures on the behavior of a direct hybrid system, linking a fuel cell and a battery without a DC/DC converter, is demonstrated. The effects of a non-pressurized PEM-fuel cell in a direct hybrid with a lithium-ion battery in a low-pressure environment was analyzed previously (see attached figure). However, since weight and volume are crucial factors in an aircraft, the fuel cell reactants can be pressurized to increase the power density of the system. Pressurization improves the fuel cells performance and therefore reduces weight and volume of the system, but the pressurization of the ambient air to the desired inlet pressure of the fuel cell cathode requires energy. The pressurization of a fuel cell also changes its voltage power behavior, which in turn affects the operation of the direct hybrid system. In order to examine and analyze the influence of pressurization on the overall system performance, an open-source two-phase model of a fuel cell is used and compared to experimental measurement data to gain fuel cell data at different pressure levels. The behavior of the direct hybrid system at different operating conditions will be presented, where the net power of the pressurized PEM-fuel cell system is combined with a battery to form a direct hybrid system. At lower state of charge (SOC) levels, the share of the fuel cell increases due to the lower voltage level of the battery over all power levels. In a pressure-driven fuel cell system, we take advantage of the fact that the pressure of the reactants can be controlled. By adjusting the pressure, the power share of the fuel cell and battery can be actively controlled. Lower operating pressure results in a higher battery share, due to the lower fuel cell voltage. By increasing the pressure, the voltage level provided by the fuel cell increases and therefore the power share of the fuel cell also increases. In addition, a realistic flight mission is analyzed with a constant compression ratio for the fuel cell air supply resulting in variable operating pressures of the fuel cell during flight, due to the different environmental pressures. The performance of the pressurized fuel cell direct hybrid under those varying ambient conditions will be presented. Figure 1
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (25) , 2047
Pressurizing the Fuel Cell in a Direct Hybrid System for Airborne Applications
The push towards achieving emission-free aviation is intensifying. The number of demonstrator aircraft like the HY4 form H2FLY or the ATR72 from Universal Hydrogen taking flight and gaining experience in electric aviation is increasing. One existing approach for the realization of an all-electric aircraft is a direct hybrid system comprising a fuel cell and a battery. During high-power phases of a mission, such as takeoff and climb, both the battery and the fuel cell contribute power. However, during cruise, power is solely supplied by the fuel cell to leverage the high energy density of hydrogen. In a direct hybrid system, the power share of the fuel cell and the battery is determined by the size and the operating conditions of both. The low ambient pressures at high altitude negatively affect the performance of fuel cells. This is not only important in fuel cell only propulsion systems but also when operating a direct hybrid system. The impact of low pressures on the behavior of a direct hybrid system, linking a fuel cell and a battery without a DC/DC converter, is demonstrated. The effects of a non-pressurized PEM-fuel cell in a direct hybrid with a lithium-ion battery in a low-pressure environment was analyzed previously (see attached figure). However, since weight and volume are crucial factors in an aircraft, the fuel cell reactants can be pressurized to increase the power density of the system. Pressurization improves the fuel cells performance and therefore reduces weight and volume of the system, but the pressurization of the ambient air to the desired inlet pressure of the fuel cell cathode requires energy. The pressurization of a fuel cell also changes its voltage power behavior, which in turn affects the operation of the direct hybrid system. In order to examine and analyze the influence of pressurization on the overall system performance, an open-source two-phase model of a fuel cell is used and compared to experimental measurement data to gain fuel cell data at different pressure levels. The behavior of the direct hybrid system at different operating conditions will be presented, where the net power of the pressurized PEM-fuel cell system is combined with a battery to form a direct hybrid system. At lower state of charge (SOC) levels, the share of the fuel cell increases due to the lower voltage level of the battery over all power levels. In a pressure-driven fuel cell system, we take advantage of the fact that the pressure of the reactants can be controlled. By adjusting the pressure, the power share of the fuel cell and battery can be actively controlled. Lower operating pressure results in a higher battery share, due to the lower fuel cell voltage. By increasing the pressure, the voltage level provided by the fuel cell increases and therefore the power share of the fuel cell also increases. In addition, a realistic flight mission is analyzed with a constant compression ratio for the fuel cell air supply resulting in variable operating pressures of the fuel cell during flight, due to the different environmental pressures. The performance of the pressurized fuel cell direct hybrid under those varying ambient conditions will be presented. Figure 1
- Open Access
Optimal Sizing of Fuel Cell and Battery in a Direct-Hybrid for Electric Aircraft
The climate impact of aviation can be reduced using powertrains based on hydrogen fuel cells and batteries. Combining both technologies in a direct-hybrid without a DC/DC converter is a promising approach for light-weight systems. Depending on the power demand, both the fuel cell and battery are used to provide power or only the fuel cell is connected to the powertrain. The system voltage in a direct-hybrid is determined by the fuel cell and battery, but the performance of fuel cells is affected by low-ambient pressure at high altitudes and the battery voltage is affected by state of charge and discharge rate. Taking this into account, the presented work demonstrates how a direct-hybrid system must be designed based on a scaled mission profile of a 40-seater aircraft. The fuel cell and battery are configured and sized according to the power demand in different flight phases while considering voltage limits given by the powertrain. The energy requirement from the fuel cell and the battery is calculated for a flight based on a realistic mission profile and different battery and fuel cell configurations are evaluated. By optimizing the battery and fuel cell size, the energy required from the battery was reduced by 57% and the total weight of the fuel cell and battery was reduced by 11%.
Open AccessOptimal Sizing of Fuel Cell and Battery in a Direct-Hybrid for Electric Aircraft
The climate impact of aviation can be reduced using powertrains based on hydrogen fuel cells and batteries. Combining both technologies in a direct-hybrid without a DC/DC converter is a promising approach for light-weight systems. Depending on the power demand, both the fuel cell and battery are used to provide power or only the fuel cell is connected to the powertrain. The system voltage in a direct-hybrid is determined by the fuel cell and battery, but the performance of fuel cells is affected by low-ambient pressure at high altitudes and the battery voltage is affected by state of charge and discharge rate. Taking this into account, the presented work demonstrates how a direct-hybrid system must be designed based on a scaled mission profile of a 40-seater aircraft. The fuel cell and battery are configured and sized according to the power demand in different flight phases while considering voltage limits given by the powertrain. The energy requirement from the fuel cell and the battery is calculated for a flight based on a realistic mission profile and different battery and fuel cell configurations are evaluated. By optimizing the battery and fuel cell size, the energy required from the battery was reduced by 57% and the total weight of the fuel cell and battery was reduced by 11%.
- Open Access
Switching Logic for a Direct Hybrid Electric Powertrain
Hybrid electric aircraft with a powertrain based on fuel cells and batteries can reduce climate-active emissions in aviation. In a direct hybrid powertrain, the fuel cell and the battery are connected in parallel, without a DC/DC converter balancing their voltage levels. Switches make it possible to select different operational modes (fuel cell only, hybrid or battery charging) depending on the power demand during different flight phases. To exploit the high specific energy of hydrogen, the system should change from Hybrid Mode during take-off to Fuel Cell Mode in cruise. During descent, the battery can be charged if Charging Mode is selected. To avoid voltage and current peaks and consequent damage to components when switching between modes, certain conditions must be fulfilled. Those switching conditions were defined, and switching procedures for changing from one mode to the other during flight were developed and tested in a lab system. In a direct hybrid, the system voltage depends on the required power. When switching from Hybrid Mode to Fuel Cell Mode, a short reduction in power of 65% is necessary for the examined system to meet the switching requirements. It is also shown how this power loss can be reduced to 25% by distributed propulsion with a second powertrain or even eliminated by a change in the hybrid ratio.
Open AccessSwitching Logic for a Direct Hybrid Electric Powertrain
Hybrid electric aircraft with a powertrain based on fuel cells and batteries can reduce climate-active emissions in aviation. In a direct hybrid powertrain, the fuel cell and the battery are connected in parallel, without a DC/DC converter balancing their voltage levels. Switches make it possible to select different operational modes (fuel cell only, hybrid or battery charging) depending on the power demand during different flight phases. To exploit the high specific energy of hydrogen, the system should change from Hybrid Mode during take-off to Fuel Cell Mode in cruise. During descent, the battery can be charged if Charging Mode is selected. To avoid voltage and current peaks and consequent damage to components when switching between modes, certain conditions must be fulfilled. Those switching conditions were defined, and switching procedures for changing from one mode to the other during flight were developed and tested in a lab system. In a direct hybrid, the system voltage depends on the required power. When switching from Hybrid Mode to Fuel Cell Mode, a short reduction in power of 65% is necessary for the examined system to meet the switching requirements. It is also shown how this power loss can be reduced to 25% by distributed propulsion with a second powertrain or even eliminated by a change in the hybrid ratio.
- Open Access
- 1 June 2023
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 170 (6) , 060541
Influence of Low Pressures on the Performance of Lithium Ion Batteries for Airplane Applications
The electrification of aircrafts is a recent trend in aviation and with it the use of batteries as energy carriers at high altitudes. These batteries can be exposed to low pressures and it is crucial to understand the influence of low pressures on the battery behavior. In this study, commercially available lithium ion batteries were examined experimentally at low pressures down to 25 kPa. Discharge curves and impedance measurements were performed at 23 °C for each pressure level. Cylindrical Lithium Nickel-Cobalt-Aluminum Oxide (NCA) and Iron-Phosphate (LFP) cells did not show any pressure influence, while Lithium Nickel-Manganese-Cobalt Oxide (NMC) pouch cells showed some performance variation with reduced pressure. The ohmic resistance increased by around 0.1 mΩ per 25 kPa and at 25 kPa the charge transfer impedance increased for low SOCs. The results show that no strong change in performance is to be expected for low pressure applications in airplanes, however further research is needed with respect to long term effects, thermal management and safety.
- 1 June 2023
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 170 (6) , 060541
Open AccessInfluence of Low Pressures on the Performance of Lithium Ion Batteries for Airplane Applications
The electrification of aircrafts is a recent trend in aviation and with it the use of batteries as energy carriers at high altitudes. These batteries can be exposed to low pressures and it is crucial to understand the influence of low pressures on the battery behavior. In this study, commercially available lithium ion batteries were examined experimentally at low pressures down to 25 kPa. Discharge curves and impedance measurements were performed at 23 °C for each pressure level. Cylindrical Lithium Nickel-Cobalt-Aluminum Oxide (NCA) and Iron-Phosphate (LFP) cells did not show any pressure influence, while Lithium Nickel-Manganese-Cobalt Oxide (NMC) pouch cells showed some performance variation with reduced pressure. The ohmic resistance increased by around 0.1 mΩ per 25 kPa and at 25 kPa the charge transfer impedance increased for low SOCs. The results show that no strong change in performance is to be expected for low pressure applications in airplanes, however further research is needed with respect to long term effects, thermal management and safety.
- Open Access
- 17 November 2022
- Published by Elsevier in Journal of Energy Storage
- Vol. 56
Investigation of a fuel cell hybrid system with a new modular test bench approach for all electric hybrid power train systems
- 17 November 2022
- Published by Elsevier in Journal of Energy Storage
- Vol. 56
Open AccessInvestigation of a fuel cell hybrid system with a new modular test bench approach for all electric hybrid power train systems
- 9 October 2022
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2022-02 (3) , 217
Influence of Aviation Conditions on Lithium-Ion Batteries
Stopping climate change and global temperature rise needs a determined course of action in several technology fields and the development of ZERO-CO2 aircrafts and low emission battery-ICE aircrafts, as well. Batteries in hybrid-electric or fully-electric aircrafts are an option to decrease emissions. The battery requirements for the aviation sector regarding specific energy, energy density and safety are high. Lithium-ion batteries are today the only commercially available technology to meet these requirements, but adequate technology readiness is only proven for the automobile sector while TRL levels 8 and 9 for implementation readiness of batteries in the aviation sector is still ongoing. A crucial aspect for aviation applications is the operation behavior in high altitude including low temperature, wide humidity ranges and especially low pressure. There is little published information available on the effects of low pressure on battery performance. Therefore, different commercially available lithium-ion batteries were tested from atmospheric pressure down to 250 hPa, which corresponds to a flight altitude up to 10,000 m, according to the International Standard Atmosphere (ISA). Since NMC and NCA cathode materials are promising for aviation due to their high specific energy, and LFP cells are promising because of their high safety, the following batteries were selected: 20 Ah HP602030 LFP cylindrical cell (EAS Batteries GmbH, GER). 10 Ah HE 341440 NCA cylindrical cell (EAS Batteries GmbH, GER). 12 Ah SLPB065070180 NMC pouch cell (Kokam Co. Ltd., KOR) To examine the influence of pressure on the battery behavior, constant current discharge tests at 1C 0.5C and 2C rates as well as impedance measurements in 10% SOC steps were performed in a climate controlled low-pressure chamber. The batteries were operated under different temperatures and in controlled low pressure. The pressure was first set to atmospheric pressure as a reference and then lowered to 750 hPa, 500 hPa and 250 hPa. To further examine altitude influences, current cycles and impedance spectroscopy were performed at different temperature and humidity values. The behavior of the cylindrical cells showed hardly any pressure dependency, while the examined pouch cell’s behavior did show a pressure dependency. All batteries showed strong temperature dependency but hardly any humidity dependency. In this presentation the influence of pressure, temperature and humidity on voltage, capacity, resistance and impedance of the afore mentioned batteries will be discussed. The batteries are compared regarding their aviation applicability with special respect to low pressure. The parameters for each environmental condition can then be used to parameterize a battery model suitable for aviation applications.
- 9 October 2022
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2022-02 (3) , 217
Influence of Aviation Conditions on Lithium-Ion Batteries
Stopping climate change and global temperature rise needs a determined course of action in several technology fields and the development of ZERO-CO2 aircrafts and low emission battery-ICE aircrafts, as well. Batteries in hybrid-electric or fully-electric aircrafts are an option to decrease emissions. The battery requirements for the aviation sector regarding specific energy, energy density and safety are high. Lithium-ion batteries are today the only commercially available technology to meet these requirements, but adequate technology readiness is only proven for the automobile sector while TRL levels 8 and 9 for implementation readiness of batteries in the aviation sector is still ongoing. A crucial aspect for aviation applications is the operation behavior in high altitude including low temperature, wide humidity ranges and especially low pressure. There is little published information available on the effects of low pressure on battery performance. Therefore, different commercially available lithium-ion batteries were tested from atmospheric pressure down to 250 hPa, which corresponds to a flight altitude up to 10,000 m, according to the International Standard Atmosphere (ISA). Since NMC and NCA cathode materials are promising for aviation due to their high specific energy, and LFP cells are promising because of their high safety, the following batteries were selected: 20 Ah HP602030 LFP cylindrical cell (EAS Batteries GmbH, GER). 10 Ah HE 341440 NCA cylindrical cell (EAS Batteries GmbH, GER). 12 Ah SLPB065070180 NMC pouch cell (Kokam Co. Ltd., KOR) To examine the influence of pressure on the battery behavior, constant current discharge tests at 1C 0.5C and 2C rates as well as impedance measurements in 10% SOC steps were performed in a climate controlled low-pressure chamber. The batteries were operated under different temperatures and in controlled low pressure. The pressure was first set to atmospheric pressure as a reference and then lowered to 750 hPa, 500 hPa and 250 hPa. To further examine altitude influences, current cycles and impedance spectroscopy were performed at different temperature and humidity values. The behavior of the cylindrical cells showed hardly any pressure dependency, while the examined pouch cell’s behavior did show a pressure dependency. All batteries showed strong temperature dependency but hardly any humidity dependency. In this presentation the influence of pressure, temperature and humidity on voltage, capacity, resistance and impedance of the afore mentioned batteries will be discussed. The batteries are compared regarding their aviation applicability with special respect to low pressure. The parameters for each environmental condition can then be used to parameterize a battery model suitable for aviation applications.
- Open Access
A Flexible DC–DC Converter with Multi-Directional Power Flow Capabilities for Power Management and Delivery Module in a Hybrid Electric Aircraft
The development of fully electric and hybrid electric aircraft using fuel cells and batteries has lately received much attention since the technology can contribute to achieving an emission-free world. For hybridisation of fuel cells and batteries, the challenge of integrating different voltage sources to supply power to different loads at different voltage levels has to be met. Presently, this is achieved by using a combination of complex passive circuitry and DC–DC converters. In this paper, a new galvanically isolated DC–DC converter topology is proposed; it integrates a battery and fuel cells as input sources and supplies power to a high voltage (HV) and a low voltage (LV) load simultaneously. The converter enables power flow from the sources to the load, as well as between the sources and power flow back towards the battery during recuperation for recharging the battery during flight. The functionality of the converter design is verified using a real-time (RT) hardware-in-the-loop (HiL) test. The proposed concept is easily scalable and can be adopted in any fuel cell and battery drive train of all-electric flights of different sizes.
Open AccessA Flexible DC–DC Converter with Multi-Directional Power Flow Capabilities for Power Management and Delivery Module in a Hybrid Electric Aircraft
The development of fully electric and hybrid electric aircraft using fuel cells and batteries has lately received much attention since the technology can contribute to achieving an emission-free world. For hybridisation of fuel cells and batteries, the challenge of integrating different voltage sources to supply power to different loads at different voltage levels has to be met. Presently, this is achieved by using a combination of complex passive circuitry and DC–DC converters. In this paper, a new galvanically isolated DC–DC converter topology is proposed; it integrates a battery and fuel cells as input sources and supplies power to a high voltage (HV) and a low voltage (LV) load simultaneously. The converter enables power flow from the sources to the load, as well as between the sources and power flow back towards the battery during recuperation for recharging the battery during flight. The functionality of the converter design is verified using a real-time (RT) hardware-in-the-loop (HiL) test. The proposed concept is easily scalable and can be adopted in any fuel cell and battery drive train of all-electric flights of different sizes.
- Open Access
Influence of Low Inlet Pressure and Temperature on the Compressor Map Limits of Electrical Turbo Chargers for Airborne Fuel Cell Applications
For the optimal high-efficiency operation of a PEM fuel cell system, the temperature, pressure, humidity and mass flow of the supplied air must be tuned to the fuel cell stack requirements. Especially for aircraft applications, this requires a thorough understanding of the fuel cell air supply system behavior and how it changes when the ambient pressure is below 1 bar(a) during flight. This work investigates the influence of low inlet pressures and varying inlet temperatures on the compression map of an electrical turbo charger. This is especially relevant in airborne fuel cell application and not much literature can be found on that topic. Compressor limits are evaluated experimentally and theoretically. The theory of mass flow and speed correction is compared to experimental findings and found to be applicable for the surge and speed limit of the investigated turbo chargers as long as the compressor map is not limited by the power of the electric motor and inverter. Based on this, a prediction of the compressor map for altitudes up to 10,000 m is made with the help of a developed software tool.
Open AccessInfluence of Low Inlet Pressure and Temperature on the Compressor Map Limits of Electrical Turbo Chargers for Airborne Fuel Cell Applications
For the optimal high-efficiency operation of a PEM fuel cell system, the temperature, pressure, humidity and mass flow of the supplied air must be tuned to the fuel cell stack requirements. Especially for aircraft applications, this requires a thorough understanding of the fuel cell air supply system behavior and how it changes when the ambient pressure is below 1 bar(a) during flight. This work investigates the influence of low inlet pressures and varying inlet temperatures on the compression map of an electrical turbo charger. This is especially relevant in airborne fuel cell application and not much literature can be found on that topic. Compressor limits are evaluated experimentally and theoretically. The theory of mass flow and speed correction is compared to experimental findings and found to be applicable for the surge and speed limit of the investigated turbo chargers as long as the compressor map is not limited by the power of the electric motor and inverter. Based on this, a prediction of the compressor map for altitudes up to 10,000 m is made with the help of a developed software tool.