Yili Hu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Yili Hu has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Sheng Chen
National Laboratory of Radar Signal Processing, Xidian University, Xi’an 710071, China
3 shared publications - Yongbo Zhao
Xidian University
3 shared publications Xiaojiao Pang
National Lab of Radar Signal Processing Xidian University Xi’an China
2 shared publications- Chenghu Cao
Xian University of Posts and Telecommunications, Xian, China
1 shared publication
Latest Publications
- Open Access
- 15 December 2021
- Published by Hindawi Limited in International Journal of Antennas and Propagation
- Vol. 2021, 1-10
Incoherent Integration Detection Method of Airborne Phased Array Radar in a Multipath Environment
Airborne phased array radar (PAR) suffers from multipath problems when flying over a calm sea surface. The existence of a multipath phenomenon will cause the electromagnetic echo of the same target to be reflected back to the airborne PAR from two paths, namely, direct path (DP) and multipath. Compared with the ground-based radar, the target echo received by airborne PAR in the multipath environment has two important characteristics: one is that the DP signal and the multipath signal exist in different range bins, and the other is that the radar cross section (RCS) in the DP direction may be smaller than that in the multipath direction. Considering these two characteristics, this paper first proposes a target pairing algorithm for matching the DP range and multipath range of the same target in signal detection, and then, combined with the cell-averaging constant false alarm rate (CA-CFAR) detection model, an incoherent integration detection method for airborne PAR in the multipath environment is proposed. In the target pairing process, the geometric structure relationship of the airborne PAR model can be fully utilized. After a successful target pairing process, the energy of the multipath signal will be incoherently accumulated into the corresponding DP range bin, so as to improve the probability of DP range bin data passing the detection threshold. In essence, the proposed method makes full use of multipath energy to improve the detection capability of airborne PAR in the multipath environment. Finally, the detection probability of the proposed method is given, and the detection performance is analyzed.
- 15 December 2021
- Published by Hindawi Limited in International Journal of Antennas and Propagation
- Vol. 2021, 1-10
Open AccessIncoherent Integration Detection Method of Airborne Phased Array Radar in a Multipath Environment
Airborne phased array radar (PAR) suffers from multipath problems when flying over a calm sea surface. The existence of a multipath phenomenon will cause the electromagnetic echo of the same target to be reflected back to the airborne PAR from two paths, namely, direct path (DP) and multipath. Compared with the ground-based radar, the target echo received by airborne PAR in the multipath environment has two important characteristics: one is that the DP signal and the multipath signal exist in different range bins, and the other is that the radar cross section (RCS) in the DP direction may be smaller than that in the multipath direction. Considering these two characteristics, this paper first proposes a target pairing algorithm for matching the DP range and multipath range of the same target in signal detection, and then, combined with the cell-averaging constant false alarm rate (CA-CFAR) detection model, an incoherent integration detection method for airborne PAR in the multipath environment is proposed. In the target pairing process, the geometric structure relationship of the airborne PAR model can be fully utilized. After a successful target pairing process, the energy of the multipath signal will be incoherently accumulated into the corresponding DP range bin, so as to improve the probability of DP range bin data passing the detection threshold. In essence, the proposed method makes full use of multipath energy to improve the detection capability of airborne PAR in the multipath environment. Finally, the detection probability of the proposed method is given, and the detection performance is analyzed.
- Open Access
- 9 June 2021
- Published by Institution of Engineering and Technology (IET) in IET Radar, Sonar & Navigation
- Vol. 15 (10) , 1173-1180
Direction of arrival estimation of airborne multiple‐input multiple‐output radar in multipath environment
Airborne multiple‐input multiple‐output (MIMO) radar can transmit orthogonal waveforms to increase the range of the detection target. However, in a multipath environment, airborne MIMO radar also has energy radiated to the target through multipath directions, which makes the multipath phenomenon of airborne MIMO radar complicated. Because the direct path signal and the multipath signals of the airborne radar are at different range gates, the characteristics of data between the direct path signal and the multipath signals of the airborne MIMO radar can be used to propose a method for estimating the reflection coefficient amplitude (RCA). Considering that the target echoes data at different range gates can be used to estimate the elevation angle of the target, a direction of arrival (DOA) estimation method using data fusion at low signal‐to‐noise ratio (SNR) is proposed. Moreover, at high SNR, the signal path corresponding to the maximum target echo power is selected for DOA estimation based on the estimated multipath RCA. The proposed method makes full use of all target echo data of airborne MIMO radar in a multipath environment and is suitable for practical applications. Finally, simulation experiments verify that the proposed method can effectively improve the DOA estimation accuracy.
- 9 June 2021
- Published by Institution of Engineering and Technology (IET) in IET Radar, Sonar & Navigation
- Vol. 15 (10) , 1173-1180
Open AccessDirection of arrival estimation of airborne multiple‐input multiple‐output radar in multipath environment
Airborne multiple‐input multiple‐output (MIMO) radar can transmit orthogonal waveforms to increase the range of the detection target. However, in a multipath environment, airborne MIMO radar also has energy radiated to the target through multipath directions, which makes the multipath phenomenon of airborne MIMO radar complicated. Because the direct path signal and the multipath signals of the airborne radar are at different range gates, the characteristics of data between the direct path signal and the multipath signals of the airborne MIMO radar can be used to propose a method for estimating the reflection coefficient amplitude (RCA). Considering that the target echoes data at different range gates can be used to estimate the elevation angle of the target, a direction of arrival (DOA) estimation method using data fusion at low signal‐to‐noise ratio (SNR) is proposed. Moreover, at high SNR, the signal path corresponding to the maximum target echo power is selected for DOA estimation based on the estimated multipath RCA. The proposed method makes full use of all target echo data of airborne MIMO radar in a multipath environment and is suitable for practical applications. Finally, simulation experiments verify that the proposed method can effectively improve the DOA estimation accuracy.
- Open Access
- 26 April 2021
- Published by Institution of Engineering and Technology (IET) in IET Radar, Sonar & Navigation
- Vol. 15 (6) , 655-665
Joint design of transmit beamspace and reduced‐dimension receiver filter for MIMO radar STAP
In this article, the problem of the transmit beamspace (TB) matrix design in multiple‐input multiple‐output (MIMO) radar is considered. To reduce the computational burden and to focus the energy within optimal spatial sector, a joint design method of the TB matrix and a reduced‐dimension space‐time adaptive processing (STAP) filter is proposed based on the maximum signal‐to‐clutter‐plus‐noise ratio (SCNR). Firstly, the signal model of the reduced‐dimension STAP for TB‐based MIMO radar is established. Then, using the maximum SCNR as the design metric, the joint design model of the TB matrix and the reduced‐dimension STAP filter is presented. Furthermore, the cyclic optimisation method is exploited to deal with the non‐convex joint design problem with the energy constraint. Finally, simulation experiments demonstrate the joint design method of the TB matrix and the STAP filter not only has better output SCNR performance but also owns lower computational burden when compared with the other existing methods.
- 26 April 2021
- Published by Institution of Engineering and Technology (IET) in IET Radar, Sonar & Navigation
- Vol. 15 (6) , 655-665
Open AccessJoint design of transmit beamspace and reduced‐dimension receiver filter for MIMO radar STAP
In this article, the problem of the transmit beamspace (TB) matrix design in multiple‐input multiple‐output (MIMO) radar is considered. To reduce the computational burden and to focus the energy within optimal spatial sector, a joint design method of the TB matrix and a reduced‐dimension space‐time adaptive processing (STAP) filter is proposed based on the maximum signal‐to‐clutter‐plus‐noise ratio (SCNR). Firstly, the signal model of the reduced‐dimension STAP for TB‐based MIMO radar is established. Then, using the maximum SCNR as the design metric, the joint design model of the TB matrix and the reduced‐dimension STAP filter is presented. Furthermore, the cyclic optimisation method is exploited to deal with the non‐convex joint design problem with the energy constraint. Finally, simulation experiments demonstrate the joint design method of the TB matrix and the STAP filter not only has better output SCNR performance but also owns lower computational burden when compared with the other existing methods.