Isaac Tlhabadira
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Isaac Tlhabadira has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
I.A. Daniyan
Department of Industrial Engineering, Tshwane University of Technology, Pretoria 0001, South Africa
5 shared publicationsL. Masu
Department of Mechanical Engineering, Vaal University of Technology, Vanderbijlpark, South Africa
5 shared publicationsK. Mpofu
Tshwane Univ Technol, Dept Ind Engn, Pretoria, South Africa
3 shared publicationsL.R. VanStaden
3 shared publications- Ilesanmi Daniyan
Bells University of Technology
2 shared publications - Oluyemi Ojo Daramola
Department of Metallurgical and Materials Engineering, Federal University of Technology, Akure, Nigeria
2 shared publications
Latest Publications
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2933 (1)
Investigation of the manufacturability and cost analysis of automotive brake disc and pad
The processing of metal in most industries is an important process in order to obtain products that will meet the service requirements. The aim of this study is to evaluate the manufacturability and cost analysis of the brake disc and pad of an automobile. The following materials were considered for the brake disc gray cast iron, stainless steel, aluminum 7075 and Al-MMC). The various materials considered for the brake pads are carbon fibre, E-glass fibre, Kelvar 29, asbestos fibre and ceramic fibre. For the brake disc, the manufacturing cost in a foundry was separated into the following elements: material cost, labour cost, direct and overhead expenses. A comparative analysis was carried out among the different manufacturing technologies for the manufacturing of the brake disc to determine the cost effectiveness of the manufacturing process. The technologies evaluated include foundry, CNS using powermill CAM simulation, CNC turning using Sinumerik CAM simulation as well as the hot moulding technology. The results obtained in this study indicated that the total machining time was highest in stainless steel, followed by cast iron and Al 7075 with the least machinig cost observed in Al-MMC. Furthermore, the stainless steel and gray cast iron have 36% of the casting manufacturing costs while aluminium 7075 and Al-MMC have 14%. In addition, the total machining cost was highest in stainless steel, followed by cast iron and Al 7075 with the least machinig cost observed in Al-MMC. Finally, the material cost was highest in carbon fibre followed by Kelvar 29. Next to this is asbestos and ceramic with the least material cost observed in E glass fibre. The findings of this study will aid the decision making process on the most feasible materials for the development of brake pad and disc in terms of the manufacturing time and costs.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2933 (1)
Open AccessInvestigation of the manufacturability and cost analysis of automotive brake disc and pad
The processing of metal in most industries is an important process in order to obtain products that will meet the service requirements. The aim of this study is to evaluate the manufacturability and cost analysis of the brake disc and pad of an automobile. The following materials were considered for the brake disc gray cast iron, stainless steel, aluminum 7075 and Al-MMC). The various materials considered for the brake pads are carbon fibre, E-glass fibre, Kelvar 29, asbestos fibre and ceramic fibre. For the brake disc, the manufacturing cost in a foundry was separated into the following elements: material cost, labour cost, direct and overhead expenses. A comparative analysis was carried out among the different manufacturing technologies for the manufacturing of the brake disc to determine the cost effectiveness of the manufacturing process. The technologies evaluated include foundry, CNS using powermill CAM simulation, CNC turning using Sinumerik CAM simulation as well as the hot moulding technology. The results obtained in this study indicated that the total machining time was highest in stainless steel, followed by cast iron and Al 7075 with the least machinig cost observed in Al-MMC. Furthermore, the stainless steel and gray cast iron have 36% of the casting manufacturing costs while aluminium 7075 and Al-MMC have 14%. In addition, the total machining cost was highest in stainless steel, followed by cast iron and Al 7075 with the least machinig cost observed in Al-MMC. Finally, the material cost was highest in carbon fibre followed by Kelvar 29. Next to this is asbestos and ceramic with the least material cost observed in E glass fibre. The findings of this study will aid the decision making process on the most feasible materials for the development of brake pad and disc in terms of the manufacturing time and costs.
- 1 January 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 38, 590-594
Development and microstructural analysis of beta-SiAlONs produced by spark plasma sintering
- 1 January 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 38, 590-594
Development and microstructural analysis of beta-SiAlONs produced by spark plasma sintering
- 13 November 2019
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2019 (04) , 3347-3352
ANALYSIS OF SURFACE POST-PROCESSING TECHNIQUES FOR IMPROVEMENT OF ADDITIVE MANUFACTURED PARTS IN AEROSPACE
Additive manufacturing (AM) is a fast growing innovative technology with attractiveness to transform the manufacturing segment of the aerospace industries due to its ability to produce final usable parts. However, the surface finish of AM produced parts usually fall short of desires when compared...
- 13 November 2019
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2019 (04) , 3347-3352
ANALYSIS OF SURFACE POST-PROCESSING TECHNIQUES FOR IMPROVEMENT OF ADDITIVE MANUFACTURED PARTS IN AEROSPACE
Additive manufacturing (AM) is a fast growing innovative technology with attractiveness to transform the manufacturing segment of the aerospace industries due to its ability to produce final usable parts. However, the surface finish of AM produced parts usually fall short of desires when compared...
- 13 November 2019
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2019 (04) , 3353-3363
MODELLING AND OPTIMIZATION OF THE CUTTING FORCES DURING TI6AL4V MILLING PROCESS USING THE RESPONSE SURFACE METHODOLOGY AND DYNAMOMETER
The measurement of cutting forces using highly sensitive piezoelectric force sensors is significant in the optimization of the machining process. In this study, the modelling and optimization of the cutting forces during the milling process of Ti6Al4V was carried out using the Response Surface Me...
- 13 November 2019
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2019 (04) , 3353-3363
MODELLING AND OPTIMIZATION OF THE CUTTING FORCES DURING TI6AL4V MILLING PROCESS USING THE RESPONSE SURFACE METHODOLOGY AND DYNAMOMETER
The measurement of cutting forces using highly sensitive piezoelectric force sensors is significant in the optimization of the machining process. In this study, the modelling and optimization of the cutting forces during the milling process of Ti6Al4V was carried out using the Response Surface Me...
- 23 February 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 102 (9-12) , 3707-3718
Modelling and optimization of surface roughness during AISI P20 milling process using Taguchi method
- 23 February 2019
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 102 (9-12) , 3707-3718
Modelling and optimization of surface roughness during AISI P20 milling process using Taguchi method
- Open Access
- 1 January 2019
- Published by Elsevier in Procedia CIRP
- Vol. 84, 854-860
Process Design for Optimal Minimization of Resultant Cutting Force during the Machining of Ti-6Al-4V: Response Surface Method and Desirability Function Analysis
- 1 January 2019
- Published by Elsevier in Procedia CIRP
- Vol. 84, 854-860
Open AccessProcess Design for Optimal Minimization of Resultant Cutting Force during the Machining of Ti-6Al-4V: Response Surface Method and Desirability Function Analysis
- Open Access
- 1 January 2019
- Published by Elsevier in Procedia CIRP
- Vol. 84, 868-873
Process Design and Optimization of Surface Roughness during M200 TS Milling Process using the Taguchi Method
- 1 January 2019
- Published by Elsevier in Procedia CIRP
- Vol. 84, 868-873
Open AccessProcess Design and Optimization of Surface Roughness during M200 TS Milling Process using the Taguchi Method
- Open Access
- 1 January 2019
- Published by Elsevier in Procedia CIRP
- Vol. 84, 954-959
Model Design and Optimization of Carbide Milling Cutter for Milling Operation of M200 Tool Steel
- 1 January 2019
- Published by Elsevier in Procedia CIRP
- Vol. 84, 954-959
Open AccessModel Design and Optimization of Carbide Milling Cutter for Milling Operation of M200 Tool Steel
- Open Access
- 1 January 2019
- Published by Elsevier in Procedia CIRP
- Vol. 84, 861-867
Design and Optimization of Machining Parameters for Effective AISI P20 Removal Rate during Milling Operation
- 1 January 2019
- Published by Elsevier in Procedia CIRP
- Vol. 84, 861-867
Open AccessDesign and Optimization of Machining Parameters for Effective AISI P20 Removal Rate during Milling Operation