Amine Moubarik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Amine Moubarik has a total of 68 co-authors. Here are the top co-authors by number of shared publications:
Nabil Grimi
19 shared publicationsAbdelghani Boussetta
Higher School of Education and Training, Sultan Moulay Slimane University, Beni-Mellal, Morocco
12 shared publications- Mehdi Mennani
Mohammed VI Polytechnic University
11 shared publications - Anass Ait Benhamou
Department of Wood and Forest Sciences, Renewable Materials Research Centre (CRMR), Laval University, Quebec, QC G1V 0A6, Canada; College of Chemical Sciences and Engineering (CCSE), Institute of Sciences Technology and Innovation (IST&I), Mohammed VI Polytechnic University (UM6P), Benguerir 43150, Morocco
10 shared publications - Meriem Kasbaji
Materials Science, Energy and Nanoengineering (MSN) Department, Mohammed VI Polytechnic University, Lot 660 – Hay Moulay Rachid, 43150, Ben Guerir, Morocco
10 shared publications - Abdelghani Boussetta
Laboratory of Chemical Processes and Applied Materials, Polydisciplinary Faculty, Sultan Moulay Slimane University, Beni-Mellal, Morocco
7 shared publications
Latest Publications
- Open Access
- 11 February 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 16 (10) , 9092-9107
Lignin phosphorylation to enhance mechanical and physical properties and reduce formaldehyde emissions in plywood panels
Lignin is gaining more attention for its potential use in adhesives for wood-based composites owing to its accessibility, molecular structure, barrier properties, and potential for chemical modification. In order to assess the physical, thermal, and mechanical performances of alkaline lignin (AL) and its ability to reduce formaldehyde emissions in synthetic phenol formaldehyde (PF) adhesives used to glue plywood panels, AL was surface-modified by a phosphorylation treatment to produce phosphorylated alkali lignin. In this study, lignin was isolated from alkali-treated powdered argan shells and subsequently phosphorylated to obtain phosphorylated lignin (P-AL). The isolated lignin was characterized by two-dimensional (2D-1H and 13C NMR) heteronuclear single quantum coherence (HSQC) spectra to confirm its successful isolation from argan shells. Both AL and P-AL were then subjected to a series of analytical techniques, including Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) with elemental mapping, X-ray fluorescence (XRF) spectrometry, phosphorus nuclear magnetic resonance (31P NMR) spectroscopy, conductimetric titration (to determine the phosphorylation rate), thermogravimetric and derivative thermogravimetric analysis (TGA/DTG) and X-ray diffraction (XRD) analysis. Afterwards, P-AL was formulated with PF resin and applied to plywood panels, following characterizations to evaluate mechanical properties, such as bond strength (BS), modulus of rupture (MOR), modulus of elasticity (MOE), shear strength (SS), and formaldehyde emission (FE). Results showed that lignin phosphorylation had a significantly positive effect on plywood adhesion, especially in terms of FE, which decreased from 2.5 to 1.89 mg−1 m−2 h−1, while maintaining higher mechanical properties, including an MOE of 4144 MPa and an MOR of 66 MPa.
- 11 February 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 16 (10) , 9092-9107
Open AccessLignin phosphorylation to enhance mechanical and physical properties and reduce formaldehyde emissions in plywood panels
Lignin is gaining more attention for its potential use in adhesives for wood-based composites owing to its accessibility, molecular structure, barrier properties, and potential for chemical modification. In order to assess the physical, thermal, and mechanical performances of alkaline lignin (AL) and its ability to reduce formaldehyde emissions in synthetic phenol formaldehyde (PF) adhesives used to glue plywood panels, AL was surface-modified by a phosphorylation treatment to produce phosphorylated alkali lignin. In this study, lignin was isolated from alkali-treated powdered argan shells and subsequently phosphorylated to obtain phosphorylated lignin (P-AL). The isolated lignin was characterized by two-dimensional (2D-1H and 13C NMR) heteronuclear single quantum coherence (HSQC) spectra to confirm its successful isolation from argan shells. Both AL and P-AL were then subjected to a series of analytical techniques, including Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) with elemental mapping, X-ray fluorescence (XRF) spectrometry, phosphorus nuclear magnetic resonance (31P NMR) spectroscopy, conductimetric titration (to determine the phosphorylation rate), thermogravimetric and derivative thermogravimetric analysis (TGA/DTG) and X-ray diffraction (XRD) analysis. Afterwards, P-AL was formulated with PF resin and applied to plywood panels, following characterizations to evaluate mechanical properties, such as bond strength (BS), modulus of rupture (MOR), modulus of elasticity (MOE), shear strength (SS), and formaldehyde emission (FE). Results showed that lignin phosphorylation had a significantly positive effect on plywood adhesion, especially in terms of FE, which decreased from 2.5 to 1.89 mg−1 m−2 h−1, while maintaining higher mechanical properties, including an MOE of 4144 MPa and an MOR of 66 MPa.
- Open Access
- 11 February 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 16 (10) , 8641-8657
Performance enhancement of wood composites using cellulose-reinforced cornstarch–tannin adhesives derived from electrical-assisted extraction
This study investigates the impact of electrical-assisted extraction techniques on cellulose derived from almond shells and its performance in formaldehyde-free cornstarch–mimosa tannin (CM) adhesives. Cellulose was extracted using three methods: conventional alkali treatment (AT), alkali treatment assisted by pulsed electric fields (PEF), and alkali treatment assisted by high-voltage electrical discharges (HVED). Comprehensive analyses, including FTIR, XRD, TGA/DTG, DSC, and SEM, were conducted to evaluate the chemical structure, crystallinity, thermal stability, and morphology of the extracted celluloses. The results revealed that while cellulose yield varied slightly among treatments, electrical-assisted extraction significantly enhanced delignification and fibrillation without altering the cellulose I crystalline structure. Both PEF- and HVED-treated celluloses exhibited improved crystallinity (≈59%) and thermal stability (Tonset ≈ 303 °C), indicating superior structural integrity. Incorporation of these celluloses into CM adhesives increased viscosity, solid content, and shear strength, with optimal performance at 6 wt% cellulose loading. Particleboards bonded with HAC-CM adhesives showed the highest mechanical properties (IB = 0.79 MPa, MOR = 32.27 MPa, MOE = 3125 MPa), exceeding EN 312 (P4) standard requirements. Water absorption and thickness swelling were markedly reduced, confirming enhanced moisture resistance. Overall, HVED-assisted extraction produced cellulose with superior reinforcing capability, demonstrating a sustainable and high-performance pathway for developing formaldehyde-free wood adhesives from agricultural residues.
- 11 February 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 16 (10) , 8641-8657
Open AccessPerformance enhancement of wood composites using cellulose-reinforced cornstarch–tannin adhesives derived from electrical-assisted extraction
This study investigates the impact of electrical-assisted extraction techniques on cellulose derived from almond shells and its performance in formaldehyde-free cornstarch–mimosa tannin (CM) adhesives. Cellulose was extracted using three methods: conventional alkali treatment (AT), alkali treatment assisted by pulsed electric fields (PEF), and alkali treatment assisted by high-voltage electrical discharges (HVED). Comprehensive analyses, including FTIR, XRD, TGA/DTG, DSC, and SEM, were conducted to evaluate the chemical structure, crystallinity, thermal stability, and morphology of the extracted celluloses. The results revealed that while cellulose yield varied slightly among treatments, electrical-assisted extraction significantly enhanced delignification and fibrillation without altering the cellulose I crystalline structure. Both PEF- and HVED-treated celluloses exhibited improved crystallinity (≈59%) and thermal stability (Tonset ≈ 303 °C), indicating superior structural integrity. Incorporation of these celluloses into CM adhesives increased viscosity, solid content, and shear strength, with optimal performance at 6 wt% cellulose loading. Particleboards bonded with HAC-CM adhesives showed the highest mechanical properties (IB = 0.79 MPa, MOR = 32.27 MPa, MOE = 3125 MPa), exceeding EN 312 (P4) standard requirements. Water absorption and thickness swelling were markedly reduced, confirming enhanced moisture resistance. Overall, HVED-assisted extraction produced cellulose with superior reinforcing capability, demonstrating a sustainable and high-performance pathway for developing formaldehyde-free wood adhesives from agricultural residues.
- 16 December 2025
- Published by Elsevier in International Journal of Biological Macromolecules
- Vol. 338 (Pt 1) , 149691
Phosphorylated lignin: Recent advances in synthesis through chemical functionalization, structural properties, and emerging applications: A review
- 16 December 2025
- Published by Elsevier in International Journal of Biological Macromolecules
- Vol. 338 (Pt 1) , 149691
Phosphorylated lignin: Recent advances in synthesis through chemical functionalization, structural properties, and emerging applications: A review
- 8 May 2025
- Published by Elsevier in International Journal of Biological Macromolecules
- Vol. 311 (Pt 3) , 144025
Enhancing adhesive properties with unmodified and phosphate-modified chitin in particleboard production
- 8 May 2025
- Published by Elsevier in International Journal of Biological Macromolecules
- Vol. 311 (Pt 3) , 144025
Enhancing adhesive properties with unmodified and phosphate-modified chitin in particleboard production
- 20 November 2024
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 17 (1) , 113-141
What is the potential of walnut shell-derived carbon in battery applications?
The use of walnut shells for energy storage offers a sustainable, innovative approach, enhancing energy density and cost efficiency. While it presents environmental benefits, challenges remain in scalability and optimization.
- 20 November 2024
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 17 (1) , 113-141
What is the potential of walnut shell-derived carbon in battery applications?
The use of walnut shells for energy storage offers a sustainable, innovative approach, enhancing energy density and cost efficiency. While it presents environmental benefits, challenges remain in scalability and optimization.
- 4 October 2024
- Published by Springer Nature
- p. 3-56
Introduction to Carbon Nanostructures: History, Classifications, and Recent Advances
- 4 October 2024
- Published by Springer Nature
- p. 3-56
Introduction to Carbon Nanostructures: History, Classifications, and Recent Advances
- 3 October 2024
- Published by Springer Nature
- p. 101-126
Experimental Techniques for Evaluating Photocatalytic Activity of Graphene
- 3 October 2024
- Published by Springer Nature
- p. 101-126
Experimental Techniques for Evaluating Photocatalytic Activity of Graphene
- 28 September 2024
- Published by Springer Nature
- p. 49-70
Photocatalytic Materials, Design Concepts, and Functional Mechanistic Pathways
- 28 September 2024
- Published by Springer Nature
- p. 49-70
Photocatalytic Materials, Design Concepts, and Functional Mechanistic Pathways