JCJames C. Culbertson

James C. Culbertson

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


James C. Culbertson has a total of 86 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Wafer scale characterization of bulk AlN substrates and homoepitaxial growth

    by A. G. Jacobs, K. R. Gann, E. G. Rocco, D. J. Pennachio, K. Hogan, J. R. Grandusky, N. A. Mahadik, J. C. Culbertson, J. A. Freitas, J. M. Woodward, et al.

    Aluminum nitride (AlN) is well suited to address evolving needs of future power systems for increased density, efficiency, and voltage handling. Eventual commercialization of power devices requires maturation of substrate technology to ensure fabrication of consistent devices impacted by the spatial distribution of defects and substrate inhomogeneities. Commercial 50 mm AlN substrates grown by physical vapor transport were characterized as received and after 1 μm of homoepitaxial growth by metalorganic chemical vapor deposition. Optical profilometry determined macro-roughness to be sub-nm while atomic force microscopy reveals consistent step edges and 0.1 nm micro-roughness, despite observation of sporadic 100–400 nm wide, ∼1 nm deep depressions. Sub-bandgap photoluminescence reveals broad spectroscopic signals, which slowly vary spatially across the wafer, corresponding with faint visible coloration. Raman spectroscopy indicates uniform, high crystal quality but shows increased background scattering associated with micrometer-scale features visible in optical microscopy. High-resolution x-ray diffraction validates the crystal quality with median (0002) full-width at half maximum of 17.6 arc sec and x-ray topography identified varying regions with dislocation density from ∼102 cm−2 to ∼mid-105 cm−2. Electron microscopy revealed nano-pipes that may be the origin of the nanoscale depressions and that at least some bright optical features are aluminum platelets with coherent atomic boundaries. After epitaxial growth, surface morphology retained smooth macro- and micro-roughness with clear step edges, demonstrating viability of device-relevant epitaxial layer thicknesses for power devices. Three wafers from one boule were characterized, indicating consistent wafer-to-wafer characteristics, critical for future device commercialization.


  • Open Access

    Characterization of extended defect evolution in 1.2–12 μm thick homoepitaxial (010) β-Ga2O3 grown by close-injection showerhead metal-organic chemical vapor deposition

    by Marko J. Tadjer, Kenny Hyunh, James C. Culbertson, Evan R. Glaser, Michael E. Liao, John Gaskins, Hannah N. Masten, Alan G. Jacobs, Nadeem A. Mahadik, James Spencer Lundh, et al.

    Homoepitaxial Si-doped (010) β-Ga2O3 epitaxial layers with thicknesses ranging from 1.2 to 12 μm were grown simultaneously via close-injection showerhead metal-organic chemical vapor deposition on both Czochralski and edge-defined, film-fed grown (010) β-Ga2O3:Fe substrates. Structural characterization was performed via x-ray diffraction [full-width at half maxima of 21–72 arcsec depending on epilayer thickness and substrate, measured from the symmetric (020) reflection], x-ray topography, Raman spectroscopy, cathodoluminescence spectroscopy, and transmission electron microscopy. Surface characterization was performed via atomic force microscope (AFM) and Nomarski imaging, and electrical characterization was performed via electron paramagnetic resonance spectroscopy and Hall effect measurements. In addition, thermal conductivity was measured via steady-state thermoreflectance. AFM imaging revealed a number of extended defects forming in the epilayer, and transmission electron microscopy imaging detailed a V-shaped pit defect formed by misoriented twin defects likely originating from a defect at or near the substrate surface. The Hall effect data (NS = 2.81–3.1 × 1017 cm−3 and μH = 81.5–103.5 cm2/V s), surface roughness (1.78–4.25 nm rms), and thermal conductivity measurements (19.3–19.8 W/m K) yielded comparable results among all samples, independent of epilayer thickness. These results suggested that even thicker, high quality epitaxial (010) β-Ga2O3 could be grown via this technique, provided that the development of the observed extended defects can be mitigated.


  • High-yield growth of high-quality cubic BAs single crystals using the Bridgman method

    by Wenhao Liu, Pawan Koirala, Evan R. Glaser, Hanlin Wu, Aswin Kondusamy, Nikhil Dhale, Mahammed S. Patel, Sam White, James C. Culbertson, Jaime A. Freitas, et al.

    The increasing complexity of semiconductor devices fabricated from wide-bandgap and ultra-wide-bandgap materials demand advanced thermal management solutions to mitigate heat buildup, a major cause of device failure. High thermal conductivity materials are thus becoming crucial for thermal management. Cubic boron arsenide (c-BAs) has emerged as a promising candidate. However, challenges remain in synthesizing high-quality crystals with low defect concentrations, high homogeneous thermal conductivity, and high yields using the conventional chemical vapor transport method. In this study, we report the synthesis of high-yield c-BAs single crystals using the Bridgman method. The crystals exhibit high uniformity, reduced defect densities, and lower carrier concentrations as confirmed through x-ray diffraction, Raman spectroscopy, temperature-dependent photoluminescence, and electrical transport measurements. Our work represents a significant step toward scalable production of high-quality c-BAs for industrial applications, offering a practical solution for improving thermal management in next-generation electronic devices.


  • Open Access

    Structural and optical properties of cubic GaN films on high-thermal conductivity substrates

    by Jaime A. Freitas, James C. Culbertson, David F. Storm, Nadeemullah A. Mahadik, Neeraj Nepal, Travis J. Anderson

    A thin cubic-GaN epitaxial layer was grown by plasma-assisted molecular-beam epitaxy directly on a (100) cubic-boron-nitride nucleation layer that was previously deposited on a (100)-oriented, type IIA, single-crystal chemical-vapor deposition diamond substrate. X-ray diffraction measurements verified that (100)-plane zincblende is the dominant crystal structure of the GaN layer, with a small contribution from the wurtzite phase in some sample regions. Detailed atomic force microscopy and Raman scattering measurements confirmed the XRD findings. Low temperature photoluminescence spectra show a dominant emission line near 3.12 eV and a weaker emission line near 3.21 eV. The former is assigned to a recombination process involving electrons bound to shallow donors with holes bound to shallow acceptors (donor–acceptor pair recombination process). The latter, which becomes dominant at temperatures above 50 K, is assigned to a recombination process involving the annihilation of excitons bound to shallow impurities. Room temperature transmission measurements yielded a direct bandgap of 3.23 eV, which is close to the reported values for c-GaN. These results confirm that cubic-GaN was successfully deposited on a high thermal-conductivity diamond substrate. This opens the door to exploring the potential of cubic-GaN devices for high-power applications, given that large area diamond substrates are becoming available.


  • Open Access

    Hydrogenated silicene grown by plasma enhanced chemical-vapor deposition

    by Battogtokh Jugdersuren, Xiao Liu, James C. Culbertson, Nadeemullah Mahadik, Owain Thomas, Yi Shu

    Silicene, a 2D hexagonal structure of silicon, has shown great promise for next-generation advanced electronic devices due to recent progress. However, one major obstacle to its application and integration into devices is its strong tendency of rapid oxidation in an ambient environment. Enhancing the chemical inertness by means of chemical modification without comprising its unique structure and properties is vital. Here, we report the fabrication of hydrogenated silicene grown on polycrystalline Ag films by means of plasma-enhanced chemical-vapor deposition (PECVD) with proper hydrogen dilution. Our Raman spectroscopy and x-ray diffraction results show the existence of typical monolayer and few-layer silicene. The x-ray photoelectron spectroscopy demonstrates its oxidation resistance after a few minutes of air exposure in a class 100 clean room. We propose that PECVD silicene can be an alternative to molecular-beam-epitaxy silicene for potential low-cost and large-area silicene applications.


  • Thermoelectric properties of nanocrystalline silicon film grown by PECVD

    by Battogtokh Jugdersuren, Xiao Liu, James C. Culbertson, Christopher N. Chervin, Bethany M. Hudak, Rhonda M. Stroud


  • Open Access

    Characterization of Defects in GaN: Optical and Magnetic Resonance Techniques

    by Jaime A. Freitas, James C. Culbertson, Evan R. Glaser

    GaN and its alloys with InN and AlN are of technological importance for a variety of optical, electronic, and optoelectronic devices due to its high thermal conductivity, wide band gap, high breakdown voltage and high saturation velocity. GaN-based devices now provide superior performance for a variety of high power, high frequency, high temperature, and optical applications. The major roadblock for the full realization of Nitride semiconductor potential is still the availability of affordable large-area and high-quality native substrates with controlled electrical properties. Despite the impressive accomplishments recently achieved by techniques such as hydride vapor phase epitaxy and ammonothermal for GaN growth, much more must be attained before establishing a fully satisfactory bulk growth method for this material. Recent results suggest that ammonothermal GaN wafers can be successfully used as seeds to grow thick freestanding GaN wafers by hydride vapor phase epitaxy. A brief review of defect-sensitive optical and paramagnetic spectroscopy techniques employed to evaluate structural, optical, and electronic properties of the state-of-the-art bulk and thick-film (quasi-bulk) Nitride substrates and homoepitaxial films is presented. Defects control the performance of devices and feeding back knowledge of defects to growth efforts is key to advancing technology.


  • Influence of oxygen partial pressure on properties of monoclinic Ga2O3 deposited on sapphire substrates

    by Jaime A. FreitasJr., James C. Culbertson, Neeraj Nepal, Alyssa L. Mock, Marko J. Tadjer, Zixuan Feng, Hongping Zhao

    Thin monoclinic Ga2O3 films were deposited on c-plane sapphire substrates by low pressure chemical vapor deposition. The thin films were synthesized using high purity metallic gallium (Ga) and oxygen gas (O2) as precursors. The effect of oxygen volume percentage on the growth rate of thin films was observed at two growth temperatures. Within the investigated growth window, a maximum growth rate of ∼2.9 μm/h was obtained for an oxygen volume percentage of 4.8% with a growth temperature at 800 °C. The film growth rate decreased as growth temperature increased when other growth parameters were kept the same. X-ray diffraction indicates that all films have the β-Ga2O3 structure with (−201) orientation, and those deposited with higher oxygen partial pressure are thicker and have improved crystalline quality. Polarized micro-Raman scattering is consistent with small grains of (−201) β-Ga2O3 having random in-plane orientations. The large variation of the relative intensities of overlapping emission bands contributing to the broad luminescence emission extending between 1.5 and 4.5 eV (∼825 and 275 nm) suggest that deposition conditions strongly affect different defect concentrations. Films deposited at 800 °C with a higher oxygen partial pressure yielded higher resistance, which may result from the incorporation of gallium vacancies, identified as a compensating point defect affecting the electrical conductivity of bulk monoclinic Ga2O3.


  • (Invited) GaN Wafers with Dramatically Improved Crystalline and Electrical Properties

    by Jaime A. Freitas, James C Culbertson, Nadeemullah A Mahadik, Marko J. Tadjer, Tomasz Sochacki, Michal Bockowski

    Gallium Nitride (GaN) and its alloys with Indium and Aluminum, part of third semiconductors generation, are revolutionizing both the optoelectronic and electronic device industries. Despite a previous lack of native substrates, a number of devices exceeding the performance of those fabricated from well-developed semiconductors were realized. However, the fabrication of higher performance devices with higher yields requires higher crystalline quality substrates with fully controlled electronic transport properties. Bulk ammonothermal GaN substrates, recently developed and commercialized, are characterized by low dislocation density, a single crystal nature, and high flatness; but they lack full control of the electrical properties. It is expected that films deposited by vapor transport techniques, typically with low impurities background, would allow the growth of materials with high crystalline quality and improved electrical properties. More recently, it was demonstrated that thick GaN films deposited by Hydride Vapor Phase Epitaxy (HVPE, a fast deposition process) on ammonothermal GaN substrates reproduce the high crystalline quality of those substrates, and have free carrier concentrations that are several orders of magnitude lower that of the substrates [1]. We have verified that such HVPE GaN wafers can be used for further homoepitaxial growth. This is extremely important, because it demonstrates the usefulness of this new type of substrate to fabricate highly efficient optoelectronic and electronic devices. An ~800 mm thick HVPE film deposited on an (0001) epi-ready Ammono substrate (~0.3 degree toward “m”) was removed from the reactor and its surface was chemical-mechanically polished (CMP). This template was put back in the HVPE reactor and an additional ~800 mm was deposited. The final crystal consisted of two sequentially grown HVPE-GaN layers on the Ammono substrate. The top HVPE layer was sliced off and three samples were diced from different regions of this wafer. The surfaces of these samples were mechanically polished and CMP finished. A combination of techniques was employed to investigate the structural, optical, and electrical properties of the crystals. High resolution XRD was measured on two samples using a Rigaku Smartlab diffractometer with a four bounce Ge (220) monochromator. Lattice parameters were measured using symmetric and asymmetric scans: sample A: c=5.1856Å and a=3.1824Å; sample B were, c=5.1856Å and a=3.1839Å. These values are very close to the bulk lattice constants. The rocking curves for these samples were measured and had full widths at half maximum of ~16 arcsecs, indicating superior crystalline quality. High lateral and depth resolution micro-Raman scattering (RS) measurements were carried out on the front and back surfaces of two samples. The E2 2 phonon frequency was mapped on both faces of two samples; the distribution of Raman shifts was 567.45±0.05 cm-1, indicating stress free GaN. The A1(LO) phonon frequencies and the linewidths measured on the Ga-polar face were larger than those measured on the N-polar face; this is consistent with a larger incorporation of donor impurities as the growth proceeds. Low temperature, high spectral resolution photoluminescence (PL) measurements carried out on the Ga- and N-polar faces of these samples were also consistent with more doping as the growth proceeds [2]. SIMS depth profile measurements also confirm this observation. Hall measurements provided information about the free-carrier concentration and carrier mobility. [1] T. Sochacki, et al., J.J. Appl. Phys., 53 (2014)05FA04. [2] J.A. Freitas, Jr., et al., Cryst. Growth & Design, 15 (2015) 4837.

  • Growth of High Crystalline Quality HVPE-GaN Crystals with Controlled Electrical Properties

    by Jr. J. A. Freitas, J. C. Culbertson, N. A. Mahadik, T. Sochacki, M. Bockowski, M. Iwinska