Nadeemullah A. Mahadik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nadeemullah A. Mahadik has a total of 143 co-authors. Here are the top co-authors by number of shared publications:
- Robert E. Stahlbush
U. S. Naval Research Laboratory
6 shared publications - James C. Culbertson
U.S. Naval Research Laboratory 1 , Washington, District of Columbia 20375
5 shared publications - James C. Gallagher
U.S. Naval Research Laboratory
5 shared publications - Karl D. Hobart
U.S. Naval Research Laboratory
5 shared publications - Jaime A. FreitasJr.
U.S. Naval Research Laboratory 1 , Washington, District of Columbia 20375
4 shared publications - Marko J. Tadjer
U.S. Naval Research Laboratory 2 , Washington, District of Columbia 20375
4 shared publications
Latest Publications
- Open Access
- 1 July 2026
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 41 (7) , 075016
U-Net deep learning model for rapid identification of defects in SiC
Rapid wafer-scale defect identification and quantification are essential to achieve high yielding and reliable materials for device fabrication. Since defects are microscopic and the measurement scales are macroscopic, a quick, non-destructive automated process is needed to assess wafer quality. Although methods for wafer-scale defect visualization are well established, the appearance of defects can vary in size, shape, intensity, and signal to noise across a single sample. Using a traditional pattern matching technique would require extensive optimization, and if blind spots in the method were observed, corrections may be labor intensive to implement. This paper discusses using machine learning models to detect and classify defects in SiC and demonstrates that an implementation of the U-Net architecture is effective at identifying four types of critical defects in SiC with ultraviolet photoluminescence: stacking faults, polytype inclusions, threading screw/mixed dislocations, and basal plane dislocations. The resulting model can evaluate both 6-inch and 8-inch SiC wafers in minutes.
- 1 July 2026
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 41 (7) , 075016
Open AccessU-Net deep learning model for rapid identification of defects in SiC
Rapid wafer-scale defect identification and quantification are essential to achieve high yielding and reliable materials for device fabrication. Since defects are microscopic and the measurement scales are macroscopic, a quick, non-destructive automated process is needed to assess wafer quality. Although methods for wafer-scale defect visualization are well established, the appearance of defects can vary in size, shape, intensity, and signal to noise across a single sample. Using a traditional pattern matching technique would require extensive optimization, and if blind spots in the method were observed, corrections may be labor intensive to implement. This paper discusses using machine learning models to detect and classify defects in SiC and demonstrates that an implementation of the U-Net architecture is effective at identifying four types of critical defects in SiC with ultraviolet photoluminescence: stacking faults, polytype inclusions, threading screw/mixed dislocations, and basal plane dislocations. The resulting model can evaluate both 6-inch and 8-inch SiC wafers in minutes.
- Open Access
- 25 June 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (24)
Propagation mechanism of non-step-flow direction BPDs into 4H-SiC epitaxial layers and their stacking fault expansion behavior
Basal plane dislocations (BPDs) are a primary reliability concern for SiC power electronics. Almost all BPDs propagating from the substrate to the epitaxial layer in 4H-SiC have line directions and Burgers vectors almost parallel to the step-flow growth direction. A novel and unexpected propagation mechanism of a BPD with the dislocation vectors 120° to the step-flow direction is reported. Direct imaging with multiple techniques, including after carrier injection, was performed to investigate the propagation mechanisms, microstructural analysis, and associated stacking fault (SF) expansion. It was found that the Burgers vector of this BPD was 13[2¯110] as opposed to the typical ±13[112¯0] and that its propagation was made possible through the interaction between the BPD and a threading mixed dislocation (TMD), which provided spiral growth steps in multiple directions. The interaction also causes the multiplication of SFs, which is described. Additionally, the TMD gets deflected on to the basal plane inside the epitaxial layer and forms a Frank + Shockley fault. The three physical mechanisms identified in SiC wafers increase a power device’s on-state resistance and reverse current leakage, thereby jeopardizing the device’s reliability.
- 25 June 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (24)
Open AccessPropagation mechanism of non-step-flow direction BPDs into 4H-SiC epitaxial layers and their stacking fault expansion behavior
Basal plane dislocations (BPDs) are a primary reliability concern for SiC power electronics. Almost all BPDs propagating from the substrate to the epitaxial layer in 4H-SiC have line directions and Burgers vectors almost parallel to the step-flow growth direction. A novel and unexpected propagation mechanism of a BPD with the dislocation vectors 120° to the step-flow direction is reported. Direct imaging with multiple techniques, including after carrier injection, was performed to investigate the propagation mechanisms, microstructural analysis, and associated stacking fault (SF) expansion. It was found that the Burgers vector of this BPD was 13[2¯110] as opposed to the typical ±13[112¯0] and that its propagation was made possible through the interaction between the BPD and a threading mixed dislocation (TMD), which provided spiral growth steps in multiple directions. The interaction also causes the multiplication of SFs, which is described. Additionally, the TMD gets deflected on to the basal plane inside the epitaxial layer and forms a Frank + Shockley fault. The three physical mechanisms identified in SiC wafers increase a power device’s on-state resistance and reverse current leakage, thereby jeopardizing the device’s reliability.
- Open Access
- 18 May 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (20)
Wafer scale characterization of bulk AlN substrates and homoepitaxial growth
Aluminum nitride (AlN) is well suited to address evolving needs of future power systems for increased density, efficiency, and voltage handling. Eventual commercialization of power devices requires maturation of substrate technology to ensure fabrication of consistent devices impacted by the spatial distribution of defects and substrate inhomogeneities. Commercial 50 mm AlN substrates grown by physical vapor transport were characterized as received and after 1 μm of homoepitaxial growth by metalorganic chemical vapor deposition. Optical profilometry determined macro-roughness to be sub-nm while atomic force microscopy reveals consistent step edges and 0.1 nm micro-roughness, despite observation of sporadic 100–400 nm wide, ∼1 nm deep depressions. Sub-bandgap photoluminescence reveals broad spectroscopic signals, which slowly vary spatially across the wafer, corresponding with faint visible coloration. Raman spectroscopy indicates uniform, high crystal quality but shows increased background scattering associated with micrometer-scale features visible in optical microscopy. High-resolution x-ray diffraction validates the crystal quality with median (0002) full-width at half maximum of 17.6 arc sec and x-ray topography identified varying regions with dislocation density from ∼102 cm−2 to ∼mid-105 cm−2. Electron microscopy revealed nano-pipes that may be the origin of the nanoscale depressions and that at least some bright optical features are aluminum platelets with coherent atomic boundaries. After epitaxial growth, surface morphology retained smooth macro- and micro-roughness with clear step edges, demonstrating viability of device-relevant epitaxial layer thicknesses for power devices. Three wafers from one boule were characterized, indicating consistent wafer-to-wafer characteristics, critical for future device commercialization.
- 18 May 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (20)
Open AccessWafer scale characterization of bulk AlN substrates and homoepitaxial growth
Aluminum nitride (AlN) is well suited to address evolving needs of future power systems for increased density, efficiency, and voltage handling. Eventual commercialization of power devices requires maturation of substrate technology to ensure fabrication of consistent devices impacted by the spatial distribution of defects and substrate inhomogeneities. Commercial 50 mm AlN substrates grown by physical vapor transport were characterized as received and after 1 μm of homoepitaxial growth by metalorganic chemical vapor deposition. Optical profilometry determined macro-roughness to be sub-nm while atomic force microscopy reveals consistent step edges and 0.1 nm micro-roughness, despite observation of sporadic 100–400 nm wide, ∼1 nm deep depressions. Sub-bandgap photoluminescence reveals broad spectroscopic signals, which slowly vary spatially across the wafer, corresponding with faint visible coloration. Raman spectroscopy indicates uniform, high crystal quality but shows increased background scattering associated with micrometer-scale features visible in optical microscopy. High-resolution x-ray diffraction validates the crystal quality with median (0002) full-width at half maximum of 17.6 arc sec and x-ray topography identified varying regions with dislocation density from ∼102 cm−2 to ∼mid-105 cm−2. Electron microscopy revealed nano-pipes that may be the origin of the nanoscale depressions and that at least some bright optical features are aluminum platelets with coherent atomic boundaries. After epitaxial growth, surface morphology retained smooth macro- and micro-roughness with clear step edges, demonstrating viability of device-relevant epitaxial layer thicknesses for power devices. Three wafers from one boule were characterized, indicating consistent wafer-to-wafer characteristics, critical for future device commercialization.
- Open Access
- 18 May 2026
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 452, 79-85
Growth and Characterization of High-Quality Thick Epitaxial 4H-SiC Wafers for High Voltage Devices
Silicon carbide is a leading wide-bandgap semiconductor for high-voltage power electronics. For 6.5–10 kV operation, thick epitaxial layers (≥60 µm) are required to sustain depletion width and maintain uniform electric fields, placing a premium on low extended-defect densities in both substrate and epilayer. Thick epitaxial 4H-SiC layers of 60 µm and 110 µm were grown on 6-inch substrates in a multi-wafer warm-wall reactor and evaluated by synchrotron X-ray topography in grazing-incidence (22-4 16) and transmission (11-20) geometries. Transmission imaging showed substrate dislocation content near the lower bound typically reported for 6-inch wafers. Notably, grazing-incidence topography (penetration depth >40 µm) revealed no basal-plane dislocations propagating into the epilayers, consistent with efficient dislocation conversion at the substrate–epilayer interface. The 3C-SiC inclusion density was ~30 per 6-inch wafer for 60 µm epilayers and ~60 per wafer for 110 µm epilayers; the average micropipes density varies from 0 to 5 for both 60 and 110 um epiwafers. Threading dislocation densities—screw, edge, and mixed—were on the order of 1.0–2.0 × 10³ cm⁻². These results establish thick 4H-SiC epilayers with suppressed basal-plane propagation and substantially reduced extended-defect content, providing a strong basis for reliable 6.5–10 kV device fabrication.
- 18 May 2026
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 452, 79-85
Open AccessGrowth and Characterization of High-Quality Thick Epitaxial 4H-SiC Wafers for High Voltage Devices
Silicon carbide is a leading wide-bandgap semiconductor for high-voltage power electronics. For 6.5–10 kV operation, thick epitaxial layers (≥60 µm) are required to sustain depletion width and maintain uniform electric fields, placing a premium on low extended-defect densities in both substrate and epilayer. Thick epitaxial 4H-SiC layers of 60 µm and 110 µm were grown on 6-inch substrates in a multi-wafer warm-wall reactor and evaluated by synchrotron X-ray topography in grazing-incidence (22-4 16) and transmission (11-20) geometries. Transmission imaging showed substrate dislocation content near the lower bound typically reported for 6-inch wafers. Notably, grazing-incidence topography (penetration depth >40 µm) revealed no basal-plane dislocations propagating into the epilayers, consistent with efficient dislocation conversion at the substrate–epilayer interface. The 3C-SiC inclusion density was ~30 per 6-inch wafer for 60 µm epilayers and ~60 per wafer for 110 µm epilayers; the average micropipes density varies from 0 to 5 for both 60 and 110 um epiwafers. Threading dislocation densities—screw, edge, and mixed—were on the order of 1.0–2.0 × 10³ cm⁻². These results establish thick 4H-SiC epilayers with suppressed basal-plane propagation and substantially reduced extended-defect content, providing a strong basis for reliable 6.5–10 kV device fabrication.
- Open Access
- 5 September 2025
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 375, 35-41
Formation Mechanism and Complex Faulting Behavior of a BPD Loop in 180 μm Thick 4H-SiC Epitaxial Layer
4H-SiC with 180 μm epilayer was subjected to UV exposure. Stacking fault expanded from basal plane dislocation (BPD) loop generated during growth in the epilayer was observed by UV Photoluminescence Imaging (UVPL) and X-ray Topograph (XRT) techniques. Interactions between partial dislocation, emanating from the BPD loop and gliding via recombination-enhanced dislocation glide mechanism, and threading screw/mix dislocations are detected and analyzed, where stacking faults migrate to different basal plane after the interactions. Such migration increases the faulted volume that can severely degrade reliability and performance of high power SiC devices by increasing reverse leakage current and on-state resistance and could eventually lead to device failure.
- 5 September 2025
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 375, 35-41
Open AccessFormation Mechanism and Complex Faulting Behavior of a BPD Loop in 180 μm Thick 4H-SiC Epitaxial Layer
4H-SiC with 180 μm epilayer was subjected to UV exposure. Stacking fault expanded from basal plane dislocation (BPD) loop generated during growth in the epilayer was observed by UV Photoluminescence Imaging (UVPL) and X-ray Topograph (XRT) techniques. Interactions between partial dislocation, emanating from the BPD loop and gliding via recombination-enhanced dislocation glide mechanism, and threading screw/mix dislocations are detected and analyzed, where stacking faults migrate to different basal plane after the interactions. Such migration increases the faulted volume that can severely degrade reliability and performance of high power SiC devices by increasing reverse leakage current and on-state resistance and could eventually lead to device failure.
- Open Access
- 1 July 2025
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 40 (7) , 075003
Wafer scale assessment of dislocation defects on SiC wafers using a convolutional neural network
Wide bandgap semiconductors, such as SiC, are expected to surpass traditional silicon-based technologies in high-power electronics applications, owing to their potential for reduced size, weight, and enhanced power efficiency. SiC, in particular, has evolved significantly, reaching a maturity that enables its adoption in high-voltage applications including power modules. However, the current state-of-the-art SiC epitaxial wafers face significant challenges, primarily due to the presence of threading dislocations, basal plane dislocations, stacking faults, polytype inclusions, and screw dislocations. These structural imperfections lead to electron and hole carrier scattering, which impairs device performance. Addressing this, the present research introduces a novel approach employing a convolutional neural network (CNN) trained to identify and quantify dislocation defects with high precision. Analysis of the models shows it both highlights the features of interest and delineates the shape, size, and number of the dislocations with higher accuracy than the manual labeling used to train the model, suggesting that CNN has successfully captured the subtle details needed to identify dislocations defects.
- 1 July 2025
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 40 (7) , 075003
Open AccessWafer scale assessment of dislocation defects on SiC wafers using a convolutional neural network
Wide bandgap semiconductors, such as SiC, are expected to surpass traditional silicon-based technologies in high-power electronics applications, owing to their potential for reduced size, weight, and enhanced power efficiency. SiC, in particular, has evolved significantly, reaching a maturity that enables its adoption in high-voltage applications including power modules. However, the current state-of-the-art SiC epitaxial wafers face significant challenges, primarily due to the presence of threading dislocations, basal plane dislocations, stacking faults, polytype inclusions, and screw dislocations. These structural imperfections lead to electron and hole carrier scattering, which impairs device performance. Addressing this, the present research introduces a novel approach employing a convolutional neural network (CNN) trained to identify and quantify dislocation defects with high precision. Analysis of the models shows it both highlights the features of interest and delineates the shape, size, and number of the dislocations with higher accuracy than the manual labeling used to train the model, suggesting that CNN has successfully captured the subtle details needed to identify dislocations defects.
- Open Access
- 15 January 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (3)
Structural and optical properties of cubic GaN films on high-thermal conductivity substrates
A thin cubic-GaN epitaxial layer was grown by plasma-assisted molecular-beam epitaxy directly on a (100) cubic-boron-nitride nucleation layer that was previously deposited on a (100)-oriented, type IIA, single-crystal chemical-vapor deposition diamond substrate. X-ray diffraction measurements verified that (100)-plane zincblende is the dominant crystal structure of the GaN layer, with a small contribution from the wurtzite phase in some sample regions. Detailed atomic force microscopy and Raman scattering measurements confirmed the XRD findings. Low temperature photoluminescence spectra show a dominant emission line near 3.12 eV and a weaker emission line near 3.21 eV. The former is assigned to a recombination process involving electrons bound to shallow donors with holes bound to shallow acceptors (donor–acceptor pair recombination process). The latter, which becomes dominant at temperatures above 50 K, is assigned to a recombination process involving the annihilation of excitons bound to shallow impurities. Room temperature transmission measurements yielded a direct bandgap of 3.23 eV, which is close to the reported values for c-GaN. These results confirm that cubic-GaN was successfully deposited on a high thermal-conductivity diamond substrate. This opens the door to exploring the potential of cubic-GaN devices for high-power applications, given that large area diamond substrates are becoming available.
- 15 January 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (3)
Open AccessStructural and optical properties of cubic GaN films on high-thermal conductivity substrates
A thin cubic-GaN epitaxial layer was grown by plasma-assisted molecular-beam epitaxy directly on a (100) cubic-boron-nitride nucleation layer that was previously deposited on a (100)-oriented, type IIA, single-crystal chemical-vapor deposition diamond substrate. X-ray diffraction measurements verified that (100)-plane zincblende is the dominant crystal structure of the GaN layer, with a small contribution from the wurtzite phase in some sample regions. Detailed atomic force microscopy and Raman scattering measurements confirmed the XRD findings. Low temperature photoluminescence spectra show a dominant emission line near 3.12 eV and a weaker emission line near 3.21 eV. The former is assigned to a recombination process involving electrons bound to shallow donors with holes bound to shallow acceptors (donor–acceptor pair recombination process). The latter, which becomes dominant at temperatures above 50 K, is assigned to a recombination process involving the annihilation of excitons bound to shallow impurities. Room temperature transmission measurements yielded a direct bandgap of 3.23 eV, which is close to the reported values for c-GaN. These results confirm that cubic-GaN was successfully deposited on a high thermal-conductivity diamond substrate. This opens the door to exploring the potential of cubic-GaN devices for high-power applications, given that large area diamond substrates are becoming available.
- Open Access
- 14 November 2024
- Published by Elsevier in Materials & Design
- Vol. 248
Mechanism of novel defect multiplication impacting high power 4H-SiC devices
- 14 November 2024
- Published by Elsevier in Materials & Design
- Vol. 248
Open AccessMechanism of novel defect multiplication impacting high power 4H-SiC devices
- 1 September 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 42 (5)
Infrared optical properties of SiGeSn and GeSn layers grown by molecular beam epitaxy
The infrared optical properties of thick GeSn films (>500 nm) having 10% Sn concentration and of SiGeSn layers, utilized for the growth of strain-relieved, direct-gap GeSn films by molecular beam epitaxy, are investigated. Two growth methods are used: a graded-growth structure and a stepped-growth structure that help us to illustrate the properties of the GeSn and SiGeSn layers. Interestingly, there can be strong absorption in SiGeSn films throughout the infrared. We observe an increase in infrared absorption with increasing Sn concentration up to 21% Sn and in films, where the Sn is held constant at 18%, with increasing Si concentration up to 30%. Cavity effects in the infrared transmission measurement of stepped-growth structures are observed and associated with reflections at growth interfaces. Si–Si bond formation is proposed to occur at high Si concentrations in SiGeSn films, and the bandgap in SiGeSn films appears to decrease with increasing Si and Sn concentrations.
- 1 September 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 42 (5)
Infrared optical properties of SiGeSn and GeSn layers grown by molecular beam epitaxy
The infrared optical properties of thick GeSn films (>500 nm) having 10% Sn concentration and of SiGeSn layers, utilized for the growth of strain-relieved, direct-gap GeSn films by molecular beam epitaxy, are investigated. Two growth methods are used: a graded-growth structure and a stepped-growth structure that help us to illustrate the properties of the GeSn and SiGeSn layers. Interestingly, there can be strong absorption in SiGeSn films throughout the infrared. We observe an increase in infrared absorption with increasing Sn concentration up to 21% Sn and in films, where the Sn is held constant at 18%, with increasing Si concentration up to 30%. Cavity effects in the infrared transmission measurement of stepped-growth structures are observed and associated with reflections at growth interfaces. Si–Si bond formation is proposed to occur at high Si concentrations in SiGeSn films, and the bandgap in SiGeSn films appears to decrease with increasing Si and Sn concentrations.
- Open Access
- 22 August 2024
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 434, 105-110
Investigation of BPD Faulting under Extreme Carrier Injection in Room vs High Temperature Implanted 3.3kV SiC MOSFETs
Implantation process for high Al dose p+ contact layers in SiC MOSFETs can generate new basal plane dislocations (BPDs). Such BPD faulting under high carrier injection was investigated in SiC MOSFET layers designed for 3.3kV operation with either room temperature (RT) or high temperature (HT) implantations performed for their high dose p+ contact layer. For excess carrier injection levels of ~1x1018 cm-3 implant induced BPDs faulted from the termination regions of the MOSFETs in the case of RT samples, while the HT samples show no BPD faulting because there were no implant-induced BPDs. However, in the active region of the device no BPDs faulted for both the RT as well as HT samples even at a higher carrier injection of ~1x1019 cm-3. Technology computer-aided design (TCAD) simulations show that the lower doped p-well region below the p+ contact in the active area of the device prevents the minority electron density in the p+ contact layer to below 10x the hole density, which limits BPD faulting even when they are present in that layer as in the case of RT implanted samples.
- 22 August 2024
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 434, 105-110
Open AccessInvestigation of BPD Faulting under Extreme Carrier Injection in Room vs High Temperature Implanted 3.3kV SiC MOSFETs
Implantation process for high Al dose p+ contact layers in SiC MOSFETs can generate new basal plane dislocations (BPDs). Such BPD faulting under high carrier injection was investigated in SiC MOSFET layers designed for 3.3kV operation with either room temperature (RT) or high temperature (HT) implantations performed for their high dose p+ contact layer. For excess carrier injection levels of ~1x1018 cm-3 implant induced BPDs faulted from the termination regions of the MOSFETs in the case of RT samples, while the HT samples show no BPD faulting because there were no implant-induced BPDs. However, in the active region of the device no BPDs faulted for both the RT as well as HT samples even at a higher carrier injection of ~1x1019 cm-3. Technology computer-aided design (TCAD) simulations show that the lower doped p-well region below the p+ contact in the active area of the device prevents the minority electron density in the p+ contact layer to below 10x the hole density, which limits BPD faulting even when they are present in that layer as in the case of RT implanted samples.