Muhammad Waqas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Muhammad Waqas has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Vasileios Koutsos
School of Engineering, Institute for Materials and Processes The University of Edinburgh Edinburgh UK
4 shared publications Dipa Ray
School of Engineering, Institute for Materials and Processes The University of Edinburgh Edinburgh UK
2 shared publications- Faraz Fazal
School of Engineering Institute for Materials and Processes The University of Edinburgh Robert Stevenson Road Edinburgh EH9 3FB UK
2 shared publications - Francisco Javier Diaz Sanchez
School of Engineering, Institute for Materials and Processes, The University of Edinburgh, Robert Stevenson Road, Edinburgh, EH9 3FB, United Kingdom
2 shared publications Norbert Radacsi
School of Engineering, Institute for Materials and Processes The University of Edinburgh Edinburgh UK
2 shared publications- Norbert Radacsi
School of Engineering, Institute for Materials and Processes The University of Edinburgh Edinburgh UK
2 shared publications
Latest Publications
- Open Access
- 15 May 2025
- Published by Beilstein Institut in Beilstein Journal of Nanotechnology
- Vol. 16 (1) , 652-663
Aprepitant-loaded solid lipid nanoparticles: a novel approach to enhance oral bioavailability
Objectives of the present study are the development of aprepitant (APT)-loaded solid lipid nanoparticles (SLNs) using the polymers poloxamer 407 and β-cyclodextrin for enhanced solubility and their pharmacokinetic analysis. APT-loaded SLNs were prepared by the precipitation method and characterized by physicochemical studies including particle size and zeta potential measurements, drug content, encapsulation efficiency and solubility studies, Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray diffraction (XRD), differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), in vitro drug release in 0.1 M HCl (pH 1.2) and phosphate-buffered saline (PBS, pH 7.4), and pharmacokinetic studies. The optimal formulation (APT-CD-NP4) containing the highest concentration of β-CD showed the highest drug solubility (93.50% ± 3.73%) in PBS (pH 7.4) and drug content (96.75% ± 0.24%); particle size, zeta potential, and polydispersity index of APT-CD-NP4 were 121.1 ± 0.72 nm, −18.8 ± 0.94 mV, and 0.15 ± 0.35, respectively. SEM analysis showed that APT was converted from the crystal state into an amorphous state after SLN preparation. FTIR results indicated compatibility between APT and the polymers. XRD, TGA, and DSC results indicated no physical interaction between drug and polymers. In vitro drug release studies showed that APT-CD-NP4 yielded the maximum drug release (98.89% ± 4.11%) in PBS (pH 7.4) and followed the Higuchi release model (with exponent n = 0.542), indicating non-Fickian diffusion (anomalous transport). The maximum concentration of drug in plasma and the bioavailability of optimal formulation APT-CD-NP4 were higher than those of pure APT. Therefore, the optimal SLN formulation APT-CD-NP4 is a promising tool for oral administration with sustained release to improve the bioavailability of the BCS class-IV drug APT.
- 15 May 2025
- Published by Beilstein Institut in Beilstein Journal of Nanotechnology
- Vol. 16 (1) , 652-663
Open AccessAprepitant-loaded solid lipid nanoparticles: a novel approach to enhance oral bioavailability
Objectives of the present study are the development of aprepitant (APT)-loaded solid lipid nanoparticles (SLNs) using the polymers poloxamer 407 and β-cyclodextrin for enhanced solubility and their pharmacokinetic analysis. APT-loaded SLNs were prepared by the precipitation method and characterized by physicochemical studies including particle size and zeta potential measurements, drug content, encapsulation efficiency and solubility studies, Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray diffraction (XRD), differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), in vitro drug release in 0.1 M HCl (pH 1.2) and phosphate-buffered saline (PBS, pH 7.4), and pharmacokinetic studies. The optimal formulation (APT-CD-NP4) containing the highest concentration of β-CD showed the highest drug solubility (93.50% ± 3.73%) in PBS (pH 7.4) and drug content (96.75% ± 0.24%); particle size, zeta potential, and polydispersity index of APT-CD-NP4 were 121.1 ± 0.72 nm, −18.8 ± 0.94 mV, and 0.15 ± 0.35, respectively. SEM analysis showed that APT was converted from the crystal state into an amorphous state after SLN preparation. FTIR results indicated compatibility between APT and the polymers. XRD, TGA, and DSC results indicated no physical interaction between drug and polymers. In vitro drug release studies showed that APT-CD-NP4 yielded the maximum drug release (98.89% ± 4.11%) in PBS (pH 7.4) and followed the Higuchi release model (with exponent n = 0.542), indicating non-Fickian diffusion (anomalous transport). The maximum concentration of drug in plasma and the bioavailability of optimal formulation APT-CD-NP4 were higher than those of pure APT. Therefore, the optimal SLN formulation APT-CD-NP4 is a promising tool for oral administration with sustained release to improve the bioavailability of the BCS class-IV drug APT.
- Open Access
- 24 August 2023
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 140 (43)
Polyaniline/polyvinylpyrrolidone nanofibers via nozzle‐free electrospinning
Polyaniline (PANI) in its emeraldine base (PANI‐EB) and salt (PANI‐ES) forms was combined with polyvinylpyrrolidone (PVP) to produce nanofibers in a one‐step electrospinning process using a nozzle‐free electrospinning setup for the first time. The surface morphologies and chemical structure of the composite nanofibers were characterized by scanning electron microscopy (SEM), X‐ray diffraction (XRD), Fourier transform infrared spectroscopy—attenuated total reflectance (FTIR‐ATR), and energy‐dispersive X‐ray spectroscopy (EDX). Four PANI/PVP electrospun nanofibers with different PANI concentrations were prepared to investigate the effect of PANI concentration on the structure and properties of the nanofibers. The incorporation of different contents of PANI‐EB and PANI‐ES in the PVP solution and their impact on the fiber morphology were investigated.
- 24 August 2023
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 140 (43)
Open AccessPolyaniline/polyvinylpyrrolidone nanofibers via nozzle‐free electrospinning
Polyaniline (PANI) in its emeraldine base (PANI‐EB) and salt (PANI‐ES) forms was combined with polyvinylpyrrolidone (PVP) to produce nanofibers in a one‐step electrospinning process using a nozzle‐free electrospinning setup for the first time. The surface morphologies and chemical structure of the composite nanofibers were characterized by scanning electron microscopy (SEM), X‐ray diffraction (XRD), Fourier transform infrared spectroscopy—attenuated total reflectance (FTIR‐ATR), and energy‐dispersive X‐ray spectroscopy (EDX). Four PANI/PVP electrospun nanofibers with different PANI concentrations were prepared to investigate the effect of PANI concentration on the structure and properties of the nanofibers. The incorporation of different contents of PANI‐EB and PANI‐ES in the PVP solution and their impact on the fiber morphology were investigated.
- Open Access
- 27 August 2022
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (43)
Improving the through‐thickness electrical conductivity of carbon fiber reinforced polymer composites using interleaving conducting veils
In this study, thin carbon fiber‐based conducting veils were used as interleaving materials to improve the through‐thickness electrical conductivity of carbon fiber reinforced composites. Carbon fiber (CF) or nickel‐coated carbon fiber (NiCF) veils were used as interlayers between standard carbon fiber reinforcement fabrics. The through‐thickness electrical conductivity of the interleaved composites with CF or NiCF veils improved over 50 fold, from 0.18 to 9.47 and 9.16 S/cm, respectively, compared to the control specimens. However, the interleaved specimens exhibited a ca. 20%–24% reduction in their interlaminar shear strength (ILSS) and flexural strength. The introduction of conducting veils facilitated establishing an electrical pathway between the carbon fabric plies by reducing the non‐conducting resin rich zone in the interlaminar region. This established an electrically conductive pathway across the thickness of the laminate. This study reveals that conducting veil‐interleaved composites can meet a functional integration requirement of the aerospace sector for electrical properties, and can find applications in lightning protection, EMI shielding, and structural health monitoring.
- 27 August 2022
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (43)
Open AccessImproving the through‐thickness electrical conductivity of carbon fiber reinforced polymer composites using interleaving conducting veils
In this study, thin carbon fiber‐based conducting veils were used as interleaving materials to improve the through‐thickness electrical conductivity of carbon fiber reinforced composites. Carbon fiber (CF) or nickel‐coated carbon fiber (NiCF) veils were used as interlayers between standard carbon fiber reinforcement fabrics. The through‐thickness electrical conductivity of the interleaved composites with CF or NiCF veils improved over 50 fold, from 0.18 to 9.47 and 9.16 S/cm, respectively, compared to the control specimens. However, the interleaved specimens exhibited a ca. 20%–24% reduction in their interlaminar shear strength (ILSS) and flexural strength. The introduction of conducting veils facilitated establishing an electrical pathway between the carbon fabric plies by reducing the non‐conducting resin rich zone in the interlaminar region. This established an electrically conductive pathway across the thickness of the laminate. This study reveals that conducting veil‐interleaved composites can meet a functional integration requirement of the aerospace sector for electrical properties, and can find applications in lightning protection, EMI shielding, and structural health monitoring.
- 16 June 2021
- Published by IOP Publishing in Medical Engineering & Physics
- Vol. 94 (1) , 52-60
A modified 3D printer as a hybrid bioprinting-electrospinning system for use in vascular tissue engineering applications
There is a high demand for small diameter vascular grafts having mechanical and biological properties similar to that of living tissues. Tissue-engineered vascular grafts using current methods have often failed due to the mismatch of mechanical properties between the implanted graft and living tissues. To address this limitation, a hybrid bioprinting-electrospinning system is developed for vascular tissue engineering applications. The setup is capable of producing layered structure from electrospun fibres and cell-laden hydrogel. A Creality3D Ender 3D printer has been modified into a hybrid setup having one bioprinting head and two electrospinning heads. Fortus 250mc and Flashforge Creator Pro 3D printers were used to print parts using acrylonitrile butadiene styrene (ABS) and polylactic acid (PLA) polymers. An Arduino mega 2560 and a Ramps 1.4 controller board were selected to control the functions of the hybrid bioprinting setup. The setup was tested successfully to print a tubular construct around a rotating needle.
- 16 June 2021
- Published by IOP Publishing in Medical Engineering & Physics
- Vol. 94 (1) , 52-60
A modified 3D printer as a hybrid bioprinting-electrospinning system for use in vascular tissue engineering applications
There is a high demand for small diameter vascular grafts having mechanical and biological properties similar to that of living tissues. Tissue-engineered vascular grafts using current methods have often failed due to the mismatch of mechanical properties between the implanted graft and living tissues. To address this limitation, a hybrid bioprinting-electrospinning system is developed for vascular tissue engineering applications. The setup is capable of producing layered structure from electrospun fibres and cell-laden hydrogel. A Creality3D Ender 3D printer has been modified into a hybrid setup having one bioprinting head and two electrospinning heads. Fortus 250mc and Flashforge Creator Pro 3D printers were used to print parts using acrylonitrile butadiene styrene (ABS) and polylactic acid (PLA) polymers. An Arduino mega 2560 and a Ramps 1.4 controller board were selected to control the functions of the hybrid bioprinting setup. The setup was tested successfully to print a tubular construct around a rotating needle.
- 6 May 2021
- Published by IOP Publishing in Medical Engineering & Physics
- Vol. 92 (1) , 80-87
Design and development of a nozzle-free electrospinning device for the high-throughput production of biomaterial nanofibers
This technical note provides a step-by-step guide for the design and construction of a temperature-controlled nozzle-free electrospinning device. The equipment uses a rotating mandrel partially immersed within a polymer solution to produce fibers in an upward motion by inducing the formation of multiple Taylor cones and subsequently multi-jetting out of an electrified open surface. Free-surface electrospinning can overcome limitations and drawbacks associated with single and multi-nozzle spinneret configurations, such as low yield, limited production capacity, nonuniform electric field distribution, and clogging. Most importantly, this lab-scaled high-throughput device can provide an alternative economical route for needleless electrospinning research, in contrast to the high costs associated with industrially available upscaling equipment. Among the device's technical specifications, a key feature is a cryo-collector mandrel, capable of collecting fibers in sub-zero temperatures, which can induce ultra-porous nanostructures, wider pores, and subsequent in-depth penetration of cells. A multi-channel gas chamber allows the conditioning of the atmosphere, temperature, and airflow, while the chamber's design averts user exposure to the high-voltage components. All the Computer-Aided Design (CAD) files and point-by-point assembly instructions, along with a list of the materials used, are provided.
- 6 May 2021
- Published by IOP Publishing in Medical Engineering & Physics
- Vol. 92 (1) , 80-87
Design and development of a nozzle-free electrospinning device for the high-throughput production of biomaterial nanofibers
This technical note provides a step-by-step guide for the design and construction of a temperature-controlled nozzle-free electrospinning device. The equipment uses a rotating mandrel partially immersed within a polymer solution to produce fibers in an upward motion by inducing the formation of multiple Taylor cones and subsequently multi-jetting out of an electrified open surface. Free-surface electrospinning can overcome limitations and drawbacks associated with single and multi-nozzle spinneret configurations, such as low yield, limited production capacity, nonuniform electric field distribution, and clogging. Most importantly, this lab-scaled high-throughput device can provide an alternative economical route for needleless electrospinning research, in contrast to the high costs associated with industrially available upscaling equipment. Among the device's technical specifications, a key feature is a cryo-collector mandrel, capable of collecting fibers in sub-zero temperatures, which can induce ultra-porous nanostructures, wider pores, and subsequent in-depth penetration of cells. A multi-channel gas chamber allows the conditioning of the atmosphere, temperature, and airflow, while the chamber's design averts user exposure to the high-voltage components. All the Computer-Aided Design (CAD) files and point-by-point assembly instructions, along with a list of the materials used, are provided.