Gonzalo Eduardo López Villacís
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Gonzalo Eduardo López Villacís has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Segundo Manuel Espín Lagos
Universidad Técnica de Ambato, Ambato, Ecuador
3 shared publications - Martha Sevilla
Facultad de Ingeniería en Sistemas, Electrónica e Industrial, Carrera de Telecomunicaciones, Universidad Técnica de Ambato, Ambato 180207, Ecuador
2 shared publications - Pablo Raúl Valle Velasco
Facultad de Ingeniería Civil y Mecánica, Carrera de Ingeniería Mecánica, Universidad Técnica de Ambato, Ambato 180207, Ecuador
2 shared publications - César Hernán Arroba Arroba
Faculty of Civil and Mechanical Engineering, Universidad Técnica de Ambato, Ambato 180206, Ecuador
1 shared publication - Diana Belén Peralta Zurita
Universidad Internacional SEK-Ecuador. Quito, Ecuador
1 shared publication - Diego Rafael Freire Romero
Universidad Técnica de Ambato
1 shared publication
Latest Publications
- Open Access
- 3 July 2026
- Published by Editorial Ciencia Innovadora in Revista Ciencia Innovadora
- Vol. 4 (3) , 01-16
Análisis comparativo de métodos para el cálculo de la constante elástica en resortes de compresión helicoidales
Compression helical springs are critical components in pressure control systems. However, classical analytical formulations present significant limitations by not accounting for effects such as contact, friction, and geometric non-linearities, which can lead to substantial errors in stiffness prediction. This study addresses this issue through an experimental and numerical characterisation of a compression helical spring made from EN 10270-1 SH steel, designed for use in pressure control valves. The elastic constant was determined experimentally by means of standardised tensile tests (ASTM E8/E8M), yielding a value of k = 42.38 N/mm and a restoring force of F = 423.80 N. These values were compared with the results of analytical models (classical theory and Wahl's correction) and with finite element simulations under linear and non-linear static configurations with self-contact (code NE3, μ = 0.15). The results show that the classical formulation overestimates stiffness by 8.28%, whilst Wahl's correction underestimates it by 16.26%. Case NE3 provides the closest agreement with the experimental values, confirming its suitability for modelling helical springs under axial load. It was further verified that the spring operates within the elastic regime throughout the entire range of compression analysed. The methodology developed constitutes a reliable tool for the design of such components in pressure-regulation systems.
- 3 July 2026
- Published by Editorial Ciencia Innovadora in Revista Ciencia Innovadora
- Vol. 4 (3) , 01-16
Open AccessAnálisis comparativo de métodos para el cálculo de la constante elástica en resortes de compresión helicoidales
Compression helical springs are critical components in pressure control systems. However, classical analytical formulations present significant limitations by not accounting for effects such as contact, friction, and geometric non-linearities, which can lead to substantial errors in stiffness prediction. This study addresses this issue through an experimental and numerical characterisation of a compression helical spring made from EN 10270-1 SH steel, designed for use in pressure control valves. The elastic constant was determined experimentally by means of standardised tensile tests (ASTM E8/E8M), yielding a value of k = 42.38 N/mm and a restoring force of F = 423.80 N. These values were compared with the results of analytical models (classical theory and Wahl's correction) and with finite element simulations under linear and non-linear static configurations with self-contact (code NE3, μ = 0.15). The results show that the classical formulation overestimates stiffness by 8.28%, whilst Wahl's correction underestimates it by 16.26%. Case NE3 provides the closest agreement with the experimental values, confirming its suitability for modelling helical springs under axial load. It was further verified that the spring operates within the elastic regime throughout the entire range of compression analysed. The methodology developed constitutes a reliable tool for the design of such components in pressure-regulation systems.
- Open Access
Hydraulic Characterization of a Direct-Acting Pressure-Reducing Valve Using CFD and Experimental Validation
This study presents the hydraulic characterization of a direct-acting pressure-reducing valve (PRV) using a combined experimental and numerical approach. An experimental test bench was implemented to measure inlet, control port, and outlet pressures over a flow rate range from 0 to 4.0 m3/h, under a constant inlet pressure of 8 bar and a set pressure of 3 bar. In parallel, a three-dimensional steady-state CFD model was developed using a sequential force balance analysis between hydraulic and spring restoring forces. The results show good agreement between numerical predictions and experimental data, with a maximum error below 10% in outlet pressure. The pressure drop exhibited a nonlinear increasing trend with flow rate, reaching values close to 1.8 bar at 4.0 m3/h. The flow coefficient Kv remained within a range of 2.2–3.0, while the pressure regulation coefficient S remained below 0.05, indicating stable regulation performance. Additional simulations at 25 bar provided improved agreement with manufacturer data, suggesting that catalog curves may be based on nominal pressure conditions. The proposed methodology demonstrates that steady-state CFD coupled with force balance analysis is an effective and computationally efficient approach for predicting the hydraulic behavior of direct-acting PRVs.
Open AccessHydraulic Characterization of a Direct-Acting Pressure-Reducing Valve Using CFD and Experimental Validation
This study presents the hydraulic characterization of a direct-acting pressure-reducing valve (PRV) using a combined experimental and numerical approach. An experimental test bench was implemented to measure inlet, control port, and outlet pressures over a flow rate range from 0 to 4.0 m3/h, under a constant inlet pressure of 8 bar and a set pressure of 3 bar. In parallel, a three-dimensional steady-state CFD model was developed using a sequential force balance analysis between hydraulic and spring restoring forces. The results show good agreement between numerical predictions and experimental data, with a maximum error below 10% in outlet pressure. The pressure drop exhibited a nonlinear increasing trend with flow rate, reaching values close to 1.8 bar at 4.0 m3/h. The flow coefficient Kv remained within a range of 2.2–3.0, while the pressure regulation coefficient S remained below 0.05, indicating stable regulation performance. Additional simulations at 25 bar provided improved agreement with manufacturer data, suggesting that catalog curves may be based on nominal pressure conditions. The proposed methodology demonstrates that steady-state CFD coupled with force balance analysis is an effective and computationally efficient approach for predicting the hydraulic behavior of direct-acting PRVs.
- 1 April 2026
- Published by Springer Nature
- p. 581-595
Influence of Engine Position on Resistance in Long-Distance Bus Rollover
- 1 April 2026
- Published by Springer Nature
- p. 581-595
Influence of Engine Position on Resistance in Long-Distance Bus Rollover
- Open Access
- 1 June 2025
- Published by Polo de Capacitacion, Investigacion y Publicacion in Polo del Conocimiento
- Vol. 10 (6) , 2692-2712
Análisis energético y exergético de procesos de manufactura automatizados en la industria 4.0: Un enfoque integral
El artículo científico analiza el consumo energético y relacionado con la energía de los procesos de fabricación automatizados en el contexto de la Industria 4.0, con un enfoque integrado centrado en la optimización del rendimiento termodinámico y la sostenibilidad operativa. La parte de investigación parte del reconocimiento del alto consumo energético de los sistemas fabricados digitalmente, que, si bien maximizan la productividad, pueden resultar en pérdidas energéticas significativas si no se gestionan de forma inteligente. El objetivo principal del estudio es comparar la eficiencia energética y la pérdida de energía en varias configuraciones de líneas de producción automatizadas, integrando tecnologías como Internet de las cosas (IoT), herramientas digitales y aprendizaje automático para la gestión térmica avanzada. Desde un punto de vista teórico, se adoptan los fundamentos de la termodinámica y la exergía como herramientas esenciales para cuantificar tanto la energía útil como las irreversibilidades del sistema, incorporando también énfasis en la ingeniería de sistemas de economía circular. Concluyó que un enfoque de ejercicio combinado con herramientas digitales de la Industria 4.0 no solo aumenta la eficiencia energética, sino que también sirve como un camino estratégico hacia la competitividad industrial y la sostenibilidad energética en entornos de producción avanzados. Se sugiere investigar la integración del análisis del ejercicio con sistemas adaptativos asistidos por computadora.
- 1 June 2025
- Published by Polo de Capacitacion, Investigacion y Publicacion in Polo del Conocimiento
- Vol. 10 (6) , 2692-2712
Open AccessAnálisis energético y exergético de procesos de manufactura automatizados en la industria 4.0: Un enfoque integral
El artículo científico analiza el consumo energético y relacionado con la energía de los procesos de fabricación automatizados en el contexto de la Industria 4.0, con un enfoque integrado centrado en la optimización del rendimiento termodinámico y la sostenibilidad operativa. La parte de investigación parte del reconocimiento del alto consumo energético de los sistemas fabricados digitalmente, que, si bien maximizan la productividad, pueden resultar en pérdidas energéticas significativas si no se gestionan de forma inteligente. El objetivo principal del estudio es comparar la eficiencia energética y la pérdida de energía en varias configuraciones de líneas de producción automatizadas, integrando tecnologías como Internet de las cosas (IoT), herramientas digitales y aprendizaje automático para la gestión térmica avanzada. Desde un punto de vista teórico, se adoptan los fundamentos de la termodinámica y la exergía como herramientas esenciales para cuantificar tanto la energía útil como las irreversibilidades del sistema, incorporando también énfasis en la ingeniería de sistemas de economía circular. Concluyó que un enfoque de ejercicio combinado con herramientas digitales de la Industria 4.0 no solo aumenta la eficiencia energética, sino que también sirve como un camino estratégico hacia la competitividad industrial y la sostenibilidad energética en entornos de producción avanzados. Se sugiere investigar la integración del análisis del ejercicio con sistemas adaptativos asistidos por computadora.
- 1 May 2021
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 885, 11-16
Hardness Evaluation of 88Cu-4Pb-4Sn-4Zn Alloy by Mechanical Alloying with Oxidizing Atmosphere
The investigation of new materials that have properties such as resistance to high temperatures, wear resistance, rigidity, and low weight, involves the use of technological processes with more and more advantages. For this purpose, mechanical alloying is a widely used technique, which consist of high-energy impact between balls inside a container, where constant collisions deform and fracture the material, achieving the alloy of the particles in a solid state. This work focuses on the Vickers hardness evaluation of the copper matrix alloy with 4% Pb, 4% Sn and 4% Zn, in an oxidizing atmosphere, sintered at 800 °C and 900 °C, using milling times of 3 hours, 6 hours and 9 hours. The results show that there is a relationship between the hardness obtained, in the two groups of specimens at 800 ° C and 900 ° C, with the grinding time and the sintering temperature, among others used in the process. An average maximum hardness of 53.4 HV was obtained.
- 1 May 2021
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 885, 11-16
Hardness Evaluation of 88Cu-4Pb-4Sn-4Zn Alloy by Mechanical Alloying with Oxidizing Atmosphere
The investigation of new materials that have properties such as resistance to high temperatures, wear resistance, rigidity, and low weight, involves the use of technological processes with more and more advantages. For this purpose, mechanical alloying is a widely used technique, which consist of high-energy impact between balls inside a container, where constant collisions deform and fracture the material, achieving the alloy of the particles in a solid state. This work focuses on the Vickers hardness evaluation of the copper matrix alloy with 4% Pb, 4% Sn and 4% Zn, in an oxidizing atmosphere, sintered at 800 °C and 900 °C, using milling times of 3 hours, 6 hours and 9 hours. The results show that there is a relationship between the hardness obtained, in the two groups of specimens at 800 ° C and 900 ° C, with the grinding time and the sintering temperature, among others used in the process. An average maximum hardness of 53.4 HV was obtained.