Nasir Shahin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Nasir Shahin has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Akbar Heidarpour
Department of Metallurgy and Materials Engineering, Hamedan University of Technology, Hamedan, Iran
2 shared publications Farzad Soleymani
2 shared publicationsSh. Kazemi
2 shared publicationsAkbar Heidarpour
Department of Metallurgy and Materials Engineering Hamedan University of Technology Hamedan Iran
1 shared publicationFakhreddin Ashrafizadeh
1 shared publication- Hoda Asadipour
Department of Materials Engineering, Isfahan University of Technology, Isfahan, Iran
1 shared publication
Latest Publications
- 3 July 2025
- Published by Wiley in Journal of Biomedical Materials Research Part A
- Vol. 113 (7) , e37953
Biological Responses and Hemocompatibility of Diamond‐Like Carbon Thin Films on Different PEO Interlayers for Potential Cardiovascular Stent Applications
Plasma electrolytic oxidation (PEO) considerably affects controlling the degradation rate of magnesium‐based implants to approach the healing period. However, the biological properties still require further improvement, particularly for blood‐contact applications, such as cardiovascular stents. This research aims to study in vitro biological properties of the duplex diamond‐like carbon (DLC)/plasma electrolytic oxidation (PEO) coatings as a function of various PEO middle layers for potential cardiovascular stent applications. To this aim, two different PEO coatings including silicate and phosphate compounds were applied on AZ31 substrate as middle‐layers, and a top DLC layer with 1 μm thickness was successfully synthesized on them. Moreover, the role of different PEO interlayers on the degradation behavior, biocompatibility, hemocompatibility, and its mechanism are studied. Results showed a considerable decrease in degradation rate after applying the PEO process and the PEO‐Ph revealed the optimized degradation performance in just PEO‐coated samples. On the other side, the best degradation performance between duplex‐coated samples was obtained for DLC/PEO‐Si according to its higher diamond‐like structure. Moreover, the viability of human umbilical vein endothelial cells on DLC/PEO‐Ph was higher than that of the DLC/PEO‐Si, which might be attributed to higher protein adsorption on its surface. In the case of hemocompatibility, a considerable decrease in hemolysis ratio along with remarkable improvement in clotting behavior was observed by applying the PEO process. However, the hemolysis ratio was reduced as being safe for blood‐contact applications just for duplex‐coated samples. In conclusion, a promising coating for blood‐contact applications based on DLC/PEO in particular in the case of DLC/PEO‐Si has been provided in this study.
- 3 July 2025
- Published by Wiley in Journal of Biomedical Materials Research Part A
- Vol. 113 (7) , e37953
Biological Responses and Hemocompatibility of Diamond‐Like Carbon Thin Films on Different PEO Interlayers for Potential Cardiovascular Stent Applications
Plasma electrolytic oxidation (PEO) considerably affects controlling the degradation rate of magnesium‐based implants to approach the healing period. However, the biological properties still require further improvement, particularly for blood‐contact applications, such as cardiovascular stents. This research aims to study in vitro biological properties of the duplex diamond‐like carbon (DLC)/plasma electrolytic oxidation (PEO) coatings as a function of various PEO middle layers for potential cardiovascular stent applications. To this aim, two different PEO coatings including silicate and phosphate compounds were applied on AZ31 substrate as middle‐layers, and a top DLC layer with 1 μm thickness was successfully synthesized on them. Moreover, the role of different PEO interlayers on the degradation behavior, biocompatibility, hemocompatibility, and its mechanism are studied. Results showed a considerable decrease in degradation rate after applying the PEO process and the PEO‐Ph revealed the optimized degradation performance in just PEO‐coated samples. On the other side, the best degradation performance between duplex‐coated samples was obtained for DLC/PEO‐Si according to its higher diamond‐like structure. Moreover, the viability of human umbilical vein endothelial cells on DLC/PEO‐Ph was higher than that of the DLC/PEO‐Si, which might be attributed to higher protein adsorption on its surface. In the case of hemocompatibility, a considerable decrease in hemolysis ratio along with remarkable improvement in clotting behavior was observed by applying the PEO process. However, the hemolysis ratio was reduced as being safe for blood‐contact applications just for duplex‐coated samples. In conclusion, a promising coating for blood‐contact applications based on DLC/PEO in particular in the case of DLC/PEO‐Si has been provided in this study.
- 16 December 2023
- Published by Elsevier in Materials Letters
- Vol. 357
The effect of surface energy on the wettability of graphene-coated copper: A comparison of different single and multilayer graphene
- 16 December 2023
- Published by Elsevier in Materials Letters
- Vol. 357
The effect of surface energy on the wettability of graphene-coated copper: A comparison of different single and multilayer graphene
- Open Access
- 13 November 2023
- Published by Wiley in Engineering Reports
- Vol. 6 (8)
The purity evolution of Ti3AlC2 MAX phase synthesized by mechanochemical route: The effect of Al content and high‐temperature annealing
This study explores the effects of excess Al and annealing at high temperature on the purity of Ti3AlC2 MAX phase synthesized by the mechanochemical route. In this regard, a constant stoichiometric ratio of Ti: Al: C = 3: 1: 2 along with three blends of nonstoichiometric ratios with excess Al (Ti: Al: C = 3: X: 2, X = 1.1, 1.2, and 1.5) were ball milled. Then, to examine the annealing at high‐temperature effects, the compacted ball‐milled powders were heated at 900 and 1200°C for 1 h. The phase identification revealed that 10 h of ball milling caused a reaction between the elemental powders, and Ti3AlC2 and TiC were formed. The mechanism of the reaction during the high‐energy ball milling process is assigned to a mechanically induced self‐propagating reaction. Addition of excess Al to primary powders caused to increase the purity of Ti3AlC2 significantly. Furthermore, annealing at high temperature leading to complete reactions of the ball‐milled powders and increased Ti3AlC2 purity. The maximum Ti3AlC2 content of 88% was obtained of initial powder of Ti: Al: C = 3: 1.2: 2 ratio after annealing at 1200°C.
- 13 November 2023
- Published by Wiley in Engineering Reports
- Vol. 6 (8)
Open AccessThe purity evolution of Ti3AlC2 MAX phase synthesized by mechanochemical route: The effect of Al content and high‐temperature annealing
This study explores the effects of excess Al and annealing at high temperature on the purity of Ti3AlC2 MAX phase synthesized by the mechanochemical route. In this regard, a constant stoichiometric ratio of Ti: Al: C = 3: 1: 2 along with three blends of nonstoichiometric ratios with excess Al (Ti: Al: C = 3: X: 2, X = 1.1, 1.2, and 1.5) were ball milled. Then, to examine the annealing at high‐temperature effects, the compacted ball‐milled powders were heated at 900 and 1200°C for 1 h. The phase identification revealed that 10 h of ball milling caused a reaction between the elemental powders, and Ti3AlC2 and TiC were formed. The mechanism of the reaction during the high‐energy ball milling process is assigned to a mechanically induced self‐propagating reaction. Addition of excess Al to primary powders caused to increase the purity of Ti3AlC2 significantly. Furthermore, annealing at high temperature leading to complete reactions of the ball‐milled powders and increased Ti3AlC2 purity. The maximum Ti3AlC2 content of 88% was obtained of initial powder of Ti: Al: C = 3: 1.2: 2 ratio after annealing at 1200°C.
- 28 August 2023
- Published by Elsevier in Materials Letters
- Vol. 352
Cellular behavior and antibacterial properties of MAO/PCL-chitosan-nanobaghdadite composite coating on biodegradable AZ91 alloy
- 28 August 2023
- Published by Elsevier in Materials Letters
- Vol. 352
Cellular behavior and antibacterial properties of MAO/PCL-chitosan-nanobaghdadite composite coating on biodegradable AZ91 alloy
- 1 April 2017
- Published by Elsevier in International Journal of Refractory Metals and Hard Materials
- Vol. 64, 1-6
A novel approach to in situ synthesis of WC-Al2O3 composite by high energy reactive milling
- 1 April 2017
- Published by Elsevier in International Journal of Refractory Metals and Hard Materials
- Vol. 64, 1-6
A novel approach to in situ synthesis of WC-Al2O3 composite by high energy reactive milling
- 1 July 2016
- Published by Elsevier in Advanced Powder Technology
- Vol. 27 (4) , 1775-1780
Mechanochemical synthesis mechanism of Ti 3 AlC 2 MAX phase from elemental powders of Ti, Al and C
- 1 July 2016
- Published by Elsevier in Advanced Powder Technology
- Vol. 27 (4) , 1775-1780
Mechanochemical synthesis mechanism of Ti 3 AlC 2 MAX phase from elemental powders of Ti, Al and C