Marten Darmawan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Marten Darmawan has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Doyoung Byun
Department of Mechanical Engineering, Sungkyunkwan University, 2066 Seobu-Ro, Jangan-Gu, Suwon-Si 16419, Republic of Korea
2 shared publications Jihoon Kim
Coastal and Environmental Engineering Division, Korea Institute of Ocean Science and Technology, Ansan, Sangnok-gu, Gyeonggi-do, Republic of Korea
2 shared publications- Amir Faisal
Teknik Biomedik, Institut Teknologi Sumatera, Lampung Selatan
1 shared publication - Arka Dwinanda Soewono
Universitas Katolik Indonesia Atma Jaya
1 shared publication - Chi Won Ahn
Advanced Technology Center for Information Electronic Materials and Components, National Nanofab Center, Daejeon, Korea
1 shared publication Djoko Setyanto
Professional Engineer Certification, Atma Jaya Catholic University of Indonesia, Jakarta, Indonesia
1 shared publication
Latest Publications
- Open Access
- 11 September 2025
- Published by University of Porto in U.Porto Journal of Engineering
- Vol. 11 (2) , 62-81
Techno-Economic Analysis of a Low-Cost Hybrid Heat Sink-Fan Cooling System for Solar Photovoltaic Panel: Case Study in West Java, Indonesia
Rising temperatures can negatively impact the performance of solar photovoltaic (PV) systems. To address this issue, a hybrid passive and active cooling for PV panels presents a viable solution to reduce excessive heating. However, only a few studies have assessed the economic viability of these hybrid PV cooling techniques. The purpose of this study is to examine the effect of a low-cost heat sink-fan cooling on the PV panel surface temperature and conversion efficiency, and analyze the production cost effectiveness factor (FCE) to assess the cooling system's performance. A comparative analysis found that the average surface temperature of the PV panel with a cooler was 11.97°C when exposed to solar irradiance of approximately 1,000 W/m2 and 9.73°C lower at around 800 W/m2 compared to the regular PV panel. This reduction in temperature led to an increase in the output voltage, current, and power in the solar PV with the cooler. The addition of heat sink-fan cooling yielded a 0.89 % to 1.02% improvement in the conversion efficiency of the PV module, depending on the intensity of the solar irradiation. The economic analysis based on the production cost effectiveness factor discovered that the mean value of the FCE for the hybrid heat-sink cooler ranged from 1.32 to 1.57. Since the FCE is greater than 1, the current heat sink-fan cooling system is considered cost-ineffective, indicating that further design improvements are necessary.
- 11 September 2025
- Published by University of Porto in U.Porto Journal of Engineering
- Vol. 11 (2) , 62-81
Open AccessTechno-Economic Analysis of a Low-Cost Hybrid Heat Sink-Fan Cooling System for Solar Photovoltaic Panel: Case Study in West Java, Indonesia
Rising temperatures can negatively impact the performance of solar photovoltaic (PV) systems. To address this issue, a hybrid passive and active cooling for PV panels presents a viable solution to reduce excessive heating. However, only a few studies have assessed the economic viability of these hybrid PV cooling techniques. The purpose of this study is to examine the effect of a low-cost heat sink-fan cooling on the PV panel surface temperature and conversion efficiency, and analyze the production cost effectiveness factor (FCE) to assess the cooling system's performance. A comparative analysis found that the average surface temperature of the PV panel with a cooler was 11.97°C when exposed to solar irradiance of approximately 1,000 W/m2 and 9.73°C lower at around 800 W/m2 compared to the regular PV panel. This reduction in temperature led to an increase in the output voltage, current, and power in the solar PV with the cooler. The addition of heat sink-fan cooling yielded a 0.89 % to 1.02% improvement in the conversion efficiency of the PV module, depending on the intensity of the solar irradiation. The economic analysis based on the production cost effectiveness factor discovered that the mean value of the FCE for the hybrid heat-sink cooler ranged from 1.32 to 1.57. Since the FCE is greater than 1, the current heat sink-fan cooling system is considered cost-ineffective, indicating that further design improvements are necessary.
- Open Access
- 20 November 2015
- Published by Taylor & Francis in Aerosol Science and Technology
- Vol. 49 (12) , 1271-1280
Rapid and Sustainable Surface Acoustic Wave Atomizer
Surface acoustic waves have considerable potential to rapidly generate micron to submicron sized aerosols due to the capillary wave at the liquid–air interfacial boundary. The atomization process, however, is often found to be unstable and discontinuous due to the inconsistency of the droplet position and the lack of accuracy of resonance frequency, resulting in less efficient atomization performance. We developed a rapid and sustainable surface acoustic wave (SAW) atomizer to generate aerosols in a robust, straightforward, and stable mechanism for a continuous, consistent, and reliable deposition of a functional material (i.e., poly(3,4-ethylenedioxythiophene) polystyrene sulfonate [PEDOT:PSS]). Two identical progressive focused surface acoustic wave devices were arranged in angles and in opposite directions with 1 mm wide opening to regulate appropriate amount of liquid sample to be atomized. Several parametrical studies (i.e., on the design of the SAW device, liquid flow rate, applied voltage, and deposition distance) were conducted to quantitatively characterize the performance of the atomizing system. Furthermore, the aerosol size was quantitatively measured and presented as the particle size distribution based on field emission scanning electron microscope (FESEM) images using an image processing method. The results showed that the atomizer is conclusive in demonstrating a continuous, rapid, and consistent atomization performance as an alternative and promising spray method. Copyright © 2015 American Association for Aerosol Research
- 20 November 2015
- Published by Taylor & Francis in Aerosol Science and Technology
- Vol. 49 (12) , 1271-1280
Open AccessRapid and Sustainable Surface Acoustic Wave Atomizer
Surface acoustic waves have considerable potential to rapidly generate micron to submicron sized aerosols due to the capillary wave at the liquid–air interfacial boundary. The atomization process, however, is often found to be unstable and discontinuous due to the inconsistency of the droplet position and the lack of accuracy of resonance frequency, resulting in less efficient atomization performance. We developed a rapid and sustainable surface acoustic wave (SAW) atomizer to generate aerosols in a robust, straightforward, and stable mechanism for a continuous, consistent, and reliable deposition of a functional material (i.e., poly(3,4-ethylenedioxythiophene) polystyrene sulfonate [PEDOT:PSS]). Two identical progressive focused surface acoustic wave devices were arranged in angles and in opposite directions with 1 mm wide opening to regulate appropriate amount of liquid sample to be atomized. Several parametrical studies (i.e., on the design of the SAW device, liquid flow rate, applied voltage, and deposition distance) were conducted to quantitatively characterize the performance of the atomizing system. Furthermore, the aerosol size was quantitatively measured and presented as the particle size distribution based on field emission scanning electron microscope (FESEM) images using an image processing method. The results showed that the atomizer is conclusive in demonstrating a continuous, rapid, and consistent atomization performance as an alternative and promising spray method. Copyright © 2015 American Association for Aerosol Research
- 16 October 2014
- Published by Springer Nature in Microfluidics and Nanofluidics
- Vol. 18 (5-6) , 1107-1114
Focused surface acoustic wave induced jet formation on superhydrophobic surfaces
- 16 October 2014
- Published by Springer Nature in Microfluidics and Nanofluidics
- Vol. 18 (5-6) , 1107-1114
Focused surface acoustic wave induced jet formation on superhydrophobic surfaces
- 22 November 2013
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 205, 177-185
Deposition of poly(3,4-ethylenedioxythiophene)–poly(styrenesulfonate) (PEDOT-PSS) particles using standing surface acoustic waves and electrostatic deposition method for the rapid fabrication of transparent conductive film
- 22 November 2013
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 205, 177-185
Deposition of poly(3,4-ethylenedioxythiophene)–poly(styrenesulfonate) (PEDOT-PSS) particles using standing surface acoustic waves and electrostatic deposition method for the rapid fabrication of transparent conductive film
- 12 March 2013
- Published by IOP Publishing in Nanotechnology
- Vol. 24 (13) , 135704
Electrical property measurements of metallized flagella-templated silica nanotube networks
We present an improvement in the electrical properties of silica nanotubes by coating metal nanoparticles on their surfaces. The silica nanotubes are formed from bacterial flagella bio-templates having a tubular structure. Successive depositions of metal nanoparticles on the silica nanotubes are performed through easily functionalized silica surfaces. The results show uniform metal nanoparticle sizes and a high surface area coverage. By incorporating gold, palladium and iron oxide nanoparticles, the metallized silica nanotubes gain electrical properties with the potential to create unique nanoelectronic materials. In this study, the metallized silica nanotubes with network structures are aligned and their electrical behaviors are investigated in both dry and wet conditions. The metallized silica nanotubes are found to be electrically conductive along the network structures. The current-voltage characteristics show remarkably improved electrical conductivities depending on the type of metal nanoparticle loading and nanotube network concentration.
- 12 March 2013
- Published by IOP Publishing in Nanotechnology
- Vol. 24 (13) , 135704
Electrical property measurements of metallized flagella-templated silica nanotube networks
We present an improvement in the electrical properties of silica nanotubes by coating metal nanoparticles on their surfaces. The silica nanotubes are formed from bacterial flagella bio-templates having a tubular structure. Successive depositions of metal nanoparticles on the silica nanotubes are performed through easily functionalized silica surfaces. The results show uniform metal nanoparticle sizes and a high surface area coverage. By incorporating gold, palladium and iron oxide nanoparticles, the metallized silica nanotubes gain electrical properties with the potential to create unique nanoelectronic materials. In this study, the metallized silica nanotubes with network structures are aligned and their electrical behaviors are investigated in both dry and wet conditions. The metallized silica nanotubes are found to be electrically conductive along the network structures. The current-voltage characteristics show remarkably improved electrical conductivities depending on the type of metal nanoparticle loading and nanotube network concentration.
- 1 November 2010
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 49 (11) , 113205-113205-9
Quantitative low-cost webcam-based microscopy
Digital web cameras (popularly known as webcams) have recently gained a significant increase of relevance in the field of optical microscopy, in particular to allow for quick and do-it-yourself methods in developing low-cost and portable microscopes suitable for life sciences and engineering applications in low-resource areas. Unfortunately, these methods were published without any systematic explanation and quantitative assessment of the imaging performances. We reproduce these do-it-yourself methods, discuss the optical considerations that are relevant for them, and quantitatively compare their imaging performances to a commercial digital microscope in order to clarify both the advantages and disadvantages of the webcam-based microscopes.
- 1 November 2010
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 49 (11) , 113205-113205-9
Quantitative low-cost webcam-based microscopy
Digital web cameras (popularly known as webcams) have recently gained a significant increase of relevance in the field of optical microscopy, in particular to allow for quick and do-it-yourself methods in developing low-cost and portable microscopes suitable for life sciences and engineering applications in low-resource areas. Unfortunately, these methods were published without any systematic explanation and quantitative assessment of the imaging performances. We reproduce these do-it-yourself methods, discuss the optical considerations that are relevant for them, and quantitatively compare their imaging performances to a commercial digital microscope in order to clarify both the advantages and disadvantages of the webcam-based microscopes.