Xiao Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xiao Sun has a total of 75 co-authors. Here are the top co-authors by number of shared publications:
- Hidetsugu Terada
University of Yamanashi
11 shared publications - Koji Makino
University of Yamanashi
10 shared publications - Kazuyoshi Ishida
University of Yamanashi
8 shared publications Takashi Matsuzawa
Faculty of Science and Engineering, Waseda University, Tokyo, Japan
4 shared publications- Atsuo Takanishi
Waseda University
3 shared publications - Kenji Hashimoto
Graduate School of Information, Production and Systems, Waseda University, Kitakyushu 808-0135, Japan
3 shared publications
Latest Publications
- 14 September 2026
- Published by Springer Nature
- p. 504-514
Collision Avoidance for a Heterogeneous Multi-robot Arm System by 3D-Extended Buffered Voronoi Cells
- 14 September 2026
- Published by Springer Nature
- p. 504-514
Collision Avoidance for a Heterogeneous Multi-robot Arm System by 3D-Extended Buffered Voronoi Cells
- 5 October 2025
- Published by Springer Nature
- p. 3-13
Improved Design of an Assistive Actuator for Hip Joint with Spiral-Spring/Motor Hybrid Mechanism
- 5 October 2025
- Published by Springer Nature
- p. 3-13
Improved Design of an Assistive Actuator for Hip Joint with Spiral-Spring/Motor Hybrid Mechanism
- Open Access
Development of a Rehabilitation Apparatus for Frozen Shoulder Enabling Total Motion of Shoulder Complex
This article describes an apparatus developed by the authors as a substitution for physical therapists regarding mechanical movements in the rehabilitation of frozen shoulder. In particular, the performance of this apparatus is improved in comparison with existing methods in terms of the following two major points: (1) realization of individual rehabilitation for the patient’s scapula by an innovative parallel–serial hybrid linkage design and supporting parts that can fix and move the patient’s scapula; and (2) the addition of a “teaching” and “playback” mode to enable the apparatus to record the motion of rehabilitation, allowing it to be customized for each patient by physical therapists and reproduce the recorded motion accurately, thus freeing physical therapists from repetitive rehabilitation routines. With the introduction of the whole system, experimental results are shown and discussed to verify and evaluate the performance of the developed apparatus.
Open AccessDevelopment of a Rehabilitation Apparatus for Frozen Shoulder Enabling Total Motion of Shoulder Complex
This article describes an apparatus developed by the authors as a substitution for physical therapists regarding mechanical movements in the rehabilitation of frozen shoulder. In particular, the performance of this apparatus is improved in comparison with existing methods in terms of the following two major points: (1) realization of individual rehabilitation for the patient’s scapula by an innovative parallel–serial hybrid linkage design and supporting parts that can fix and move the patient’s scapula; and (2) the addition of a “teaching” and “playback” mode to enable the apparatus to record the motion of rehabilitation, allowing it to be customized for each patient by physical therapists and reproduce the recorded motion accurately, thus freeing physical therapists from repetitive rehabilitation routines. With the introduction of the whole system, experimental results are shown and discussed to verify and evaluate the performance of the developed apparatus.
- 27 September 2024
- Published by Springer Nature
- p. 166-175
Development of a Rehabilitation Robot for the Frozen Shoulder Considering Shoulder Girdle Motion
- 27 September 2024
- Published by Springer Nature
- p. 166-175
Development of a Rehabilitation Robot for the Frozen Shoulder Considering Shoulder Girdle Motion
- 31 August 2024
- Published by Springer Nature
- p. 40-50
Improved Design of a Discontinuous Shaped Roller-Chain Drive-Type Wave Motion Reducer
- 31 August 2024
- Published by Springer Nature
- p. 40-50
Improved Design of a Discontinuous Shaped Roller-Chain Drive-Type Wave Motion Reducer
- 11 January 2024
- Published by Royal Society of Chemistry (RSC) in Lab on a Chip
- Vol. 24 (4) , 896-903
A liquid metal based, integrated parallel electroosmotic micropump cluster drive system
The application of liquid metal in a microfluidic system enables the fabrication of highly integrated on-chip electroosmotic micropumps (EOPs). In this work, a low-voltage driveable integrated parallel EOP cluster drive system is proposed. This system consists of two layers, a branch-channel layer and a trunk-channel layer. The lower branch-channel layer contains separate parallel pumping channels and a pair of comb liquid metal electrodes. The separated branch channels are connected together through the trunk channels in the upper layer. With this structural arrangement, the parallel micropumps form an integrated micropump cluster for larger pumping capacity. The distance between the pumping channel and the electrode next to it is controlled to 20 μm. To guide the pump design, parametric studies are performed and fully discussed. According to the experimental results, the micropump cluster can be driven at a low voltage of 0.5 V, and the flow rate reaches 274 nL min−1 at 5 V. In addition, the paper finally proposes an electrode protection strategy and an integrated pump-valve drive system which is expected to solve the shortcoming of electroosmotic pumps in terms of long-time storage and driving.
- 11 January 2024
- Published by Royal Society of Chemistry (RSC) in Lab on a Chip
- Vol. 24 (4) , 896-903
A liquid metal based, integrated parallel electroosmotic micropump cluster drive system
The application of liquid metal in a microfluidic system enables the fabrication of highly integrated on-chip electroosmotic micropumps (EOPs). In this work, a low-voltage driveable integrated parallel EOP cluster drive system is proposed. This system consists of two layers, a branch-channel layer and a trunk-channel layer. The lower branch-channel layer contains separate parallel pumping channels and a pair of comb liquid metal electrodes. The separated branch channels are connected together through the trunk channels in the upper layer. With this structural arrangement, the parallel micropumps form an integrated micropump cluster for larger pumping capacity. The distance between the pumping channel and the electrode next to it is controlled to 20 μm. To guide the pump design, parametric studies are performed and fully discussed. According to the experimental results, the micropump cluster can be driven at a low voltage of 0.5 V, and the flow rate reaches 274 nL min−1 at 5 V. In addition, the paper finally proposes an electrode protection strategy and an integrated pump-valve drive system which is expected to solve the shortcoming of electroosmotic pumps in terms of long-time storage and driving.
- 5 November 2023
- Published by Springer Nature
- p. 343-351
Modified Tooth Design of a Trochoidal Sprocket for a Roller Chain Drive to Improve Positioning Accuracy
- 5 November 2023
- Published by Springer Nature
- p. 343-351
Modified Tooth Design of a Trochoidal Sprocket for a Roller Chain Drive to Improve Positioning Accuracy
- 4 November 2023
- Published by Springer Nature
- p. 950-959
Semiautomatic Experimental System Using Some Portable Robot Arms Collaborating with a Human
- 4 November 2023
- Published by Springer Nature
- p. 950-959
Semiautomatic Experimental System Using Some Portable Robot Arms Collaborating with a Human
- 18 September 2023
- Published by Cambridge University Press (CUP) in Robotica
- Vol. 41 (12) , 3687-3701
Development of the “Quad-SCARA” platform and its collision avoidance based on Buffered Voronoi Cell
As a solution to soft material manipulation, dual-arm robots that are capable of multi-point grasping have become the latest trend due to their higher capability and efficiency. To explore further development in soft material manipulation and go beyond the hardware limit of dual arms, in this paper the robot platform “Quad-SCARA” that consists of four Selective Compliance Assembly Robot Arm (SCARA) is developed and introduced. With the base of hardware platform, a novel collision avoidance system designed for the motion planning of Quad-SCARA in multi-point grasping state is proposed. This system is inspired by the idea of “Buffered Voronoi Cell (BVC),” an algorithm originally proposed for multi-agent collision avoidance. After appropriate adaptation and new proposition in implementation of BVC, the experiments of folding and spreading a handkerchief are performed, and the results in simulation and robot experiments are presented and discussed for the validation and evaluation of entire system.
- 18 September 2023
- Published by Cambridge University Press (CUP) in Robotica
- Vol. 41 (12) , 3687-3701
Development of the “Quad-SCARA” platform and its collision avoidance based on Buffered Voronoi Cell
As a solution to soft material manipulation, dual-arm robots that are capable of multi-point grasping have become the latest trend due to their higher capability and efficiency. To explore further development in soft material manipulation and go beyond the hardware limit of dual arms, in this paper the robot platform “Quad-SCARA” that consists of four Selective Compliance Assembly Robot Arm (SCARA) is developed and introduced. With the base of hardware platform, a novel collision avoidance system designed for the motion planning of Quad-SCARA in multi-point grasping state is proposed. This system is inspired by the idea of “Buffered Voronoi Cell (BVC),” an algorithm originally proposed for multi-agent collision avoidance. After appropriate adaptation and new proposition in implementation of BVC, the experiments of folding and spreading a handkerchief are performed, and the results in simulation and robot experiments are presented and discussed for the validation and evaluation of entire system.
- 16 April 2023
- Published by Springer Nature
- p. 243-253
Novel Design of an Orthogonal-Axis Type Precession Motion Ball Reducer
- 16 April 2023
- Published by Springer Nature
- p. 243-253
Novel Design of an Orthogonal-Axis Type Precession Motion Ball Reducer