RGRosendo Jesús Galán-Arboledas

Rosendo Jesús Galán-Arboledas

*This is an algorithmically generated author record based on publicly available information.

Rosendo Jesús Galán-Arboledas has a total of 11 co-authors. Here are the top co-authors by number of shared publications:

  • Salvador Bueno

    Department of Chemical, Environmental, and Materials Engineering, Higher Polytechnic School of Jaén, University of Jaen, Campus Las Lagunillas s/n, 23071 Jaén, Spain

    7 shared publications
  • Carmen Martínez-García

    Department of Chemical, Environmental and Materials Engineering, Higher Polytechnic School of Linares, University of Jaén, Campus Cientifico-Tecnologico de Linares, 23700 Linares, Jaén, Spain

    4 shared publications
  • Teresa Cotes-Palomino

    Department of Chemical, Environmental and Materials Engineering, Higher Polytechnic School of Linares, University of Jaén, Campus Cientifico-Tecnologico de Linares, 23700 Linares, Jaén, Spain

    3 shared publications
  • A. Merino

    Fundación Innovarcilla. Centro Tecnológico de la Cerámica de Andalucía, Jaén

    1 shared publication
  • Aarón Merino García

    Fundación Innovarcilla (Centro Tecnológico de la Cerámica de Andalucía)

    1 shared publication
  • Francisco Javier Iglesias-Godino

    Department of Chemical, Environmental and Materials Engineering, Higher Polytechnic School of Linares, University of Jaén, Campus Cientifico-Tecnologico de Linares, 23700 Linares, Jaén, Spain

    1 shared publication

Latest Publications

  • Open Access

    Alkaline fusion–hydrothermal synthesis of Losod zeolite from industrial waste for CO 2 capture

    by Rosendo J. Galán-Arboledas, Francisco Javier Iglesias-Godino, Jacinto Alonso-Azcárate, Carmen Martínez-García

    This work studies the hydrothermal synthesis of zeolitic materials from three types of industrial waste (granite cutting sludge; slate cutting sludge and aggregate washing sludge), which are regarded as low-cost materials. The synthesis was carried out through acid pretreatment with aqua regia to minimize iron content, followed by alkaline melting at 600°C followed by a hydrothermal crystallization stage at 180°C for 12 h. Characterization of the three synthesized zeolite materials by X-ray fluorescence, X-ray diffraction, Fourier-transform infrared spectroscopy and scanning electron microscopy with energy-dispersive X-ray spectroscopy confirmed that the methodology used induced the formation of LOS (Losod) zeolite (Na 12 Al 12 Si 12 O 48 · x H 2 O) as the predominant phase in all products, regardless of the waste used as the raw material. The end-products have a significant amorphous fraction (33–43 wt.%) and a zeolitic crystalline fraction (51–66 wt.%) and are enriched in Na and Al, and they have Si/Al and Na/Al ratios ranging from 1.27 to 1.39 and from 0.58 to 1.05, respectively, characteristic of low-silica zeolites. The synthetic zeolites showed reduced CO 2 adsorption capacities at room temperature (0.50–0.55 mmol g –1 ) compared to commercial zeolites such as 13X (3.45 mmol g –1 ).

  • Ternary diagrams as a tool for developing ceramic materials from waste: relationship between technological properties and microstructure

    by Rosendo Jesús Galán-Arboledas, María Teresa Cotes-Palomino, Carmen Martínez-García, José Manuel Moreno-Maroto, Manuel Uceda-Rodríguez, Salvador Bueno

    The present work proposes the manufacture of ceramic construction materials using raw materials which are only industrial wastes from different production processes (electric arc furnace steel slag, coal bottom ash, carbon fly ash, and oil-filtering diatomaceous-earth). From them, the SiO2-Al2O3-CaO equilibrium phase diagram has been used to formulate two materials compositions with the objective of obtaining ceramics whose chemical composition is located in the same area as a traditional clay-based material, but with two different technological behaviors: refractoriness due to calcium phase’s development and densification due to a greater melting capacity. The waste-based pieces have been sintered at three firing temperatures (1000 °C, 1050 °C, and 1100 °C) and the mineralogical composition has been quantified by Rietveld refinement-XRD in order to establish the agreement between the phases foreseen by the formulations in the diagrams and the mineralogical compositions actually developed after the sintering treatment. In addition, fired materials have been subjected to a complete microstructural characterization by means of SEM-EDX and the pore size distribution has been determined by means of mercury intrusion porosimetry and helium pycnometry. In general, all obtained materials display adequate technological properties for their use as building materials so this characterization has allowed to show the suitability of the ternary diagram SiO2-Al2O3-CaO for the design of ceramic compositions from industrial wastes. Therefore, extending the use of phase diagrams as a design tool is still little explored for waste-based ceramics, and those that have been mainly used for studying Mg-based phases can have an important contribution to a more sustainable construction sector.


  • Open Access

    Influence of waste addition on the porosity of clay-based ceramic membranes

    by Rosendo J. Galán-Arboledas, Teresa Cotes, Carmen Martínez, Salvador Bueno

    Incorporation of waste into ceramics can be an eco-friendly alternative for modification of their microstructure and related properties such as porosity, pore size and, therefore, permeability and mechanical properties. In this work, two wastes are added to a common clay mixture traditionally used for porous ceramics manufacturing: Screen Glass, G, from monitors and TV panels, and Diatomaceous Earth, D, from oil-filtering processes. Processing of the reference clay-based material (R) and two waste-containing formulations (10 wt.% of Screen Glass, R10G, and 10 wt.% of Diatomaceous Earth, R10D) was carried out through vacuum extrusion shaping and firing of test specimens at three maximum temperatures: 850, 950, and 1,050°C. Final sintered specimens were characterized to determine density, bending strength, and water absorption. Microstructure was observed by SEM while pore size distribution was determined by mercury intrusion porosimetry. Permeability coefficient was calculated from these experimental parameters. Materials containing Glass waste have lower porosity and larger pore size due to partial melting of glass. As a consequence, mechanical strength of R10G increases around 10% due to the lower porosity while, contrary to expectations, permeability also increases due to the larger pore size. In the case of R10D materials, extra porosity created by oil combustion during sintering also leads to larger permeability values although a significant decrease of mechanical strength and reliability is observed.


  • Lighter Structural Clay Ceramics Manufactured with Marble Cutting Dust and Paperboard Based Packaging Waste

    by Rosendo J. Galán Arboledas, Aarón Merino García, Salvador Bueno

    This work evaluates some preliminary results of adding two kinds of wastes in two characteristics clay mixtures with the aim of producing lighter structural ceramic products. The selected wastes are marble cutting dust and a packaging waste mainly composed by paperboard and polyethylene. In the case of clay mixtures, they are focused to the manufacture of both common and facing bricks. New waste based formulations are proposed on the basis of chemical and mineralogical compositions of clays and wastes and previous experiences in literature. Especial attention is paid to initial carbonate content in the selected clays, since marble waste is almost exclusively formed by calcite. Dynamic sintering tests and technological properties characterization were performed to analyse the feasibility of waste incorporation. Sintering behaviour shows a larger influence of marble dust waste and it is radically changed in the case of clay mixtures for facing products. Technology properties of unfired specimens are in general adequate for the industrial practice. Final technological properties of sintered specimens shows lower density for the new waste bearing products but not unique trends with sintering temperature for another properties as bending strength or water absorption capacity. These properties are mainly conditioned by the sintering behaviour associated to marble dust addition and, thus additional microstructure and mineralogy test would be necessary for a better knowledge of these materials and their optimised formulation.


  • Production of Ceramic Materials Using only Waste as Raw Materials

    by R.J. Galán-Arboledas, Salvador Bueno

    From a selection of inorganic industrial waste (screen glass, steelworks ashes, coal power plant ashes, biomass power plant ash and sludge from cutting marble industry) and a waste with organic fraction (diatomaceous earth from oil filtration) it is expected to obtain ceramic materials with properties similar to those of ceramic materials used in construction and porous materials with thermal insulating capability. The ternary phase equilibrium diagram SiO2-Al2O3-CaO has been used as the main tool for the formulation of these materials. The dynamic sintering study was carried out using dilatometry techniques (DIL), thermo gravimetric analysis and differential scanning calorimetry (TG-DSC). Characterization of the manufactured material allows determining a set of basic technological properties such as fired bulk density, water absorption capacity and bending strength, in addition to thermal conductivity and microstructure by SEM-EDX, in order to obtain the necessary data to determine technical feasibility.


  • Open Access

    Use of new raw materials and industrial wastes to improve the possibilities of using ceramic materials from Bailén (Jaén, southern Spain)

    by R. J. Galán-Arboledas, A. Merino, S. Bueno

    Raw materials used by the ceramic industry in Jaén (southern Spain) consist of mixtures of carbonated clays from the Guadalquivir Basin and red clays from the Iberian Massif. The mixtures formulation usually obeys empirical experience developed by this industry for many generations. This work evaluates different possibilities of using these raw materials to manufacture new ceramic products on the basis of clay physical-chemical properties and analyzes limitations to produce high added value products. As an alternative to overcome these limitations, the mixture of these clays with raw materials from near regions (pyrophyllite clay) and with different industrial wastes is proposed. These wastes are screen glass from monitors and oil impregnated diatomaceous earth. The study of the technological properties shows that the new mixtures are suitable for the processing of ceramic products in which structural and thermal insulating properties are improved or kept.