Ali M. Niknejad
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Ali M. Niknejad has a total of 127 co-authors. Here are the top co-authors by number of shared publications:
- Mekhail Anwar
University of California, San Francisco
6 shared publications - Nai-Chung Kuo
Berkeley Wireless Research Center, University of California at Berkeley, Berkeley, CA 94720 USA
6 shared publications - Ali Ameri
Department of Electrical Engineering and Computer Science (EECS), University of California, Berkeley, Berkeley, CA, USA
5 shared publications Elad Alon
Blue Cheetah Analog Design, Sunnyvale, CA, USA
5 shared publications- Hesham Beshary
Department of Electrical Engineering and Computer Sciences, University of California at Berkeley, Berkeley, CA, USA
5 shared publications - Lorenzo Iotti
Department of Electrical Engineering and Computer Science, University of California at Berkeley, Berkeley, CA, USA
5 shared publications
Latest Publications
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (10) , 5589-5600
A Performance Comparison Between W-Band Sequential and Doherty Power Amplifiers for Power Back-Off Efficiency Improvement
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (10) , 5589-5600
A Performance Comparison Between W-Band Sequential and Doherty Power Amplifiers for Power Back-Off Efficiency Improvement
- 29 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. PP (15498328) , 1-14
Theoretical Studies of Sub-THz Active Split-Ring Resonators for Near-Field Imaging
This paper develops a theoretical framework for the design of Active Split-Ring Resonators (ASRRs). An ASRR is a Split-Ring Resonator (SRR) equipped with a tunable negative resistor, enabling both switchability and quality factor boosting and tuning. These properties make ASRRs well-suited for integration into dense arrays on silicon chips, where pixelated near-fields are generated and leveraged for high-resolution 2D imaging of samples. Such imagers pave the way for real-time, non-invasive, and low-cost imaging of human body tissue. The paper investigates ASRR coupling to host transmission lines, nonlinear effects, signal flow, and the influence of various noise sources on detection performance. Verified through simulations, these studies provide design guidelines for optimizing the Signal-to-Noise Ratio (SNR) and power consumption of a single pixel, while adhering to the constraints of a scalable array.
- 29 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. PP (15498328) , 1-14
Theoretical Studies of Sub-THz Active Split-Ring Resonators for Near-Field Imaging
This paper develops a theoretical framework for the design of Active Split-Ring Resonators (ASRRs). An ASRR is a Split-Ring Resonator (SRR) equipped with a tunable negative resistor, enabling both switchability and quality factor boosting and tuning. These properties make ASRRs well-suited for integration into dense arrays on silicon chips, where pixelated near-fields are generated and leveraged for high-resolution 2D imaging of samples. Such imagers pave the way for real-time, non-invasive, and low-cost imaging of human body tissue. The paper investigates ASRR coupling to host transmission lines, nonlinear effects, signal flow, and the influence of various noise sources on detection performance. Verified through simulations, these studies provide design guidelines for optimizing the Signal-to-Noise Ratio (SNR) and power consumption of a single pixel, while adhering to the constraints of a scalable array.
- 17 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (7) , 4943-4952
Beam Squint Analysis and Mitigation Using Spatial IDFT for Massive Wideband Arrays
This paper presents a comprehensive analysis of the beam-squint phenomenon in wideband massive phased arrays and proposes an architecture to achieve squint-free operation. In wideband phased arrays, the sources of beam squint are coherent bandwidth limitations and systematic delay spread, which degrade the signal-to-noise ratio (SNR) and introduce inter-symbol interference (ISI). The presented analysis quantifies these sources and derives the relationship between array parameters and performance degradation. In addition, this work demonstrates that orthogonal frequency-division multiplexing (OFDM) modulation significantly mitigates self-interference caused by delay spread. Building on this analysis, a spatial inverse discrete Fourier transform (IDFT) architecture is proposed that cancels the intrinsic DFT effect of phased arrays, enabling fully coherent combining across all subcarriers. Using error vector magnitude (EVM) as a performance metric, beam squint and the proposed OFDM and IDFT implementations are evaluated through numerical simulations.
- 17 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (7) , 4943-4952
Beam Squint Analysis and Mitigation Using Spatial IDFT for Massive Wideband Arrays
This paper presents a comprehensive analysis of the beam-squint phenomenon in wideband massive phased arrays and proposes an architecture to achieve squint-free operation. In wideband phased arrays, the sources of beam squint are coherent bandwidth limitations and systematic delay spread, which degrade the signal-to-noise ratio (SNR) and introduce inter-symbol interference (ISI). The presented analysis quantifies these sources and derives the relationship between array parameters and performance degradation. In addition, this work demonstrates that orthogonal frequency-division multiplexing (OFDM) modulation significantly mitigates self-interference caused by delay spread. Building on this analysis, a spatial inverse discrete Fourier transform (IDFT) architecture is proposed that cancels the intrinsic DFT effect of phased arrays, enabling fully coherent combining across all subcarriers. Using error vector magnitude (EVM) as a performance metric, beam squint and the proposed OFDM and IDFT implementations are evaluated through numerical simulations.
- 16 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (4) , 463-467
A Comprehensive High-to-Low Delay Model for NCFET Circuits
In this work, we present a comprehensive high-to-low propagation delay model for NCFET based circuits–which is also fully compatible with any baseline Si-MOSFET. The proposed physics-based analytical delay model is quick to converge, portable, covers all regions of operation, and is technology independent. The model is successfully validated against the 90nm Berkeley NCFET measurement data as well as different commercial MOSFET Process Design Kit (PDK)–under variable device dimensions, supply voltage, external load and temperature.
- 16 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (4) , 463-467
A Comprehensive High-to-Low Delay Model for NCFET Circuits
In this work, we present a comprehensive high-to-low propagation delay model for NCFET based circuits–which is also fully compatible with any baseline Si-MOSFET. The proposed physics-based analytical delay model is quick to converge, portable, covers all regions of operation, and is technology independent. The model is successfully validated against the 90nm Berkeley NCFET measurement data as well as different commercial MOSFET Process Design Kit (PDK)–under variable device dimensions, supply voltage, external load and temperature.
- 3 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (3) , 278-282
Frequency Stabilization of a 100-GHz VCO Using Resonator-Locked Loops in CMOS 28-nm
This brief presents a novel frequency-locking technique in which two off-tuned chopped active resonators define a reference frequency to which a 100GHz voltage-controlled oscillator (VCO) is locked. Deviations from the reference frequency result in a power imbalance between the resonator outputs. This imbalance is detected and used as an error signal to restore the VCO frequency to the reference point. The loop operates without frequency dividers and off-chip references. The implementation, fabricated in a CMOS 28nm process, achieves a close-in phase noise suppression of up to 5.6dB at -3dBm output power, consuming only 24mW.
- 3 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 73 (3) , 278-282
Frequency Stabilization of a 100-GHz VCO Using Resonator-Locked Loops in CMOS 28-nm
This brief presents a novel frequency-locking technique in which two off-tuned chopped active resonators define a reference frequency to which a 100GHz voltage-controlled oscillator (VCO) is locked. Deviations from the reference frequency result in a power imbalance between the resonator outputs. This imbalance is detected and used as an error signal to restore the VCO frequency to the reference point. The loop operates without frequency dividers and off-chip references. The implementation, fabricated in a CMOS 28nm process, achieves a close-in phase noise suppression of up to 5.6dB at -3dBm output power, consuming only 24mW.
- 20 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Magazine
- Vol. 18 (1) , 74-85
High-Power and Highly Efficient CMOS Power Amplifiers for D-Band Applications in Silicon: Design methodologies that extend CMOS power, gain, and bandwidth toward sub-terahertz operation
As demand grows for multigigabit data links, high-resolution radar, and precision sensing, operating frequencies are being driven deep into the sub-terahertz (sub-THz) spectrum, where the D- and G-bands (110–220 GHz) offer immense bandwidth (BW). However, operating at these frequencies with CMOS silicon technologies reveals several fundamental physical limitations, including limited breakdown voltage, low intrinsic gain, dominant parasitics, and significant passive losses. This article brings together different design methodologies that push these limits and expand the achievable power, gain, and BW of CMOS power amplifiers (PAs) operating near ${f}_{\max}$ The first approach revisits the concept of transistor stacking from a large-signal modeling perspective. By analytically accounting for all parasitic elements and the intrinsic delay of each device, a systematic framework is developed to determine the optimum input, output, and gate impedances for every transistor in the stack. A 45-nm SOI prototype that combines multiple stacked stages through a low-loss 4:1 combiner demonstrates 18.7 dBm saturated output power and 4.8% power-added efficiency (PAE) at 200 GHz, an example of how careful modeling can turn CMOS voltage limits into a scalable power generation strategy. The second methodology focuses on gain enhancement through embedding. At sub-THz frequencies, where matching-network losses can rival transistor gain, a passive feedback network is introduced and tuned on a “gain plane” that maps equi-gain and equi-load-conductance contours. This graphical design tool allows the simultaneous optimization of gain and output power. Implemented in a 65-nm CMOS 2 × 8 cell amplifier, the embedded approach achieves 19.5 dB gain and 9.4 dBm saturated power at 200 GHz, showing how modest feedback can recover otherwise-lost gain and extend usable output levels. The third technique, reverse-feedback amplification, breaks the BW barrier. By introducing a controlled amount of negative resistance into each amplifier cell, a distributed line is formed that supports constructive wave propagation and continuous power addition without interstage matching. Two 45-nm CMOS G-band amplifiers fabricated using this principle deliver up to 20.4 dB gain and 3.8% PAE across a 156- to 194-GHz 3-dB BW. Together, these methodologies, large-signal stacking, gain plane embedding, and distributed reverse feedback, demonstrate how thoughtful circuit architectures can overcome fundamental device limits to achieve high-power, high-efficiency, and broadband amplification in standard CMOS.
- 20 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Magazine
- Vol. 18 (1) , 74-85
High-Power and Highly Efficient CMOS Power Amplifiers for D-Band Applications in Silicon: Design methodologies that extend CMOS power, gain, and bandwidth toward sub-terahertz operation
As demand grows for multigigabit data links, high-resolution radar, and precision sensing, operating frequencies are being driven deep into the sub-terahertz (sub-THz) spectrum, where the D- and G-bands (110–220 GHz) offer immense bandwidth (BW). However, operating at these frequencies with CMOS silicon technologies reveals several fundamental physical limitations, including limited breakdown voltage, low intrinsic gain, dominant parasitics, and significant passive losses. This article brings together different design methodologies that push these limits and expand the achievable power, gain, and BW of CMOS power amplifiers (PAs) operating near ${f}_{\max}$ The first approach revisits the concept of transistor stacking from a large-signal modeling perspective. By analytically accounting for all parasitic elements and the intrinsic delay of each device, a systematic framework is developed to determine the optimum input, output, and gate impedances for every transistor in the stack. A 45-nm SOI prototype that combines multiple stacked stages through a low-loss 4:1 combiner demonstrates 18.7 dBm saturated output power and 4.8% power-added efficiency (PAE) at 200 GHz, an example of how careful modeling can turn CMOS voltage limits into a scalable power generation strategy. The second methodology focuses on gain enhancement through embedding. At sub-THz frequencies, where matching-network losses can rival transistor gain, a passive feedback network is introduced and tuned on a “gain plane” that maps equi-gain and equi-load-conductance contours. This graphical design tool allows the simultaneous optimization of gain and output power. Implemented in a 65-nm CMOS 2 × 8 cell amplifier, the embedded approach achieves 19.5 dB gain and 9.4 dBm saturated power at 200 GHz, showing how modest feedback can recover otherwise-lost gain and extend usable output levels. The third technique, reverse-feedback amplification, breaks the BW barrier. By introducing a controlled amount of negative resistance into each amplifier cell, a distributed line is formed that supports constructive wave propagation and continuous power addition without interstage matching. Two 45-nm CMOS G-band amplifiers fabricated using this principle deliver up to 20.4 dB gain and 3.8% PAE across a 156- to 194-GHz 3-dB BW. Together, these methodologies, large-signal stacking, gain plane embedding, and distributed reverse feedback, demonstrate how thoughtful circuit architectures can overcome fundamental device limits to achieve high-power, high-efficiency, and broadband amplification in standard CMOS.
- 23 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-16
Design and Implementation of a 200-GHz 200-Pixel 2-D Near-Field Imager
This article introduces a new technique for integrating a dense 2-D array of resonator-based pixels, enabling sub-wavelength-resolution near-field imaging. The imaging pixels consist of active split-ring resonators (ASRRs) operating at 200GHz. The active component allows for tuning and boosting the quality factor ( $Q$ ) of the resonator to values that are not otherwise achievable on-chip. ASRRs exhibit an amplified sensitivity equal to the square of the $Q$ -boosting factor. Additionally, these resonators enable the selection and readout of pixels individually and in isolation from the neighboring pixels. The overall footprint of a pixel is $54 {\times } 46~{\mu \text {m} ^{2}}$ while achieving −27-dB pixel-to-pixel isolation. The imager, as a fully integrated system, is comprised of compact and efficient 200-GHz signal sources and distribution networks, 200 imaging pixels configured in 20 rows and ten columns, detectors, and baseband signal processing. Phase detection and correlated double sampling (CDS) are employed to suppress the close-in phase noise of the sub-THz voltage-controlled oscillator (VCO) in addition to the flicker noise of the detection chain, collectively resulting in a 58.5 dB of dynamic range (DR). The imager was implemented in a 28-nm bulk CMOS process and consumes a total of 79 mW of power during image acquisition. The platform, after biocompatible packaging, was demonstrated in near-field imaging of multiple biological and synthetic tissues, resulting in high-contrast delineation of various sections of the sample. The imaging pixels respond to the real and imaginary parts of the sample permittivity differently, allowing for decoupled measurements and image reconstruction based on these quantities.
- 23 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-16
Design and Implementation of a 200-GHz 200-Pixel 2-D Near-Field Imager
This article introduces a new technique for integrating a dense 2-D array of resonator-based pixels, enabling sub-wavelength-resolution near-field imaging. The imaging pixels consist of active split-ring resonators (ASRRs) operating at 200GHz. The active component allows for tuning and boosting the quality factor ( $Q$ ) of the resonator to values that are not otherwise achievable on-chip. ASRRs exhibit an amplified sensitivity equal to the square of the $Q$ -boosting factor. Additionally, these resonators enable the selection and readout of pixels individually and in isolation from the neighboring pixels. The overall footprint of a pixel is $54 {\times } 46~{\mu \text {m} ^{2}}$ while achieving −27-dB pixel-to-pixel isolation. The imager, as a fully integrated system, is comprised of compact and efficient 200-GHz signal sources and distribution networks, 200 imaging pixels configured in 20 rows and ten columns, detectors, and baseband signal processing. Phase detection and correlated double sampling (CDS) are employed to suppress the close-in phase noise of the sub-THz voltage-controlled oscillator (VCO) in addition to the flicker noise of the detection chain, collectively resulting in a 58.5 dB of dynamic range (DR). The imager was implemented in a 28-nm bulk CMOS process and consumes a total of 79 mW of power during image acquisition. The platform, after biocompatible packaging, was demonstrated in near-field imaging of multiple biological and synthetic tissues, resulting in high-contrast delineation of various sections of the sample. The imaging pixels respond to the real and imaginary parts of the sample permittivity differently, allowing for decoupled measurements and image reconstruction based on these quantities.