Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Giuseppe Zullo has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Analysis of the Edging Torque Distribution in Alpine Touring Bindings: Comparison of Three Locking Technologies in Laboratory and Skiing Tests

    by Lorenzo Crosetta, Giuseppe Zullo, Alexis Lussier Desbiens, Nicola Petrone, Martino Colonna

    Choice of proper equipment is crucial in skiing since it could alter the safety and performance. Ski bindings are a major element related to these aspects and in particular Alpine Touring (AT) bindings available in the market show conceptually different design solutions. We identified three macro categories of AT bindings distinguished by the clamp mechanisms at heel and toe. Then, we took a representative model for each, aiming to test if the structural differences of these bindings influence the repartition of edging torque between front and rear parts of the binding. We hypothesize that the tightness of the joint mechanism and its fully metallic construction makes the frontal connection of pin bindings very stiff therefore driving most of the torque to the front binding, which doesn’t happen in alpine-style bindings since the two clamp connections show similar contact geometry. To test our hypothesis, we used two dynamometric plates mounted under each binding, and we measured the front, rear, and total ski edging torque in indoor and skiing experiments. Results confirmed our hypothesis showing that pin bindings can drive up to 92 % of the total torque to the front piece, while alpine-style bindings are really close to an even distribution. This evidence should be considered when designing AT ski boots to guarantee proper structural properties. Moreover, these differences should also be carefully looked towards safety regulations and release characteristics of AT bindings.

  • Open Access

    Experimental and Numerical Analysis of the Motion of Motorcycle Riders

    by Luca Bassani, Stefano Lovato, Matteo Massaro, Nicola Petrone, Giuseppe Zullo, Matteo Formentini, Roberto Lot

    The location of the rider centre of mass (CoM) is especially relevant in bicycles and motorcycles due to the large human-to-vehicle mass ratio. This work illustrates two alternative methods for the experimental identification of the longitudinal and lateral coordinates of the rider CoM position as a function of the posture. The first method uses a set of load cells and provides accurate and reliable results. However, riders’ must firmly hold their configuration for the time necessary to stabilise the force measurements, which may be uncomfortable in configurations such as lean-out. The second method utilises an optical system which captures the rider attitude. This information is then used to feed a multibody model, which is used to estimate the CoM coordinates.

  • Open Access

    Development of a coupled experimental–numerical methodology using an instrumented human head replica for impact testing

    by Elisa Baldoin, Giuseppe Zullo, Piergiorgio Carraretto, Andrey Koptyug, Piero G. Pavan, Nicola Petrone

    Head injury prevention is a crucial concern within the healthcare system and scientific community. Experimental and numerical trials play a key role, utilizing anthropomorphic test devices and human head numerical models to study impact scenarios. However, rigid headforms, Like Hybrid III or EN 960, lack biofidelity, suggesting a need for more refined physical models, such as NOCSAE standardized headform. Moreover, the direct development of human head numerical models relies on testing cadaveric tissues. Therefore, a biofidelic instrumented human head replica embedding synthetic simulants of cerebrospinal fluid, meninges, and brain was developed at the University of Padova in collaboration with Mid Sweden University. As part of this activity, the present study proposes an integrated experimental–numerical methodology for impact testing, involving the development of a finite element model of this replica. This also supports the future development of human head models having the same geometry as physical replicas. Preliminarily, the proposed workflow involves the mechanical characterization of the materials used for the replica and the geometry reconstruction for the subsequent numerical analysis. This was performed with an explicit dynamic algorithm to simulate impacts of the physical bare replica onto a flat anvil using a drop tower. An example of the collection and analysis of experimental and numerical data is presented as a preliminary validation of the model. The interpretation of these results is provided as a basis for refinements, before the study of helmeted impacts. The results show that the current model needs improvements in terms of coupling mechanisms and skin and fluid constitutive formulations.


  • Open Access

    Development of the Biofidelic Instrumented Neck Surrogate (BINS) with Tunable Stiffness and Embedded Kinematic Sensors for Application in Static Tests and Low-Energy Impacts

    by Giuseppe Zullo, Elisa Baldoin, Leonardo Marin, Andrey Koptyug, Nicola Petrone

    Road accidents could result in severe or fatal neck injuries. A few surrogate necks are available to develop and test neck protectors as countermeasures, but each has its own limitations. The objective of this study was to develop a surrogate neck compatible with the Hybrid III dummy, focused on tunable flexural stiffness and integrated angular sensors for kinematic feedback during impact tests. The neck features six 3D-printed surrogate vertebral bodies interconnected by rubber surrogate discs, providing a baseline flexibility to the surrogate fundamental spinal units. An adjustable inner cable and elastic elements hooked on the sides of vertebral elements allow to increase the flexural stiffness of the surrogate and to simulate the asymmetric behavior of the human neck. Neck flexural angles and axial compression are measured using a novel system made of wires, pulleys, and rotary potentiometers embedded in the neck base. A motion capture system and a load cell were used to determine the bending and torsional stiffness of the neck and to calibrate the sensors. Results showed that the neck flexural stiffness can be tuned between 3.29 and 5.76 Nm/rad. Torsional stiffness was 1.01 Nm/rad and compression stiffness can be tuned from 39 to 193 N/mm. Sensor flexural angles were compared with motion capture angles, showing an RMSE error of 1.35° during static testing and of 3° during dynamic testing. The developed neck could be a viable tool for investigating neck braces from a kinematic and kinetic perspective due to its inbuilt sensing ability and its tunable stiffness.


  • Open Access

    Center of Pressure Behavior in Response to Unexpected Base of Support Shifting: A New Objective Tool for Dynamic Balance Assessment

    by Alex Rizzato, Matteo Bozzato, Giuseppe Zullo, Antonio Paoli, Giuseppe Marcolin

    The translation of the base of support represents a promising approach for the objective assessment of dynamic balance control. Therefore, this study aimed to present a servo-controlled, electrically driven movable plate and a new set of parameters based on the center-of-pressure (CoP) trajectory. Twenty subjects were assessed on a force platform screwed over a movable plate that could combine the following settings: direction (forward (FW) and backward (BW)), displacement (25 mm, 50 mm, and 100 mm), and ramp rate (100 mm/s and 200 mm/s). The subjects underwent two sets of 12 trials randomly combining the plate settings. From the CoP trajectory of the 2.5 s time window after the perturbation, the 95% confidence-interval ellipse (Area95) and the CoP mean velocity (Unit Path) were calculated. Within the same time window, the first peak (FP), the maximal oscillations (ΔCoPMax), and the standard deviation (PPV) of the CoP anterior–posterior trajectory were calculated. The plate direction (p < 0.01), ramp rate (p < 0.001), and displacement (p < 0.01) affected the Area95, FP, and ΔCoPMax, while the Unit Path and PPV were influenced only by the ramp rate (p < 0.001) and displacement (p < 0.001). The servo-controlled, electrically driven movable plate and the CoP-related parameters presented in this study represent a new promising objective tool for dynamic balance assessment.


  • Open Access

    Torsion and bending loads on a ski-touring boot shell during uphill and downhill skiing

    by Giuseppe Zullo, Pierluigi Cibin, Nicola Petrone

    Ski touring is an established winter activity that has experienced a recent increase in popularity. Differently to alpine skiing, skier gains altitude without lifts, thus equipment weight must be minimized. Nevertheless, structural properties of the equipment, such as ski boots, must be adequate to withstand skiing loads. Several studies provided data on flexural stiffness of alpine ski boots in bench and field tests. The present study focused on the torsional properties of ski-touring boots. Indeed, touring bindings design implies a higher torque transmission to the front piece which induces a torsional load throughout the shell. To conduct the study, we prepared a ski-touring boot with strain gage bridges, and we performed bench tests to determine the stiffness of the boot and the bridge sensitivity. We also positioned and calibrated strain gage bridges to measure bending load in the shell and axial load in the ski/walk lever placed between shell and cuff of the boot. Then, we conducted a field test measuring the loads during a ski-touring trip including ascent and descent. Bench tests evidenced linearity of the torsion sensor, and a variation of stiffness depending on dummy leg absence/presence and boot buckle setting. Field tests showed torque ranges of 17 Nm in climbing and of 27 Nm in skiing. Bending moment range on the boot shell was of 150 and 228 Nm, respectively. Maximum force on the ski/walk mechanism reached 570 N. Results could be useful to test ski-touring boot performances and to optimize their design.


  • Open Access

    An Innovative Compact System to Measure Skiing Ground Reaction Forces and Flexural Angles of Alpine and Touring Ski Boots

    by Giuseppe Zullo, Pierluigi Cibin, Lorenzo Bortolan, Michele Botteon, Nicola Petrone

    Skiing is a popular winter activity spanning various subdisciplines. Key hardware are ski boots, bindings, and skis, which are designed to withstand loads generated during skiing. Obtaining service forces and moments has always been challenging to researchers in the past. The goal of the present study is to develop and test a lightweight and compact measurement system to obtain the Ground Reaction Forces and the kinematics for ski touring and alpine ski. To do so, we adapted two six-axis load cells to fit into ski touring and alpine skis adding 20 mm height and 500 g weight to the original ski. To measure kinematics, we created custom angular sensors from rotary potentiometers. The system was tested indoors using a force platform and motion capture system before a first set of field tests in which the sensors were used to measure ski touring and alpine skis kinetics and kinematics. Validation trials showed maximum errors of 10% for kinetics and 5% for kinematics. Field tests showed data in agreement with previous findings on the topic. The results of this study show the possibility of using our system to study biomechanics and equipment performances for ski touring, alpine skiing, and possibly other disciplines.


  • Open Access

    A Novel Multi-Axial Pressure Sensor Probe for Measuring Triaxial Stress States Inside Soft Materials

    by Giuseppe Zullo, Anna Leidy Silvestroni, Gianluca Candiotto, Andrey Koptyug, Nicola Petrone

    This paper presents the concept, design, construction, and validation of a novel probe based on the hexadic disposition of six pressure sensors suitable for measuring triaxial stress states inside bulky soft materials. The measurement of triaxial stress states inside bulk materials such as brain tissue surrogates is a challenging task needed to investigate internal organs’ stress states and validate FE models. The purpose of the work was the development and validation of a 17 × 17 × 17 mm probe containing six pressure sensors. To do so, six piezoresistive pressure sensors of 6 mm diameter were arranged into an hexad at three cartesian axes and bisecting angles, based on the analytical solution of the stress tensor. The resulting probe was embedded in a soft silicone rubber of known characteristics, calibrated under cyclic compression and shear in three orientations, and statically validated with combined loads. A calibration matrix was computed, and validation tests allowed us to estimate Von Mises stress under combined stress with an error below 6%. Hence, the proposed probe design and method can give indications about the complex stress state developing internally to soft materials under triaxial high-strain fields, opening applications in the analysis of biological models or physical surrogates involving parenchyma organs.


  • Effect of outdoor footwear bending stiffness on metatarsophalangeal joint kinematics, kinetics, and energy balance during level and uphill walking

    by Giuseppe Zullo, Giuseppe Marcolin, Paolo Mistretta, Nicola Petrone

    In outdoor footwear, sole properties must guarantee grip with the ground and support the forefoot without altering the kinematics of the metatarsophalangeal joints (MPJ). The present study aimed to implement an objective measure of shoe bending stiffness and investigate the effect of shoes with different bending stiffness on MPJ kinematics, kinetics, and energy balance during walking. The bending stiffness of four shoes was calculated using a customized flexometer. Then, the influence of each footwear on MPJ biomechanics during level and uphill walking was investigated with a motion capture system and a force plate on 10 healthy subjects. Results showed that MPJ peak dorsiflexion angle, stiffness, and energy balance were affected both by shoe bending stiffness (pp<0.001). The findings of the study, which quantify the influence of shoe stiffness on MPJ biomechanics, will be helpful in the design of outdoor footwear.